docs: hwmon: Add an index file and rename docs to *.rst

Now that all files were converted to ReST format, rename them
and add an index.

Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

1 files changed, 0 insertions, 94 deletions

diff --git a/Documentation/hwmon/adt7470 b/Documentation/hwmon/adt7470
deleted file mode 100644
index d225f816e992..000000000000
--- a/Documentation/hwmon/adt7470
+++ /dev/null
@@ -1,94 +0,0 @@
-Kernel driver adt7470
-=====================
-
-Supported chips:
-
-  * Analog Devices ADT7470
-
-    Prefix: 'adt7470'
-
-    Addresses scanned: I2C 0x2C, 0x2E, 0x2F
-
-    Datasheet: Publicly available at the Analog Devices website
-
-Author: Darrick J. Wong
-
-Description
------------
-
-This driver implements support for the Analog Devices ADT7470 chip.  There may
-be other chips that implement this interface.
-
-The ADT7470 uses the 2-wire interface compatible with the SMBus 2.0
-specification. Using an analog to digital converter it measures up to ten (10)
-external temperatures. It has four (4) 16-bit counters for measuring fan speed.
-There are four (4) PWM outputs that can be used to control fan speed.
-
-A sophisticated control system for the PWM outputs is designed into the ADT7470
-that allows fan speed to be adjusted automatically based on any of the ten
-temperature sensors. Each PWM output is individually adjustable and
-programmable. Once configured, the ADT7470 will adjust the PWM outputs in
-response to the measured temperatures with further host intervention.  This
-feature can also be disabled for manual control of the PWM's.
-
-Each of the measured inputs (temperature, fan speed) has corresponding high/low
-limit values. The ADT7470 will signal an ALARM if any measured value exceeds
-either limit.
-
-The ADT7470 samples all inputs continuously.  A kernel thread is started up for
-the purpose of periodically querying the temperature sensors, thus allowing the
-automatic fan pwm control to set the fan speed.  The driver will not read the
-registers more often than once every 5 seconds.  Further, configuration data is
-only read once per minute.
-
-Special Features
-----------------
-
-The ADT7470 has a 8-bit ADC and is capable of measuring temperatures with 1
-degC resolution.
-
-The Analog Devices datasheet is very detailed and describes a procedure for
-determining an optimal configuration for the automatic PWM control.
-
-Configuration Notes
--------------------
-
-Besides standard interfaces driver adds the following:
-
-* PWM Control
-
-* pwm#_auto_point1_pwm and pwm#_auto_point1_temp and
-* pwm#_auto_point2_pwm and pwm#_auto_point2_temp -
-
-  - point1: Set the pwm speed at a lower temperature bound.
-  - point2: Set the pwm speed at a higher temperature bound.
-
-The ADT7470 will scale the pwm between the lower and higher pwm speed when
-the temperature is between the two temperature boundaries.  PWM values range
-from 0 (off) to 255 (full speed).  Fan speed will be set to maximum when the
-temperature sensor associated with the PWM control exceeds
-pwm#_auto_point2_temp.
-
-The driver also allows control of the PWM frequency:
-
-* pwm1_freq
-
-The PWM frequency is rounded to the nearest one of:
-
-* 11.0 Hz
-* 14.7 Hz
-* 22.1 Hz
-* 29.4 Hz
-* 35.3 Hz
-* 44.1 Hz
-* 58.8 Hz
-* 88.2 Hz
-* 1.4 kHz
-* 22.5 kHz
-
-Notes
------
-
-The temperature inputs no longer need to be read periodically from userspace in
-order for the automatic pwm algorithm to run.  This was the case for earlier
-versions of the driver.