Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC cleanups from Olof Johansson:
 "This is the branch where we usually queue up cleanup efforts, moving
  drivers out of the architecture directory, header file restructuring,
  etc.  Sometimes they tangle with new development so it's hard to keep
  it strictly to cleanups.

  Some of the things included in this branch are:

   * Atmel SAMA5 conversion to common clock
   * Reset framework conversion for tegra platforms
    - Some of this depends on tegra clock driver reworks that are shared
      with Mike Turquette's clk tree.
   * Tegra DMA refactoring, which are shared branches with the DMA tree.
   * Removal of some header files on exynos to prepare for
     multiplatform"

* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
  ARM: mvebu: move Armada 370/XP specific definitions to armada-370-xp.h
  ARM: mvebu: remove prototypes of non-existing functions from common.h
  ARM: mvebu: move ARMADA_XP_MAX_CPUS to armada-370-xp.h
  serial: sh-sci: Rework baud rate calculation
  serial: sh-sci: Compute overrun_bit without using baud rate algo
  serial: sh-sci: Remove unused GPIO request code
  serial: sh-sci: Move overrun_bit and error_mask fields out of pdata
  serial: sh-sci: Support resources passed through platform resources
  serial: sh-sci: Don't check IRQ in verify port operation
  serial: sh-sci: Set the UPF_FIXED_PORT flag
  serial: sh-sci: Remove duplicate interrupt check in verify port op
  serial: sh-sci: Simplify baud rate calculation algorithms
  serial: sh-sci: Remove baud rate calculation algorithm 5
  serial: sh-sci: Sort headers alphabetically
  ARM: EXYNOS: Kill exynos_pm_late_initcall()
  ARM: EXYNOS: Consolidate selection of PM_GENERIC_DOMAINS for Exynos4
  ARM: at91: switch Calao QIL-A9260 board to DT
  clk: at91: fix pmc_clk_ids data type attriubte
  PM / devfreq: use inclusion <mach/map.h> instead of <plat/map-s5p.h>
  ARM: EXYNOS: remove <mach/regs-clock.h> for exynos
  ...

1 files changed, 185 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/at91-qil_a9260.dts b/arch/arm/boot/dts/at91-qil_a9260.dts
new file mode 100644
index 000000000000..5576ae8786c0
--- /dev/null
+++ b/arch/arm/boot/dts/at91-qil_a9260.dts
@@ -0,0 +1,185 @@
+/*
+ * at91-qil_a9260.dts - Device Tree file for Calao QIL A9260 board
+ *
+ * Copyright (C) 2011-2013 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ *
+ * Licensed under GPLv2.
+ */
+/dts-v1/;
+#include "at91sam9260.dtsi"
+/ {
+	model = "Calao QIL A9260";
+	compatible = "calao,qil-a9260", "atmel,at91sam9260", "atmel,at91sam9";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory {
+		reg = <0x20000000 0x4000000>;
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		main_clock: clock@0 {
+			compatible = "atmel,osc", "fixed-clock";
+			clock-frequency = <12000000>;
+		};
+	};
+
+	ahb {
+		apb {
+			usb1: gadget@fffa4000 {
+				atmel,vbus-gpio = <&pioC 5 GPIO_ACTIVE_HIGH>;
+				status = "okay";
+			};
+
+			mmc0: mmc@fffa8000 {
+				pinctrl-0 = <
+					&pinctrl_mmc0_clk
+					&pinctrl_mmc0_slot0_cmd_dat0
+					&pinctrl_mmc0_slot0_dat1_3>;
+				status = "okay";
+				slot@0 {
+					reg = <0>;
+					bus-width = <4>;
+				};
+			};
+
+			usart0: serial@fffb0000 {
+				pinctrl-0 =
+					<&pinctrl_usart0
+					 &pinctrl_usart0_rts
+					 &pinctrl_usart0_cts
+					 &pinctrl_usart0_dtr_dsr
+					 &pinctrl_usart0_dcd
+					 &pinctrl_usart0_ri>;
+				status = "okay";
+			};
+
+			usart1: serial@fffb4000 {
+				pinctrl-0 =
+					<&pinctrl_usart1
+					 &pinctrl_usart1_rts
+					 &pinctrl_usart1_cts>;
+				status = "okay";
+			};
+
+			usart2: serial@fffb8000 {
+				pinctrl-0 =
+					<&pinctrl_usart2
+					 &pinctrl_usart2_rts
+					 &pinctrl_usart2_cts>;
+				status = "okay";
+			};
+
+			macb0: ethernet@fffc4000 {
+				phy-mode = "rmii";
+				status = "okay";
+			};
+
+			spi0: spi@fffc8000 {
+				status = "okay";
+				cs-gpios = <&pioA 3 GPIO_ACTIVE_HIGH>;
+
+				m41t94@0 {
+					compatible = "st,m41t94";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+
+			};
+
+			dbgu: serial@fffff200 {
+				status = "okay";
+			};
+
+			shdwc@fffffd10 {
+				atmel,wakeup-counter = <10>;
+				atmel,wakeup-rtt-timer;
+			};
+		};
+
+		usb0: ohci@00500000 {
+			num-ports = <2>;
+			status = "okay";
+		};
+
+		nand0: nand@40000000 {
+			nand-bus-width = <8>;
+			nand-ecc-mode = "soft";
+			nand-on-flash-bbt;
+			status = "okay";
+
+			at91bootstrap@0 {
+				label = "at91bootstrap";
+				reg = <0x0 0x20000>;
+			};
+
+			barebox@20000 {
+				label = "barebox";
+				reg = <0x20000 0x40000>;
+			};
+
+			bareboxenv@60000 {
+				label = "bareboxenv";
+				reg = <0x60000 0x20000>;
+			};
+
+			bareboxenv2@80000 {
+				label = "bareboxenv2";
+				reg = <0x80000 0x20000>;
+			};
+
+			oftree@a0000 {
+				label = "oftree";
+				reg = <0xa0000 0x20000>;
+			};
+
+			kernel@c0000 {
+				label = "kernel";
+				reg = <0xc0000 0x400000>;
+			};
+
+			rootfs@4c0000 {
+				label = "rootfs";
+				reg = <0x4c0000 0x7800000>;
+			};
+
+			data@7cc0000 {
+				label = "data";
+				reg = <0x7cc0000 0x8340000>;
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		user_led {
+			label = "user_led";
+			gpios = <&pioB 21 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		user_pb {
+			label = "user_pb";
+			gpios = <&pioB 10 GPIO_ACTIVE_LOW>;
+			linux,code = <28>;
+			gpio-key,wakeup;
+		};
+	};
+
+	i2c@0 {
+		status = "okay";
+	};
+};