Merge tag 'arm-dt-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM DT updates from Arnd Bergmann:
 "There are 40 branches this time, adding a lot of new hardware support,
  and cleanups. Krzysztof Kozlowski continues his treewide cleanups.

  There are a number of new SoCs, all of them as part of existing
  families, and typically added along with a reference board:

   - Renesas RZ/G2UL (R9A07G043) is the single-core version of the
     RZ/G2L general-purpose MPU.

   - Renesas RZ/V2M (R9A09G011) is a smart camera SoC

   - Renesas R-Car V4H (R8A779G0) is an automotive chip with Cortex-A76
     cores and deep learning accerlation.

   - Broadcom BCM47622 is a new broadband SoC based on a quad Cortex-A7
     and dual Wifi-6.

   - Corstone1000 is a generic platform from Arm that is used for
     designing custom SoCs, the support for now is for the Fixed Virtual
     Platform emulation for it.

   - Mediatek MT8195 (Kompanio 1200) is a high-end consumer chip used in
     upcoming Chromebooks.

   - NXP i.MXRT1050 is a Cortex-M7 based microcontroller, the first
     MMU-less SoC to be added in a while

  New machines based on already supported SoCs this time are mainly for
  32-bit platforms and include:

   - Two wireless routers based on Broadcom bcm4708

   - 30 new boards based on NXP i.MX6, i.MX7 and i.MX8 families, mostly
     for the industrial embedded market, and on NXP LS1021A based IOT
     board.

   - Two ethernet switches based on Microchip LAN966

   - Eight Qualcomm Snapdragon based machines, including a smartwatch, a
     Chromebook board and some phones

   - Another phone based on the old ST-Ericsson Ux500 platform

   - Seven STM32MP1 based boards

   - Four single-board computers based on Rockchip RK3566/RK3568"

* tag 'arm-dt-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (791 commits)
  ARM: dts: kswitch-d10: enable networking
  ARM: dts: lan966x: add switch node
  ARM: dts: lan966x: add serdes node
  ARM: dts: lan966x: add reset switch reset node
  ARM: dts: lan966x: add MIIM nodes
  ARM: dts: lan966x: add hwmon node
  ARM: dts: lan966x: add basic Kontron KSwitch D10 support
  ARM: dts: lan966x: add flexcom I2C nodes
  ARM: dts: lan966x: add flexcom SPI nodes
  ARM: dts: lan966x: add all flexcom usart nodes
  ARM: dts: lan966x: add missing uart DMA channel
  ARM: dts: lan966x: add sgpio node
  ARM: dts: lan966x: swap dma channels for crypto node
  ARM: dts: lan966x: rename pinctrl nodes
  ARM: dts: at91: sama7g5: remove interrupt-parent from gic node
  ARM: dts: at91: use generic node name for dataflash
  ARM: dts: turris-omnia: Add atsha204a node
  arm64: dts: mt8192: Follow binding order for SCP registers
  arm64: dts: mediatek: add mtk-snfi for mt7622
  arm64: dts: mediatek: mt8195-demo: enable uart1
  ...

1 files changed, 0 insertions, 24 deletions

diff --git a/arch/arm64/boot/dts/renesas/rz-smarc-common.dtsi b/arch/arm64/boot/dts/renesas/rz-smarc-common.dtsi
index 588117aafaca..3962d47b3e59 100644
--- a/arch/arm64/boot/dts/renesas/rz-smarc-common.dtsi
+++ b/arch/arm64/boot/dts/renesas/rz-smarc-common.dtsi
@@ -26,7 +26,6 @@
 		serial0 = &scif0;
 		i2c0 = &i2c0;
 		i2c1 = &i2c1;
-		i2c3 = &i2c3;
 	};
 
 	chosen {
@@ -53,7 +52,6 @@
 			    "Mic Bias", "Microphone Jack";
 
 		cpu_dai: simple-audio-card,cpu {
-			sound-dai = <&ssi0>;
 		};
 
 		codec_dai: simple-audio-card,codec {
@@ -75,7 +73,6 @@
 		regulator-name = "SDHI1 VccQ";
 		regulator-min-microvolt = <1800000>;
 		regulator-max-microvolt = <3300000>;
-		gpios = <&pinctrl RZG2L_GPIO(39, 1) GPIO_ACTIVE_HIGH>;
 		gpios-states = <1>;
 		states = <3300000 1>, <1800000 0>;
 	};
@@ -131,20 +128,6 @@
 	status = "okay";
 };
 
-&i2c3 {
-	pinctrl-0 = <&i2c3_pins>;
-	pinctrl-names = "default";
-	clock-frequency = <400000>;
-
-	status = "okay";
-
-	wm8978: codec@1a {
-		compatible = "wlf,wm8978";
-		#sound-dai-cells = <0>;
-		reg = <0x1a>;
-	};
-};
-
 &ohci0 {
 	dr_mode = "otg";
 	status = "okay";
@@ -184,13 +167,6 @@
 	status = "okay";
 };
 
-&ssi0 {
-	pinctrl-0 = <&ssi0_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};
-
 &usb2_phy0 {
 	pinctrl-0 = <&usb0_pins>;
 	pinctrl-names = "default";