diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net/dsa/qca8k.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/net/dsa/qca8k.txt | 215 |
1 files changed, 0 insertions, 215 deletions
diff --git a/Documentation/devicetree/bindings/net/dsa/qca8k.txt b/Documentation/devicetree/bindings/net/dsa/qca8k.txt deleted file mode 100644 index 8c73f67c43ca..000000000000 --- a/Documentation/devicetree/bindings/net/dsa/qca8k.txt +++ /dev/null @@ -1,215 +0,0 @@ -* Qualcomm Atheros QCA8xxx switch family - -Required properties: - -- compatible: should be one of: - "qca,qca8327" - "qca,qca8334" - "qca,qca8337" - -- #size-cells: must be 0 -- #address-cells: must be 1 - -Optional properties: - -- reset-gpios: GPIO to be used to reset the whole device - -Subnodes: - -The integrated switch subnode should be specified according to the binding -described in dsa/dsa.txt. If the QCA8K switch is connect to a SoC's external -mdio-bus each subnode describing a port needs to have a valid phandle -referencing the internal PHY it is connected to. This is because there's no -N:N mapping of port and PHY id. -To declare the internal mdio-bus configuration, declare a mdio node in the -switch node and declare the phandle for the port referencing the internal -PHY is connected to. In this config a internal mdio-bus is registered and -the mdio MASTER is used as communication. - -Don't use mixed external and internal mdio-bus configurations, as this is -not supported by the hardware. - -The CPU port of this switch is always port 0. - -A CPU port node has the following optional node: - -- fixed-link : Fixed-link subnode describing a link to a non-MDIO - managed entity. See - Documentation/devicetree/bindings/net/fixed-link.txt - for details. - -For QCA8K the 'fixed-link' sub-node supports only the following properties: - -- 'speed' (integer, mandatory), to indicate the link speed. Accepted - values are 10, 100 and 1000 -- 'full-duplex' (boolean, optional), to indicate that full duplex is - used. When absent, half duplex is assumed. - -Examples: - -for the external mdio-bus configuration: - - &mdio0 { - phy_port1: phy@0 { - reg = <0>; - }; - - phy_port2: phy@1 { - reg = <1>; - }; - - phy_port3: phy@2 { - reg = <2>; - }; - - phy_port4: phy@3 { - reg = <3>; - }; - - phy_port5: phy@4 { - reg = <4>; - }; - - switch@10 { - compatible = "qca,qca8337"; - #address-cells = <1>; - #size-cells = <0>; - - reset-gpios = <&gpio 42 GPIO_ACTIVE_LOW>; - reg = <0x10>; - - ports { - #address-cells = <1>; - #size-cells = <0>; - port@0 { - reg = <0>; - label = "cpu"; - ethernet = <&gmac1>; - phy-mode = "rgmii"; - fixed-link { - speed = 1000; - full-duplex; - }; - }; - - port@1 { - reg = <1>; - label = "lan1"; - phy-handle = <&phy_port1>; - }; - - port@2 { - reg = <2>; - label = "lan2"; - phy-handle = <&phy_port2>; - }; - - port@3 { - reg = <3>; - label = "lan3"; - phy-handle = <&phy_port3>; - }; - - port@4 { - reg = <4>; - label = "lan4"; - phy-handle = <&phy_port4>; - }; - - port@5 { - reg = <5>; - label = "wan"; - phy-handle = <&phy_port5>; - }; - }; - }; - }; - -for the internal master mdio-bus configuration: - - &mdio0 { - switch@10 { - compatible = "qca,qca8337"; - #address-cells = <1>; - #size-cells = <0>; - - reset-gpios = <&gpio 42 GPIO_ACTIVE_LOW>; - reg = <0x10>; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - reg = <0>; - label = "cpu"; - ethernet = <&gmac1>; - phy-mode = "rgmii"; - fixed-link { - speed = 1000; - full-duplex; - }; - }; - - port@1 { - reg = <1>; - label = "lan1"; - phy-mode = "internal"; - phy-handle = <&phy_port1>; - }; - - port@2 { - reg = <2>; - label = "lan2"; - phy-mode = "internal"; - phy-handle = <&phy_port2>; - }; - - port@3 { - reg = <3>; - label = "lan3"; - phy-mode = "internal"; - phy-handle = <&phy_port3>; - }; - - port@4 { - reg = <4>; - label = "lan4"; - phy-mode = "internal"; - phy-handle = <&phy_port4>; - }; - - port@5 { - reg = <5>; - label = "wan"; - phy-mode = "internal"; - phy-handle = <&phy_port5>; - }; - }; - - mdio { - #address-cells = <1>; - #size-cells = <0>; - - phy_port1: phy@0 { - reg = <0>; - }; - - phy_port2: phy@1 { - reg = <1>; - }; - - phy_port3: phy@2 { - reg = <2>; - }; - - phy_port4: phy@3 { - reg = <3>; - }; - - phy_port5: phy@4 { - reg = <4>; - }; - }; - }; - }; |