diff options
Diffstat (limited to 'Documentation/hwmon/smsc47b397')
| -rw-r--r-- | Documentation/hwmon/smsc47b397 | 162 |
1 files changed, 98 insertions, 64 deletions
diff --git a/Documentation/hwmon/smsc47b397 b/Documentation/hwmon/smsc47b397 index 3a43b6948924..600194cf1804 100644 --- a/Documentation/hwmon/smsc47b397 +++ b/Documentation/hwmon/smsc47b397 @@ -2,29 +2,38 @@ Kernel driver smsc47b397 ======================== Supported chips: + * SMSC LPC47B397-NC + * SMSC SCH5307-NS + * SMSC SCH5317 + Prefix: 'smsc47b397' + Addresses scanned: none, address read from Super I/O config space + Datasheet: In this file -Authors: Mark M. Hoffman <mhoffman@lightlink.com> - Utilitek Systems, Inc. +Authors: + + - Mark M. Hoffman <mhoffman@lightlink.com> + - Utilitek Systems, Inc. November 23, 2004 -The following specification describes the SMSC LPC47B397-NC[1] sensor chip +The following specification describes the SMSC LPC47B397-NC [1]_ sensor chip (for which there is no public datasheet available). This document was provided by Craig Kelly (In-Store Broadcast Network) and edited/corrected by Mark M. Hoffman <mhoffman@lightlink.com>. -[1] And SMSC SCH5307-NS and SCH5317, which have different device IDs but are -otherwise compatible. +.. [1] And SMSC SCH5307-NS and SCH5317, which have different device IDs but are + otherwise compatible. -* * * * * +------------------------------------------------------------------------- -Methods for detecting the HP SIO and reading the thermal data on a dc7100. +Methods for detecting the HP SIO and reading the thermal data on a dc7100 +------------------------------------------------------------------------- The thermal information on the dc7100 is contained in the SIO Hardware Monitor (HWM). The information is accessed through an index/data pair. The index/data @@ -35,18 +44,22 @@ and 0x61 (LSB). Currently we are using 0x480 for the HWM Base Address and Reading temperature information. The temperature information is located in the following registers: + +=============== ======= ======================================================= Temp1 0x25 (Currently, this reflects the CPU temp on all systems). Temp2 0x26 Temp3 0x27 Temp4 0x80 +=============== ======= ======================================================= Programming Example -The following is an example of how to read the HWM temperature registers: -MOV DX,480H -MOV AX,25H -OUT DX,AL -MOV DX,481H -IN AL,DX +The following is an example of how to read the HWM temperature registers:: + + MOV DX,480H + MOV AX,25H + OUT DX,AL + MOV DX,481H + IN AL,DX AL contains the data in hex, the temperature in Celsius is the decimal equivalent. @@ -55,25 +68,32 @@ Ex: If AL contains 0x2A, the temperature is 42 degrees C. Reading tach information. The fan speed information is located in the following registers: + +=============== ======= ======= ================================= LSB MSB Tach1 0x28 0x29 (Currently, this reflects the CPU fan speed on all systems). Tach2 0x2A 0x2B Tach3 0x2C 0x2D Tach4 0x2E 0x2F +=============== ======= ======= ================================= -Important!!! -Reading the tach LSB locks the tach MSB. -The LSB Must be read first. +.. Important:: + + Reading the tach LSB locks the tach MSB. + The LSB Must be read first. + +How to convert the tach reading to RPM +-------------------------------------- -How to convert the tach reading to RPM. The tach reading (TCount) is given by: (Tach MSB * 256) + (Tach LSB) The SIO counts the number of 90kHz (11.111us) pulses per revolution. RPM = 60/(TCount * 11.111us) -Example: -Reg 0x28 = 0x9B -Reg 0x29 = 0x08 +Example:: + + Reg 0x28 = 0x9B + Reg 0x29 = 0x08 TCount = 0x89B = 2203 @@ -81,21 +101,28 @@ RPM = 60 / (2203 * 11.11111 E-6) = 2451 RPM Obtaining the SIO version. -CONFIGURATION SEQUENCE +Configuration Sequence +---------------------- + To program the configuration registers, the following sequence must be followed: 1. Enter Configuration Mode 2. Configure the Configuration Registers 3. Exit Configuration Mode. Enter Configuration Mode +^^^^^^^^^^^^^^^^^^^^^^^^ + To place the chip into the Configuration State The config key (0x55) is written to the CONFIG PORT (0x2E). Configuration Mode +^^^^^^^^^^^^^^^^^^ + In configuration mode, the INDEX PORT is located at the CONFIG PORT address and the DATA PORT is at INDEX PORT address + 1. The desired configuration registers are accessed in two steps: + a. Write the index of the Logical Device Number Configuration Register (i.e., 0x07) to the INDEX PORT and then write the number of the desired logical device to the DATA PORT. @@ -104,30 +131,35 @@ b. Write the address of the desired configuration register within the logical device to the INDEX PORT and then write or read the config- uration register through the DATA PORT. -Note: If accessing the Global Configuration Registers, step (a) is not required. +Note: + If accessing the Global Configuration Registers, step (a) is not required. Exit Configuration Mode +^^^^^^^^^^^^^^^^^^^^^^^ + To exit the Configuration State the write 0xAA to the CONFIG PORT (0x2E). The chip returns to the RUN State. (This is important). Programming Example -The following is an example of how to read the SIO Device ID located at 0x20 - -; ENTER CONFIGURATION MODE -MOV DX,02EH -MOV AX,055H -OUT DX,AL -; GLOBAL CONFIGURATION REGISTER -MOV DX,02EH -MOV AL,20H -OUT DX,AL -; READ THE DATA -MOV DX,02FH -IN AL,DX -; EXIT CONFIGURATION MODE -MOV DX,02EH -MOV AX,0AAH -OUT DX,AL +^^^^^^^^^^^^^^^^^^^ + +The following is an example of how to read the SIO Device ID located at 0x20: + + ; ENTER CONFIGURATION MODE + MOV DX,02EH + MOV AX,055H + OUT DX,AL + ; GLOBAL CONFIGURATION REGISTER + MOV DX,02EH + MOV AL,20H + OUT DX,AL + ; READ THE DATA + MOV DX,02FH + IN AL,DX + ; EXIT CONFIGURATION MODE + MOV DX,02EH + MOV AX,0AAH + OUT DX,AL The registers of interest for identifying the SIO on the dc7100 are Device ID (0x20) and Device Rev (0x21). @@ -135,29 +167,31 @@ The registers of interest for identifying the SIO on the dc7100 are Device ID The Device ID will read 0x6F (0x81 for SCH5307-NS, and 0x85 for SCH5317) The Device Rev currently reads 0x01 -Obtaining the HWM Base Address. +Obtaining the HWM Base Address +------------------------------ + The following is an example of how to read the HWM Base Address located in -Logical Device 8. - -; ENTER CONFIGURATION MODE -MOV DX,02EH -MOV AX,055H -OUT DX,AL -; CONFIGURE REGISTER CRE0, -; LOGICAL DEVICE 8 -MOV DX,02EH -MOV AL,07H -OUT DX,AL ;Point to LD# Config Reg -MOV DX,02FH -MOV AL, 08H -OUT DX,AL;Point to Logical Device 8 -; -MOV DX,02EH -MOV AL,60H -OUT DX,AL ; Point to HWM Base Addr MSB -MOV DX,02FH -IN AL,DX ; Get MSB of HWM Base Addr -; EXIT CONFIGURATION MODE -MOV DX,02EH -MOV AX,0AAH -OUT DX,AL +Logical Device 8:: + + ; ENTER CONFIGURATION MODE + MOV DX,02EH + MOV AX,055H + OUT DX,AL + ; CONFIGURE REGISTER CRE0, + ; LOGICAL DEVICE 8 + MOV DX,02EH + MOV AL,07H + OUT DX,AL ;Point to LD# Config Reg + MOV DX,02FH + MOV AL, 08H + OUT DX,AL;Point to Logical Device 8 + ; + MOV DX,02EH + MOV AL,60H + OUT DX,AL ; Point to HWM Base Addr MSB + MOV DX,02FH + IN AL,DX ; Get MSB of HWM Base Addr + ; EXIT CONFIGURATION MODE + MOV DX,02EH + MOV AX,0AAH + OUT DX,AL |