diff options
Diffstat (limited to 'arch/riscv/boot')
-rw-r--r-- | arch/riscv/boot/dts/Makefile | 1 | ||||
-rw-r--r-- | arch/riscv/boot/dts/canaan/Makefile | 4 | ||||
-rw-r--r-- | arch/riscv/boot/dts/canaan/k210.dtsi | 23 | ||||
-rw-r--r-- | arch/riscv/boot/dts/canaan/sipeed_maix_bit.dts | 2 | ||||
-rw-r--r-- | arch/riscv/boot/dts/canaan/sipeed_maix_dock.dts | 2 | ||||
-rw-r--r-- | arch/riscv/boot/dts/canaan/sipeed_maix_go.dts | 2 | ||||
-rw-r--r-- | arch/riscv/boot/dts/canaan/sipeed_maixduino.dts | 2 | ||||
-rw-r--r-- | arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts | 4 | ||||
-rw-r--r-- | arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi | 60 | ||||
-rw-r--r-- | arch/riscv/boot/dts/sifive/fu540-c000.dtsi | 40 | ||||
-rw-r--r-- | arch/riscv/boot/dts/sifive/fu740-c000.dtsi | 14 | ||||
-rw-r--r-- | arch/riscv/boot/dts/sifive/hifive-unleashed-a00.dts | 1 | ||||
-rw-r--r-- | arch/riscv/boot/dts/sifive/hifive-unmatched-a00.dts | 118 | ||||
-rw-r--r-- | arch/riscv/boot/dts/starfive/Makefile | 2 | ||||
-rw-r--r-- | arch/riscv/boot/dts/starfive/jh7100-beaglev-starlight.dts | 164 | ||||
-rw-r--r-- | arch/riscv/boot/dts/starfive/jh7100.dtsi | 230 |
16 files changed, 529 insertions, 140 deletions
diff --git a/arch/riscv/boot/dts/Makefile b/arch/riscv/boot/dts/Makefile index fe996b88319e..ff174996cdfd 100644 --- a/arch/riscv/boot/dts/Makefile +++ b/arch/riscv/boot/dts/Makefile @@ -1,5 +1,6 @@ # SPDX-License-Identifier: GPL-2.0 subdir-y += sifive +subdir-y += starfive subdir-$(CONFIG_SOC_CANAAN_K210_DTB_BUILTIN) += canaan subdir-y += microchip diff --git a/arch/riscv/boot/dts/canaan/Makefile b/arch/riscv/boot/dts/canaan/Makefile index 9ee7156c0c31..c61b08ac8554 100644 --- a/arch/riscv/boot/dts/canaan/Makefile +++ b/arch/riscv/boot/dts/canaan/Makefile @@ -1,5 +1,3 @@ # SPDX-License-Identifier: GPL-2.0 -ifneq ($(CONFIG_SOC_CANAAN_K210_DTB_SOURCE),"") -dtb-y += $(strip $(shell echo $(CONFIG_SOC_CANAAN_K210_DTB_SOURCE))).dtb +dtb-$(CONFIG_SOC_CANAAN_K210_DTB_BUILTIN) += $(addsuffix .dtb, $(CONFIG_SOC_CANAAN_K210_DTB_SOURCE)) obj-$(CONFIG_SOC_CANAAN_K210_DTB_BUILTIN) += $(addsuffix .o, $(dtb-y)) -endif diff --git a/arch/riscv/boot/dts/canaan/k210.dtsi b/arch/riscv/boot/dts/canaan/k210.dtsi index 5e8ca8142482..56f57118c633 100644 --- a/arch/riscv/boot/dts/canaan/k210.dtsi +++ b/arch/riscv/boot/dts/canaan/k210.dtsi @@ -103,8 +103,8 @@ clint0: timer@2000000 { compatible = "canaan,k210-clint", "sifive,clint0"; reg = <0x2000000 0xC000>; - interrupts-extended = <&cpu0_intc 3 &cpu0_intc 7 - &cpu1_intc 3 &cpu1_intc 7>; + interrupts-extended = <&cpu0_intc 3>, <&cpu0_intc 7>, + <&cpu1_intc 3>, <&cpu1_intc 7>; }; plic0: interrupt-controller@c000000 { @@ -113,7 +113,7 @@ compatible = "canaan,k210-plic", "sifive,plic-1.0.0"; reg = <0xC000000 0x4000000>; interrupt-controller; - interrupts-extended = <&cpu0_intc 11 &cpu1_intc 11>; + interrupts-extended = <&cpu0_intc 11>, <&cpu1_intc 11>; riscv,ndev = <65>; }; @@ -130,10 +130,11 @@ compatible = "canaan,k210-gpiohs", "sifive,gpio0"; reg = <0x38001000 0x1000>; interrupt-controller; - interrupts = <34 35 36 37 38 39 40 41 - 42 43 44 45 46 47 48 49 - 50 51 52 53 54 55 56 57 - 58 59 60 61 62 63 64 65>; + interrupts = <34>, <35>, <36>, <37>, <38>, <39>, <40>, + <41>, <42>, <43>, <44>, <45>, <46>, <47>, + <48>, <49>, <50>, <51>, <52>, <53>, <54>, + <55>, <56>, <57>, <58>, <59>, <60>, <61>, + <62>, <63>, <64>, <65>; gpio-controller; ngpios = <32>; }; @@ -141,7 +142,7 @@ dmac0: dma-controller@50000000 { compatible = "snps,axi-dma-1.01a"; reg = <0x50000000 0x1000>; - interrupts = <27 28 29 30 31 32>; + interrupts = <27>, <28>, <29>, <30>, <31>, <32>; #dma-cells = <1>; clocks = <&sysclk K210_CLK_DMA>, <&sysclk K210_CLK_DMA>; clock-names = "core-clk", "cfgr-clk"; @@ -316,7 +317,7 @@ timer0: timer@502d0000 { compatible = "snps,dw-apb-timer"; reg = <0x502D0000 0x100>; - interrupts = <14 15>; + interrupts = <14>, <15>; clocks = <&sysclk K210_CLK_TIMER0>, <&sysclk K210_CLK_APB0>; clock-names = "timer", "pclk"; @@ -326,7 +327,7 @@ timer1: timer@502e0000 { compatible = "snps,dw-apb-timer"; reg = <0x502E0000 0x100>; - interrupts = <16 17>; + interrupts = <16>, <17>; clocks = <&sysclk K210_CLK_TIMER1>, <&sysclk K210_CLK_APB0>; clock-names = "timer", "pclk"; @@ -336,7 +337,7 @@ timer2: timer@502f0000 { compatible = "snps,dw-apb-timer"; reg = <0x502F0000 0x100>; - interrupts = <18 19>; + interrupts = <18>, <19>; clocks = <&sysclk K210_CLK_TIMER2>, <&sysclk K210_CLK_APB0>; clock-names = "timer", "pclk"; diff --git a/arch/riscv/boot/dts/canaan/sipeed_maix_bit.dts b/arch/riscv/boot/dts/canaan/sipeed_maix_bit.dts index 0bcaf35045e7..984872f3d3a9 100644 --- a/arch/riscv/boot/dts/canaan/sipeed_maix_bit.dts +++ b/arch/riscv/boot/dts/canaan/sipeed_maix_bit.dts @@ -199,7 +199,7 @@ }; &spi3 { - spi-flash@0 { + flash@0 { compatible = "jedec,spi-nor"; reg = <0>; spi-max-frequency = <50000000>; diff --git a/arch/riscv/boot/dts/canaan/sipeed_maix_dock.dts b/arch/riscv/boot/dts/canaan/sipeed_maix_dock.dts index ac8a03f5867a..7ba99b4da304 100644 --- a/arch/riscv/boot/dts/canaan/sipeed_maix_dock.dts +++ b/arch/riscv/boot/dts/canaan/sipeed_maix_dock.dts @@ -201,7 +201,7 @@ }; &spi3 { - spi-flash@0 { + flash@0 { compatible = "jedec,spi-nor"; reg = <0>; spi-max-frequency = <50000000>; diff --git a/arch/riscv/boot/dts/canaan/sipeed_maix_go.dts b/arch/riscv/boot/dts/canaan/sipeed_maix_go.dts index 623998194bc1..be9b12c9b374 100644 --- a/arch/riscv/boot/dts/canaan/sipeed_maix_go.dts +++ b/arch/riscv/boot/dts/canaan/sipeed_maix_go.dts @@ -209,7 +209,7 @@ }; &spi3 { - spi-flash@0 { + flash@0 { compatible = "jedec,spi-nor"; reg = <0>; spi-max-frequency = <50000000>; diff --git a/arch/riscv/boot/dts/canaan/sipeed_maixduino.dts b/arch/riscv/boot/dts/canaan/sipeed_maixduino.dts index cf605ba0d67e..031c0c28f819 100644 --- a/arch/riscv/boot/dts/canaan/sipeed_maixduino.dts +++ b/arch/riscv/boot/dts/canaan/sipeed_maixduino.dts @@ -174,7 +174,7 @@ }; &spi3 { - spi-flash@0 { + flash@0 { compatible = "jedec,spi-nor"; reg = <0>; spi-max-frequency = <50000000>; diff --git a/arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts b/arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts index fc1e5869df1b..0c748ae1b006 100644 --- a/arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts +++ b/arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts @@ -35,6 +35,10 @@ }; }; +&refclk { + clock-frequency = <600000000>; +}; + &serial0 { status = "okay"; }; diff --git a/arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi b/arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi index c9f6d205d2ba..869aaf0d5c06 100644 --- a/arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi +++ b/arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi @@ -9,9 +9,6 @@ model = "Microchip PolarFire SoC"; compatible = "microchip,mpfs"; - chosen { - }; - cpus { #address-cells = <1>; #size-cells = <0>; @@ -142,6 +139,11 @@ }; }; + refclk: msspllclk { + compatible = "fixed-clock"; + #clock-cells = <0>; + }; + soc { #address-cells = <2>; #size-cells = <2>; @@ -156,62 +158,48 @@ cache-size = <2097152>; cache-unified; interrupt-parent = <&plic>; - interrupts = <1 2 3>; + interrupts = <1>, <2>, <3>; reg = <0x0 0x2010000 0x0 0x1000>; }; clint@2000000 { compatible = "sifive,fu540-c000-clint", "sifive,clint0"; reg = <0x0 0x2000000 0x0 0xC000>; - interrupts-extended = <&cpu0_intc 3 &cpu0_intc 7 - &cpu1_intc 3 &cpu1_intc 7 - &cpu2_intc 3 &cpu2_intc 7 - &cpu3_intc 3 &cpu3_intc 7 - &cpu4_intc 3 &cpu4_intc 7>; + interrupts-extended = <&cpu0_intc 3>, <&cpu0_intc 7>, + <&cpu1_intc 3>, <&cpu1_intc 7>, + <&cpu2_intc 3>, <&cpu2_intc 7>, + <&cpu3_intc 3>, <&cpu3_intc 7>, + <&cpu4_intc 3>, <&cpu4_intc 7>; }; plic: interrupt-controller@c000000 { - #interrupt-cells = <1>; compatible = "sifive,fu540-c000-plic", "sifive,plic-1.0.0"; reg = <0x0 0xc000000 0x0 0x4000000>; - riscv,ndev = <186>; + #address-cells = <0>; + #interrupt-cells = <1>; interrupt-controller; - interrupts-extended = <&cpu0_intc 11 - &cpu1_intc 11 &cpu1_intc 9 - &cpu2_intc 11 &cpu2_intc 9 - &cpu3_intc 11 &cpu3_intc 9 - &cpu4_intc 11 &cpu4_intc 9>; + interrupts-extended = <&cpu0_intc 11>, + <&cpu1_intc 11>, <&cpu1_intc 9>, + <&cpu2_intc 11>, <&cpu2_intc 9>, + <&cpu3_intc 11>, <&cpu3_intc 9>, + <&cpu4_intc 11>, <&cpu4_intc 9>; + riscv,ndev = <186>; }; dma@3000000 { compatible = "sifive,fu540-c000-pdma"; reg = <0x0 0x3000000 0x0 0x8000>; interrupt-parent = <&plic>; - interrupts = <23 24 25 26 27 28 29 30>; + interrupts = <23>, <24>, <25>, <26>, <27>, <28>, <29>, + <30>; #dma-cells = <1>; }; - refclk: refclk { - compatible = "fixed-clock"; - #clock-cells = <0>; - clock-frequency = <600000000>; - clock-output-names = "msspllclk"; - }; - clkcfg: clkcfg@20002000 { compatible = "microchip,mpfs-clkcfg"; reg = <0x0 0x20002000 0x0 0x1000>; - reg-names = "mss_sysreg"; clocks = <&refclk>; #clock-cells = <1>; - clock-output-names = "cpu", "axi", "ahb", "envm", /* 0-3 */ - "mac0", "mac1", "mmc", "timer", /* 4-7 */ - "mmuart0", "mmuart1", "mmuart2", "mmuart3", /* 8-11 */ - "mmuart4", "spi0", "spi1", "i2c0", /* 12-15 */ - "i2c1", "can0", "can1", "usb", /* 16-19 */ - "rsvd", "rtc", "qspi", "gpio0", /* 20-23 */ - "gpio1", "gpio2", "ddrc", "fic0", /* 24-27 */ - "fic1", "fic2", "fic3", "athena", "cfm"; /* 28-32 */ }; serial0: serial@20000000 { @@ -267,7 +255,7 @@ compatible = "microchip,mpfs-sd4hc", "cdns,sd4hc"; reg = <0x0 0x20008000 0x0 0x1000>; interrupt-parent = <&plic>; - interrupts = <88 89>; + interrupts = <88>, <89>; clocks = <&clkcfg 6>; max-frequency = <200000000>; status = "disabled"; @@ -277,7 +265,7 @@ compatible = "cdns,macb"; reg = <0x0 0x20110000 0x0 0x2000>; interrupt-parent = <&plic>; - interrupts = <64 65 66 67>; + interrupts = <64>, <65>, <66>, <67>; local-mac-address = [00 00 00 00 00 00]; clocks = <&clkcfg 4>, <&clkcfg 2>; clock-names = "pclk", "hclk"; @@ -290,7 +278,7 @@ compatible = "cdns,macb"; reg = <0x0 0x20112000 0x0 0x2000>; interrupt-parent = <&plic>; - interrupts = <70 71 72 73>; + interrupts = <70>, <71>, <72>, <73>; local-mac-address = [00 00 00 00 00 00]; clocks = <&clkcfg 5>, <&clkcfg 2>; status = "disabled"; diff --git a/arch/riscv/boot/dts/sifive/fu540-c000.dtsi b/arch/riscv/boot/dts/sifive/fu540-c000.dtsi index 0655b5c4201d..3eef52b1a59b 100644 --- a/arch/riscv/boot/dts/sifive/fu540-c000.dtsi +++ b/arch/riscv/boot/dts/sifive/fu540-c000.dtsi @@ -137,20 +137,21 @@ soc { #address-cells = <2>; #size-cells = <2>; - compatible = "sifive,fu540-c000", "sifive,fu540", "simple-bus"; + compatible = "simple-bus"; ranges; plic0: interrupt-controller@c000000 { - #interrupt-cells = <1>; compatible = "sifive,fu540-c000-plic", "sifive,plic-1.0.0"; reg = <0x0 0xc000000 0x0 0x4000000>; - riscv,ndev = <53>; + #address-cells = <0>; + #interrupt-cells = <1>; interrupt-controller; - interrupts-extended = < - &cpu0_intc 0xffffffff - &cpu1_intc 0xffffffff &cpu1_intc 9 - &cpu2_intc 0xffffffff &cpu2_intc 9 - &cpu3_intc 0xffffffff &cpu3_intc 9 - &cpu4_intc 0xffffffff &cpu4_intc 9>; + interrupts-extended = + <&cpu0_intc 0xffffffff>, + <&cpu1_intc 0xffffffff>, <&cpu1_intc 9>, + <&cpu2_intc 0xffffffff>, <&cpu2_intc 9>, + <&cpu3_intc 0xffffffff>, <&cpu3_intc 9>, + <&cpu4_intc 0xffffffff>, <&cpu4_intc 9>; + riscv,ndev = <53>; }; prci: clock-controller@10000000 { compatible = "sifive,fu540-c000-prci"; @@ -170,7 +171,8 @@ compatible = "sifive,fu540-c000-pdma"; reg = <0x0 0x3000000 0x0 0x8000>; interrupt-parent = <&plic0>; - interrupts = <23 24 25 26 27 28 29 30>; + interrupts = <23>, <24>, <25>, <26>, <27>, <28>, <29>, + <30>; #dma-cells = <1>; }; uart1: serial@10011000 { @@ -195,8 +197,8 @@ }; qspi0: spi@10040000 { compatible = "sifive,fu540-c000-spi", "sifive,spi0"; - reg = <0x0 0x10040000 0x0 0x1000 - 0x0 0x20000000 0x0 0x10000000>; + reg = <0x0 0x10040000 0x0 0x1000>, + <0x0 0x20000000 0x0 0x10000000>; interrupt-parent = <&plic0>; interrupts = <51>; clocks = <&prci PRCI_CLK_TLCLK>; @@ -206,8 +208,8 @@ }; qspi1: spi@10041000 { compatible = "sifive,fu540-c000-spi", "sifive,spi0"; - reg = <0x0 0x10041000 0x0 0x1000 - 0x0 0x30000000 0x0 0x10000000>; + reg = <0x0 0x10041000 0x0 0x1000>, + <0x0 0x30000000 0x0 0x10000000>; interrupt-parent = <&plic0>; interrupts = <52>; clocks = <&prci PRCI_CLK_TLCLK>; @@ -229,8 +231,8 @@ compatible = "sifive,fu540-c000-gem"; interrupt-parent = <&plic0>; interrupts = <53>; - reg = <0x0 0x10090000 0x0 0x2000 - 0x0 0x100a0000 0x0 0x1000>; + reg = <0x0 0x10090000 0x0 0x2000>, + <0x0 0x100a0000 0x0 0x1000>; local-mac-address = [00 00 00 00 00 00]; clock-names = "pclk", "hclk"; clocks = <&prci PRCI_CLK_GEMGXLPLL>, @@ -243,7 +245,7 @@ compatible = "sifive,fu540-c000-pwm", "sifive,pwm0"; reg = <0x0 0x10020000 0x0 0x1000>; interrupt-parent = <&plic0>; - interrupts = <42 43 44 45>; + interrupts = <42>, <43>, <44>, <45>; clocks = <&prci PRCI_CLK_TLCLK>; #pwm-cells = <3>; status = "disabled"; @@ -252,7 +254,7 @@ compatible = "sifive,fu540-c000-pwm", "sifive,pwm0"; reg = <0x0 0x10021000 0x0 0x1000>; interrupt-parent = <&plic0>; - interrupts = <46 47 48 49>; + interrupts = <46>, <47>, <48>, <49>; clocks = <&prci PRCI_CLK_TLCLK>; #pwm-cells = <3>; status = "disabled"; @@ -265,7 +267,7 @@ cache-size = <2097152>; cache-unified; interrupt-parent = <&plic0>; - interrupts = <1 2 3>; + interrupts = <1>, <2>, <3>; reg = <0x0 0x2010000 0x0 0x1000>; }; gpio: gpio@10060000 { diff --git a/arch/riscv/boot/dts/sifive/fu740-c000.dtsi b/arch/riscv/boot/dts/sifive/fu740-c000.dtsi index abbb960f90a0..8464b0e3c887 100644 --- a/arch/riscv/boot/dts/sifive/fu740-c000.dtsi +++ b/arch/riscv/boot/dts/sifive/fu740-c000.dtsi @@ -147,12 +147,12 @@ reg = <0x0 0xc000000 0x0 0x4000000>; riscv,ndev = <69>; interrupt-controller; - interrupts-extended = < - &cpu0_intc 0xffffffff - &cpu1_intc 0xffffffff &cpu1_intc 9 - &cpu2_intc 0xffffffff &cpu2_intc 9 - &cpu3_intc 0xffffffff &cpu3_intc 9 - &cpu4_intc 0xffffffff &cpu4_intc 9>; + interrupts-extended = + <&cpu0_intc 0xffffffff>, + <&cpu1_intc 0xffffffff>, <&cpu1_intc 9>, + <&cpu2_intc 0xffffffff>, <&cpu2_intc 9>, + <&cpu3_intc 0xffffffff>, <&cpu3_intc 9>, + <&cpu4_intc 0xffffffff>, <&cpu4_intc 9>; }; prci: clock-controller@10000000 { compatible = "sifive,fu740-c000-prci"; @@ -273,7 +273,7 @@ cache-size = <2097152>; cache-unified; interrupt-parent = <&plic0>; - interrupts = <19 21 22 20>; + interrupts = <19>, <21>, <22>, <20>; reg = <0x0 0x2010000 0x0 0x1000>; }; gpio: gpio@10060000 { diff --git a/arch/riscv/boot/dts/sifive/hifive-unleashed-a00.dts b/arch/riscv/boot/dts/sifive/hifive-unleashed-a00.dts index ba304d4c455c..ced0d4e47938 100644 --- a/arch/riscv/boot/dts/sifive/hifive-unleashed-a00.dts +++ b/arch/riscv/boot/dts/sifive/hifive-unleashed-a00.dts @@ -76,6 +76,7 @@ spi-max-frequency = <20000000>; voltage-ranges = <3300 3300>; disable-wp; + gpios = <&gpio 11 GPIO_ACTIVE_LOW>; }; }; diff --git a/arch/riscv/boot/dts/sifive/hifive-unmatched-a00.dts b/arch/riscv/boot/dts/sifive/hifive-unmatched-a00.dts index 4f66919215f6..c4ed9efdff03 100644 --- a/arch/riscv/boot/dts/sifive/hifive-unmatched-a00.dts +++ b/arch/riscv/boot/dts/sifive/hifive-unmatched-a00.dts @@ -2,6 +2,7 @@ /* Copyright (c) 2020 SiFive, Inc */ #include "fu740-c000.dtsi" +#include <dt-bindings/gpio/gpio.h> #include <dt-bindings/interrupt-controller/irq.h> /* Clock frequency (in Hz) of the PCB crystal for rtcclk */ @@ -38,6 +39,11 @@ clock-frequency = <RTCCLK_FREQ>; clock-output-names = "rtcclk"; }; + + gpio-poweroff { + compatible = "gpio-poweroff"; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + }; }; &uart0 { @@ -54,10 +60,21 @@ temperature-sensor@4c { compatible = "ti,tmp451"; reg = <0x4c>; + vcc-supply = <&vdd_bpro>; interrupt-parent = <&gpio>; interrupts = <6 IRQ_TYPE_LEVEL_LOW>; }; + eeprom@54 { + compatible = "microchip,24c02", "atmel,24c02"; + reg = <0x54>; + vcc-supply = <&vdd_bpro>; + label = "board-id"; + pagesize = <16>; + read-only; + size = <256>; + }; + pmic@58 { compatible = "dlg,da9063"; reg = <0x58>; @@ -65,48 +82,44 @@ interrupts = <1 IRQ_TYPE_LEVEL_LOW>; interrupt-controller; - regulators { - vdd_bcore1: bcore1 { - regulator-min-microvolt = <900000>; - regulator-max-microvolt = <900000>; - regulator-min-microamp = <5000000>; - regulator-max-microamp = <5000000>; - regulator-always-on; - }; + onkey { + compatible = "dlg,da9063-onkey"; + }; + + rtc { + compatible = "dlg,da9063-rtc"; + }; - vdd_bcore2: bcore2 { - regulator-min-microvolt = <900000>; - regulator-max-microvolt = <900000>; - regulator-min-microamp = <5000000>; - regulator-max-microamp = <5000000>; + wdt { + compatible = "dlg,da9063-watchdog"; + }; + + regulators { + vdd_bcore: bcores-merged { + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + regulator-min-microamp = <4800000>; + regulator-max-microamp = <4800000>; regulator-always-on; }; vdd_bpro: bpro { regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; - regulator-min-microamp = <2500000>; - regulator-max-microamp = <2500000>; + regulator-min-microamp = <2400000>; + regulator-max-microamp = <2400000>; regulator-always-on; }; vdd_bperi: bperi { - regulator-min-microvolt = <1050000>; - regulator-max-microvolt = <1050000>; + regulator-min-microvolt = <1060000>; + regulator-max-microvolt = <1060000>; regulator-min-microamp = <1500000>; regulator-max-microamp = <1500000>; regulator-always-on; }; - vdd_bmem: bmem { - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1200000>; - regulator-min-microamp = <3000000>; - regulator-max-microamp = <3000000>; - regulator-always-on; - }; - - vdd_bio: bio { + vdd_bmem_bio: bmem-bio-merged { regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; regulator-min-microamp = <3000000>; @@ -117,86 +130,66 @@ vdd_ldo1: ldo1 { regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; - regulator-min-microamp = <100000>; - regulator-max-microamp = <100000>; regulator-always-on; }; vdd_ldo2: ldo2 { regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; - regulator-min-microamp = <200000>; - regulator-max-microamp = <200000>; regulator-always-on; }; vdd_ldo3: ldo3 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-min-microamp = <200000>; - regulator-max-microamp = <200000>; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; regulator-always-on; }; vdd_ldo4: ldo4 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-min-microamp = <200000>; - regulator-max-microamp = <200000>; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; regulator-always-on; }; vdd_ldo5: ldo5 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-min-microamp = <100000>; - regulator-max-microamp = <100000>; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; regulator-always-on; }; vdd_ldo6: ldo6 { - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-min-microamp = <200000>; - regulator-max-microamp = <200000>; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; regulator-always-on; }; vdd_ldo7: ldo7 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-min-microamp = <200000>; - regulator-max-microamp = <200000>; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; regulator-always-on; }; vdd_ldo8: ldo8 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-min-microamp = <200000>; - regulator-max-microamp = <200000>; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; regulator-always-on; }; vdd_ld09: ldo9 { regulator-min-microvolt = <1050000>; regulator-max-microvolt = <1050000>; - regulator-min-microamp = <200000>; - regulator-max-microamp = <200000>; + regulator-always-on; }; vdd_ldo10: ldo10 { regulator-min-microvolt = <1000000>; regulator-max-microvolt = <1000000>; - regulator-min-microamp = <300000>; - regulator-max-microamp = <300000>; + regulator-always-on; }; vdd_ldo11: ldo11 { regulator-min-microvolt = <2500000>; regulator-max-microvolt = <2500000>; - regulator-min-microamp = <300000>; - regulator-max-microamp = <300000>; regulator-always-on; }; }; @@ -223,6 +216,7 @@ spi-max-frequency = <20000000>; voltage-ranges = <3300 3300>; disable-wp; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; }; }; @@ -245,4 +239,8 @@ &gpio { status = "okay"; + gpio-line-names = "J29.1", "PMICNTB", "PMICSHDN", "J8.1", "J8.3", + "PCIe_PWREN", "THERM", "UBRDG_RSTN", "PCIe_PERSTN", + "ULPI_RSTN", "J8.2", "UHUB_RSTN", "GEMGXL_RST", "J8.4", + "EN_VDD_SD", "SD_CD"; }; diff --git a/arch/riscv/boot/dts/starfive/Makefile b/arch/riscv/boot/dts/starfive/Makefile new file mode 100644 index 000000000000..0ea1bc15ab30 --- /dev/null +++ b/arch/riscv/boot/dts/starfive/Makefile @@ -0,0 +1,2 @@ +# SPDX-License-Identifier: GPL-2.0 +dtb-$(CONFIG_SOC_STARFIVE) += jh7100-beaglev-starlight.dtb diff --git a/arch/riscv/boot/dts/starfive/jh7100-beaglev-starlight.dts b/arch/riscv/boot/dts/starfive/jh7100-beaglev-starlight.dts new file mode 100644 index 000000000000..c9af67f7a0d2 --- /dev/null +++ b/arch/riscv/boot/dts/starfive/jh7100-beaglev-starlight.dts @@ -0,0 +1,164 @@ +// SPDX-License-Identifier: GPL-2.0 OR MIT +/* + * Copyright (C) 2021 StarFive Technology Co., Ltd. + * Copyright (C) 2021 Emil Renner Berthing <kernel@esmil.dk> + */ + +/dts-v1/; +#include "jh7100.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/pinctrl/pinctrl-starfive.h> + +/ { + model = "BeagleV Starlight Beta"; + compatible = "beagle,beaglev-starlight-jh7100-r0", "starfive,jh7100"; + + aliases { + serial0 = &uart3; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + cpus { + timebase-frequency = <6250000>; + }; + + memory@80000000 { + device_type = "memory"; + reg = <0x0 0x80000000 0x2 0x0>; + }; + + leds { + compatible = "gpio-leds"; + + led-ack { + gpios = <&gpio 43 GPIO_ACTIVE_HIGH>; + color = <LED_COLOR_ID_GREEN>; + function = LED_FUNCTION_HEARTBEAT; + linux,default-trigger = "heartbeat"; + label = "ack"; + }; + }; +}; + +&gpio { + i2c0_pins: i2c0-0 { + i2c-pins { + pinmux = <GPIOMUX(62, GPO_LOW, + GPO_I2C0_PAD_SCK_OEN, + GPI_I2C0_PAD_SCK_IN)>, + <GPIOMUX(61, GPO_LOW, + GPO_I2C0_PAD_SDA_OEN, + GPI_I2C0_PAD_SDA_IN)>; + bias-disable; /* external pull-up */ + input-enable; + input-schmitt-enable; + }; + }; + + i2c1_pins: i2c1-0 { + i2c-pins { + pinmux = <GPIOMUX(47, GPO_LOW, + GPO_I2C1_PAD_SCK_OEN, + GPI_I2C1_PAD_SCK_IN)>, + <GPIOMUX(48, GPO_LOW, + GPO_I2C1_PAD_SDA_OEN, + GPI_I2C1_PAD_SDA_IN)>; + bias-pull-up; + input-enable; + input-schmitt-enable; + }; + }; + + i2c2_pins: i2c2-0 { + i2c-pins { + pinmux = <GPIOMUX(60, GPO_LOW, + GPO_I2C2_PAD_SCK_OEN, + GPI_I2C2_PAD_SCK_IN)>, + <GPIOMUX(59, GPO_LOW, + GPO_I2C2_PAD_SDA_OEN, + GPI_I2C2_PAD_SDA_IN)>; + bias-disable; /* external pull-up */ + input-enable; + input-schmitt-enable; + }; + }; + + uart3_pins: uart3-0 { + rx-pins { + pinmux = <GPIOMUX(13, GPO_LOW, GPO_DISABLE, + GPI_UART3_PAD_SIN)>; + bias-pull-up; + drive-strength = <14>; + input-enable; + input-schmitt-enable; + slew-rate = <0>; + }; + tx-pins { + pinmux = <GPIOMUX(14, GPO_UART3_PAD_SOUT, + GPO_ENABLE, GPI_NONE)>; + bias-disable; + drive-strength = <35>; + input-disable; + input-schmitt-disable; + slew-rate = <0>; + }; + }; +}; + +&i2c0 { + clock-frequency = <100000>; + i2c-sda-hold-time-ns = <300>; + i2c-sda-falling-time-ns = <500>; + i2c-scl-falling-time-ns = <500>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + status = "okay"; + + pmic@5e { + compatible = "ti,tps65086"; + reg = <0x5e>; + gpio-controller; + #gpio-cells = <2>; + + regulators { + }; + }; +}; + +&i2c1 { + clock-frequency = <400000>; + i2c-sda-hold-time-ns = <300>; + i2c-sda-falling-time-ns = <100>; + i2c-scl-falling-time-ns = <100>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + status = "okay"; +}; + +&i2c2 { + clock-frequency = <100000>; + i2c-sda-hold-time-ns = <300>; + i2c-sda-falling-time-ns = <500>; + i2c-scl-falling-time-ns = <500>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins>; + status = "okay"; +}; + +&osc_sys { + clock-frequency = <25000000>; +}; + +&osc_aud { + clock-frequency = <27000000>; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins>; + status = "okay"; +}; diff --git a/arch/riscv/boot/dts/starfive/jh7100.dtsi b/arch/riscv/boot/dts/starfive/jh7100.dtsi new file mode 100644 index 000000000000..69f22f9aad9d --- /dev/null +++ b/arch/riscv/boot/dts/starfive/jh7100.dtsi @@ -0,0 +1,230 @@ +// SPDX-License-Identifier: GPL-2.0 OR MIT +/* + * Copyright (C) 2021 StarFive Technology Co., Ltd. + * Copyright (C) 2021 Emil Renner Berthing <kernel@esmil.dk> + */ + +/dts-v1/; +#include <dt-bindings/clock/starfive-jh7100.h> +#include <dt-bindings/reset/starfive-jh7100.h> + +/ { + compatible = "starfive,jh7100"; + #address-cells = <2>; + #size-cells = <2>; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + compatible = "sifive,u74-mc", "riscv"; + reg = <0>; + d-cache-block-size = <64>; + d-cache-sets = <64>; + d-cache-size = <32768>; + d-tlb-sets = <1>; + d-tlb-size = <32>; + device_type = "cpu"; + i-cache-block-size = <64>; + i-cache-sets = <64>; + i-cache-size = <32768>; + i-tlb-sets = <1>; + i-tlb-size = <32>; + mmu-type = "riscv,sv39"; + riscv,isa = "rv64imafdc"; + tlb-split; + + cpu0_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + cpu@1 { + compatible = "sifive,u74-mc", "riscv"; + reg = <1>; + d-cache-block-size = <64>; + d-cache-sets = <64>; + d-cache-size = <32768>; + d-tlb-sets = <1>; + d-tlb-size = <32>; + device_type = "cpu"; + i-cache-block-size = <64>; + i-cache-sets = <64>; + i-cache-size = <32768>; + i-tlb-sets = <1>; + i-tlb-size = <32>; + mmu-type = "riscv,sv39"; + riscv,isa = "rv64imafdc"; + tlb-split; + + cpu1_intc: interrupt-controller { + compatible = "riscv,cpu-intc"; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + }; + + osc_sys: osc_sys { + compatible = "fixed-clock"; + #clock-cells = <0>; + /* This value must be overridden by the board */ + clock-frequency = <0>; + }; + + osc_aud: osc_aud { + compatible = "fixed-clock"; + #clock-cells = <0>; + /* This value must be overridden by the board */ + clock-frequency = <0>; + }; + + gmac_rmii_ref: gmac_rmii_ref { + compatible = "fixed-clock"; + #clock-cells = <0>; + /* Should be overridden by the board when needed */ + clock-frequency = <0>; + }; + + gmac_gr_mii_rxclk: gmac_gr_mii_rxclk { + compatible = "fixed-clock"; + #clock-cells = <0>; + /* Should be overridden by the board when needed */ + clock-frequency = <0>; + }; + + soc { + compatible = "simple-bus"; + interrupt-parent = <&plic>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + clint: clint@2000000 { + compatible = "starfive,jh7100-clint", "sifive,clint0"; + reg = <0x0 0x2000000 0x0 0x10000>; + interrupts-extended = <&cpu0_intc 3 &cpu0_intc 7 + &cpu1_intc 3 &cpu1_intc 7>; + }; + + plic: interrupt-controller@c000000 { + compatible = "starfive,jh7100-plic", "sifive,plic-1.0.0"; + reg = <0x0 0xc000000 0x0 0x4000000>; + interrupts-extended = <&cpu0_intc 11 &cpu0_intc 9 + &cpu1_intc 11 &cpu1_intc 9>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + riscv,ndev = <127>; + }; + + clkgen: clock-controller@11800000 { + compatible = "starfive,jh7100-clkgen"; + reg = <0x0 0x11800000 0x0 0x10000>; + clocks = <&osc_sys>, <&osc_aud>, <&gmac_rmii_ref>, <&gmac_gr_mii_rxclk>; + clock-names = "osc_sys", "osc_aud", "gmac_rmii_ref", "gmac_gr_mii_rxclk"; + #clock-cells = <1>; + }; + + rstgen: reset-controller@11840000 { + compatible = "starfive,jh7100-reset"; + reg = <0x0 0x11840000 0x0 0x10000>; + #reset-cells = <1>; + }; + + i2c0: i2c@118b0000 { + compatible = "snps,designware-i2c"; + reg = <0x0 0x118b0000 0x0 0x10000>; + clocks = <&clkgen JH7100_CLK_I2C0_CORE>, + <&clkgen JH7100_CLK_I2C0_APB>; + clock-names = "ref", "pclk"; + resets = <&rstgen JH7100_RSTN_I2C0_APB>; + interrupts = <96>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c1: i2c@118c0000 { + compatible = "snps,designware-i2c"; + reg = <0x0 0x118c0000 0x0 0x10000>; + clocks = <&clkgen JH7100_CLK_I2C1_CORE>, + <&clkgen JH7100_CLK_I2C1_APB>; + clock-names = "ref", "pclk"; + resets = <&rstgen JH7100_RSTN_I2C1_APB>; + interrupts = <97>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + gpio: pinctrl@11910000 { + compatible = "starfive,jh7100-pinctrl"; + reg = <0x0 0x11910000 0x0 0x10000>, + <0x0 0x11858000 0x0 0x1000>; + reg-names = "gpio", "padctl"; + clocks = <&clkgen JH7100_CLK_GPIO_APB>; + resets = <&rstgen JH7100_RSTN_GPIO_APB>; + interrupts = <32>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + uart2: serial@12430000 { + compatible = "starfive,jh7100-uart", "snps,dw-apb-uart"; + reg = <0x0 0x12430000 0x0 0x10000>; + clocks = <&clkgen JH7100_CLK_UART2_CORE>, + <&clkgen JH7100_CLK_UART2_APB>; + clock-names = "baudclk", "apb_pclk"; + resets = <&rstgen JH7100_RSTN_UART2_APB>; + interrupts = <72>; + reg-io-width = <4>; + reg-shift = <2>; + status = "disabled"; + }; + + uart3: serial@12440000 { + compatible = "starfive,jh7100-uart", "snps,dw-apb-uart"; + reg = <0x0 0x12440000 0x0 0x10000>; + clocks = <&clkgen JH7100_CLK_UART3_CORE>, + <&clkgen JH7100_CLK_UART3_APB>; + clock-names = "baudclk", "apb_pclk"; + resets = <&rstgen JH7100_RSTN_UART3_APB>; + interrupts = <73>; + reg-io-width = <4>; + reg-shift = <2>; + status = "disabled"; + }; + + i2c2: i2c@12450000 { + compatible = "snps,designware-i2c"; + reg = <0x0 0x12450000 0x0 0x10000>; + clocks = <&clkgen JH7100_CLK_I2C2_CORE>, + <&clkgen JH7100_CLK_I2C2_APB>; + clock-names = "ref", "pclk"; + resets = <&rstgen JH7100_RSTN_I2C2_APB>; + interrupts = <74>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c3: i2c@12460000 { + compatible = "snps,designware-i2c"; + reg = <0x0 0x12460000 0x0 0x10000>; + clocks = <&clkgen JH7100_CLK_I2C3_CORE>, + <&clkgen JH7100_CLK_I2C3_APB>; + clock-names = "ref", "pclk"; + resets = <&rstgen JH7100_RSTN_I2C3_APB>; + interrupts = <75>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + }; +}; |