aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* xen/grant: Add helper gnttab_page_grant_foreign_access_ref_oneJulien Grall2015-10-231-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | Many PV drivers contain the idiom: pfn = page_to_gfn(...) /* Or similar */ gnttab_grant_foreign_access_ref Replace it by a new helper. Note that when Linux is using a different page granularity than Xen, the helper only gives access to the first 4KB grant. This is useful where drivers are allocating a full Linux page for each grant. Also include xen/interface/grant_table.h rather than xen/grant_table.h in asm/page.h for x86 to fix a compilation issue [1]. Only the former is useful in order to get the structure definition. [1] Interdependency between asm/page.h and xen/grant_table.h which result to page_mfn not being defined when necessary. Signed-off-by: Julien Grall <julien.grall@citrix.com> Reviewed-by: David Vrabel <david.vrabel@citrix.com> Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com>
* xen/grant: Introduce helpers to split a page into grantJulien Grall2015-10-233-1/+69
| | | | | | | | | | | | | | | | | | | | | | | Currently, a grant is always based on the Xen page granularity (i.e 4KB). When Linux is using a different page granularity, a single page will be split between multiple grants. The new helpers will be in charge of splitting the Linux page into grants and call a function given by the caller on each grant. Also provide an helper to count the number of grants within a given contiguous region. Note that the x86/include/asm/xen/page.h is now including xen/interface/grant_table.h rather than xen/grant_table.h. It's necessary because xen/grant_table.h depends on asm/xen/page.h and will break the compilation. Furthermore, only definition in interface/grant_table.h is required. Signed-off-by: Julien Grall <julien.grall@citrix.com> Reviewed-by: David Vrabel <david.vrabel@citrix.com> Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com>
* xen: Add Xen specific page definitionJulien Grall2015-10-231-1/+26
| | | | | | | | | | | | | | | | | | The Xen hypercall interface is always using 4K page granularity on ARM and x86 architecture. With the incoming support of 64K page granularity for ARM64 guest, it won't be possible to re-use the Linux page definition in Xen drivers. Introduce Xen page definition helpers based on the Linux page definition. They have exactly the same name but prefixed with XEN_/xen_ prefix. Also modify xen_page_to_gfn to use new Xen page definition. Signed-off-by: Julien Grall <julien.grall@citrix.com> Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com>
* arm/xen: Drop pte_mfn and mfn_pteJulien Grall2015-10-231-3/+0
| | | | | | | | | | | They are not used in common code expect in one place in balloon.c which is only compiled when Linux is using PV MMU. It's not the case on ARM. Rather than worrying how to handle the 64KB case, drop them. Signed-off-by: Julien Grall <julien.grall@citrix.com> Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com>
* net/xen-netback: xenvif_gop_frag_copy: move GSO check out of the loopJulien Grall2015-10-231-7/+7
| | | | | | | | | The skb doesn't change within the function. Therefore it's only necessary to check if we need GSO once at the beginning. Signed-off-by: Julien Grall <julien.grall@citrix.com> Acked-by: Wei Liu <wei.liu2@citrix.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com>
* xen/balloon: pre-allocate p2m entries for ballooned pagesDavid Vrabel2015-10-231-0/+5
| | | | | | | | | | | | | | | Pages returned by alloc_xenballooned_pages() will be used for grant mapping which will call set_phys_to_machine() (in PV guests). Ballooned pages are set as INVALID_P2M_ENTRY in the p2m and thus may be using the (shared) missing tables and a subsequent set_phys_to_machine() will need to allocate new tables. Since the grant mapping may be done from a context that cannot sleep, the p2m entries must already be allocated. Signed-off-by: David Vrabel <david.vrabel@citrix.com> Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
* x86/xen: export xen_alloc_p2m_entry()David Vrabel2015-10-232-6/+15
| | | | | | | | | | | | | | Rename alloc_p2m() to xen_alloc_p2m_entry() and export it. This is useful for ensuring that a p2m entry is allocated (i.e., not a shared missing or identity entry) so that subsequent set_phys_to_machine() calls will require no further allocations. Signed-off-by: David Vrabel <david.vrabel@citrix.com> Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com> --- v3: - Make xen_alloc_p2m_entry() a nop on auto-xlate guests.
* xen/balloon: use hotplugged pages for foreign mappings etc.David Vrabel2015-10-232-10/+81
| | | | | | | | | | | | | | | | | | | | alloc_xenballooned_pages() is used to get ballooned pages to back foreign mappings etc. Instead of having to balloon out real pages, use (if supported) hotplugged memory. This makes more memory available to the guest and reduces fragmentation in the p2m. This is only enabled if the xen.balloon.hotplug_unpopulated sysctl is set to 1. This sysctl defaults to 0 in case the udev rules to automatically online hotplugged memory do not exist. Signed-off-by: David Vrabel <david.vrabel@citrix.com> Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com> --- v3: - Add xen.balloon.hotplug_unpopulated sysctl to enable use of hotplug for unpopulated pages.
* xen/balloon: make alloc_xenballoon_pages() always allocate low pagesDavid Vrabel2015-10-236-20/+13
| | | | | | | | All users of alloc_xenballoon_pages() wanted low memory pages, so remove the option for high memory. Signed-off-by: David Vrabel <david.vrabel@citrix.com> Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
* xen/balloon: only hotplug additional memory if requiredDavid Vrabel2015-10-231-4/+19
| | | | | | | | | | | | | | | | | | | Now that we track the total number of pages (included hotplugged regions), it is easy to determine if more memory needs to be hotplugged. Add a new BP_WAIT state to signal that the balloon process needs to wait until kicked by the memory add notifier (when the new section is onlined by userspace). Signed-off-by: David Vrabel <david.vrabel@citrix.com> Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com> --- v3: - Return BP_WAIT if enough sections are already hotplugged. v2: - New BP_WAIT status after adding new memory sections.
* xen/balloon: rationalize memory hotplug statsDavid Vrabel2015-10-232-67/+13
| | | | | | | | | | | | | | The stats used for memory hotplug make no sense and are fiddled with in odd ways. Remove them and introduce total_pages to track the total number of pages (both populated and unpopulated) including those within hotplugged regions (note that this includes not yet onlined pages). This will be used in a subsequent commit (xen/balloon: only hotplug additional memory if required) when deciding whether additional memory needs to be hotplugged. Signed-off-by: David Vrabel <david.vrabel@citrix.com> Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
* xen/balloon: find non-conflicting regions to place hotplugged memoryDavid Vrabel2015-10-231-20/+53
| | | | | | | | | | | | Instead of placing hotplugged memory at the end of RAM (which may conflict with PCI devices or reserved regions) use allocate_resource() to get a new, suitably aligned resource that does not conflict. Signed-off-by: David Vrabel <david.vrabel@citrix.com> Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com> --- v3: - Remove stale comment.
* x86/xen: discard RAM regions above the maximum reservationDavid Vrabel2015-10-231-2/+5
| | | | | | | | | During setup, discard RAM regions that are above the maximum reservation (instead of marking them as E820_UNUSABLE). This allows hotplug memory to be placed at these addresses. Signed-off-by: David Vrabel <david.vrabel@citrix.com> Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
* xen/balloon: remove scratch page left oversDavid Vrabel2015-10-231-3/+0
| | | | | | | | | | | Commit 0bb599fd30108883b00c7d4a226eeb49111e6932 (xen: remove scratch frames for ballooned pages and m2p override) removed the use of the scratch page for ballooned out pages. Remove some left over function definitions. Signed-off-by: David Vrabel <david.vrabel@citrix.com> Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com>
* mm: memory hotplug with an existing resourceDavid Vrabel2015-10-232-8/+23
| | | | | | | | | | | | | Add add_memory_resource() to add memory using an existing "System RAM" resource. This is useful if the memory region is being located by finding a free resource slot with allocate_resource(). Xen guests will make use of this in their balloon driver to hotplug arbitrary amounts of memory in response to toolstack requests. Signed-off-by: David Vrabel <david.vrabel@citrix.com> Reviewed-by: Daniel Kiper <daniel.kiper@oracle.com> Reviewed-by: Tang Chen <tangchen@cn.fujitsu.com>
* Linux 4.3-rc6v4.3-rc6Linus Torvalds2015-10-181-1/+1
|
* Merge branch 'i2c/for-current' of ↵Linus Torvalds2015-10-185-18/+51
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux Pull i2c fixes from Wolfram Sang: "Here are some bugfixes for the I2C subsystem. Kieran found a flaw in the recently renewed wake irq handling. Mika handled a user bug report where the ACPI info turned out to be unusable. I updated MAINTAINERS so that such bug reports will sooner get to the right people. Geert pointed me to a problem of some i2c drivers regarding PM which I fixed" * 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: i2c: designware: Do not use parameters from ACPI on Dell Inspiron 7348 MAINTAINERS: add maintainers for Synopsis Designware I2C drivers i2c: designware-platdrv: enable RuntimePM before registering to the core i2c: s3c2410: enable RuntimePM before registering to the core i2c: rcar: enable RuntimePM before registering to the core i2c: return probe deferred status on dev_pm_domain_attach
| * i2c: designware: Do not use parameters from ACPI on Dell Inspiron 7348Mika Westerberg2015-10-181-0/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ACPI SSCN/FMCN methods were originally added because then the platform can provide the most accurate HCNT/LCNT values to the driver. However, this seems not to be true for Dell Inspiron 7348 where using these causes the touchpad to fail in boot: i2c_hid i2c-DLL0675:00: failed to retrieve report from device. i2c_designware INT3433:00: i2c_dw_handle_tx_abort: lost arbitration i2c_hid i2c-DLL0675:00: failed to retrieve report from device. i2c_designware INT3433:00: controller timed out The values received from ACPI are (in fast mode): HCNT: 72 LCNT: 160 this translates to following timings (input clock is 100MHz on Broadwell): tHIGH: 720 ns (spec min 600 ns) tLOW: 1600 ns (spec min 1300 ns) Bus period: 2920 ns (assuming 300 ns tf and tr) Bus speed: 342.5 kHz Both tHIGH and tLOW are within the I2C specification. The calculated values when ACPI parameters are not used are (in fast mode): HCNT: 87 LCNT: 159 which translates to: tHIGH: 870 ns (spec min 600 ns) tLOW: 1590 ns (spec min 1300 ns) Bus period 3060 ns (assuming 300 ns tf and tr) Bus speed 326.8 kHz These values are also within the I2C specification. Since both ACPI and calculated values meet the I2C specification timing requirements it is hard to say why the touchpad does not function properly with the ACPI values except that the bus speed is higher in this case (but still well below the max 400kHz). Solve this by adding DMI quirk to the driver that disables using ACPI parameters on this particulare machine. Reported-by: Pavel Roskin <plroskin@gmail.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Tested-by: Pavel Roskin <plroskin@gmail.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org
| * MAINTAINERS: add maintainers for Synopsis Designware I2C driversWolfram Sang2015-10-151-0/+9
| | | | | | | | | | | | | | | | | | | | Those guys already have been helpful in the past and are actively working on this driver, unlike me. Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
| * i2c: designware-platdrv: enable RuntimePM before registering to the coreWolfram Sang2015-10-151-6/+7
| | | | | | | | | | | | | | | | | | | | | | The core may register clients attached to this master which may use funtionality from the master. So, RuntimePM must be enabled before, otherwise this will fail. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: stable@kernel.org
| * i2c: s3c2410: enable RuntimePM before registering to the coreWolfram Sang2015-10-151-3/+5
| | | | | | | | | | | | | | | | | | | | | | | | The core may register clients attached to this master which may use funtionality from the master. So, RuntimePM must be enabled before, otherwise this will fail. While here, move drvdata, too. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Acked-by: Kukjin Kim <kgene@kernel.org> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org
| * i2c: rcar: enable RuntimePM before registering to the coreWolfram Sang2015-10-151-3/+4
| | | | | | | | | | | | | | | | | | | | | | The core may register clients attached to this master which may use funtionality from the master. So, RuntimePM must be enabled before, otherwise this will fail. While here, move drvdata, too. Reported-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org
| * i2c: return probe deferred status on dev_pm_domain_attachKieran Bingham2015-10-151-6/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | A change of return status was introduced in commit 3fffd1283927 ("i2c: allow specifying separate wakeup interrupt in device tree") The commit prevents the defer status being passed up the call stack appropriately when dev_pm_domain_attach returns -EPROBE_DEFER. Catch the PROBE_DEFER and clear up the IRQ wakeup status Signed-off-by: Kieran Bingham <kieranbingham@gmail.com> Fixes: 3fffd1283927 ("i2c: allow specifying separate wakeup interrupt in device tree") Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
| |
| \
*-. \ Merge branches 'irq-urgent-for-linus' and 'timers-urgent-for-linus' of ↵Linus Torvalds2015-10-173-6/+6
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull irq/timer fixes from Thomas Gleixner: "irq: a fix for the new hierarchical MSI interrupt handling which unbreaks PCI=n configurations. timers: a fix for the new hrtimer clock offset update mechanism to ensure that the boot time offset is respected" * 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: genirq/msi: Do not use pci_msi_[un]mask_irq as default methods * 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: timekeeping: Increment clock_was_set_seq in timekeeping_init()
| | * | timekeeping: Increment clock_was_set_seq in timekeeping_init()Thomas Gleixner2015-10-161-1/+1
| | |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | timekeeping_init() can set the wall time offset, so we need to increment the clock_was_set_seq counter. That way hrtimers will pick up the early offset immediately. Otherwise on a machine which does not set wall time later in the boot process the hrtimer offset is stale at 0 and wall time timers are going to expire with a delay of 45 years. Fixes: 868a3e915f7f "hrtimer: Make offset update smarter" Reported-and-tested-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Stefan Liebler <stli@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: John Stultz <john.stultz@linaro.org>
| * / genirq/msi: Do not use pci_msi_[un]mask_irq as default methodsMarc Zyngier2015-10-162-5/+5
| |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When we create a generic MSI domain, that MSI_FLAG_USE_DEF_CHIP_OPS is set, and that any of .mask or .unmask are NULL in the irq_chip structure, we set them to pci_msi_[un]mask_irq. This is a bad idea for at least two reasons: - PCI_MSI might not be selected, kernel fails to build (yes, this is legitimate, at least on arm64!) - This may not be a PCI/MSI domain at all (platform MSI, for example) Either way, this looks wrong. Move the overriding of mask/unmask to the PCI counterpart, and panic is any of these two methods is not set in the core code (they really should be present). Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Cc: Jiang Liu <jiang.liu@linux.intel.com> Cc: Bjorn Helgaas <bhelgaas@google.com> Link: http://lkml.kernel.org/r/1444760085-27857-1-git-send-email-marc.zyngier@arm.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* | Merge branch 'for-linus' of ↵Linus Torvalds2015-10-162-9/+9
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input Pull input fixes from Dmitry Torokhov: "Just two small fixups to ads7846 touchscreen controller driver and Cypress touchpad driver" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: cyapa - fix the copy paste error on electrodes_rx value Input: ads7846 - correct the value got from SPI
| * | Input: cyapa - fix the copy paste error on electrodes_rx valueDudley Du2015-10-131-7/+3
| | | | | | | | | | | | | | | | | | | | | | | | Fix the copy paste error on the electrodes_rx value set code which will cause the electrodes_rx value be always set to the value of electrodes_y. Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Dudley Du <dudl@cypress.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
| * | Input: ads7846 - correct the value got from SPIAndrey Gelman2015-10-061-2/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | According to the touch controller spec, SPI return a 16 bit value, only 12 bits are valid, they are bit[14-3]. The value of MISO and MOSI can be configured when SPI is in idle mode. Currently this touch driver assumes the SPI bus sets the MOSI and MISO in low level when SPI bus is in idle mode. So the bit[15] of the value got from SPI bus is always 0. But when SPI bus congfigures the MOSI and MISO in high level during the SPI idle mode, the bit[15] of the value get from SPI is always 1. If bit[15] is not masked, we may get the wrong value. Mask the invalid bit to make sure the correct value gets returned. Regardless of the SPI bus idle configuration. Signed-off-by: Andrey Gelman <andrey.gelman@compulab.co.il> Signed-off-by: Haibo Chen <haibo.chen@freescale.com> Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* | | Merge tag 'clk-fixes-for-linus' of ↵Linus Torvalds2015-10-161-1/+3
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux Pull clk fix from Stephen Boyd: "Just one revert for Armada XP devices: the conversion to of_clk_get_parent_name() wasn't a direct translation, so we revert back to of_clk_get() + __clk_get_name(). We could make of_clk_get_parent_name() more robust, but that may have unintended side-effects, so we'll do that in the next version" * tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: Partially revert "clk: mvebu: Convert to clk_hw based provider APIs"
| * | | Partially revert "clk: mvebu: Convert to clk_hw based provider APIs"Stephen Boyd2015-10-141-1/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This partially reverts commit eca61c9ff2588e1df373e61078e1874976315839. Thomas reports that it causes regressions on Armada XP devices. This is because of_clk_get_parent_name() relies on the property 'clock-output-names' to resolve the name of a clock's parent, without trying to get the clock from the framework and call __clk_get_name(). Given that Armada XP devices don't have the 'clock-output-names' property, of_clk_get_parent_name() returns the name of the node which doesn't match the actual parent clock's name at all, causing CPU clocks to never link up with their parents. Reported-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
* | | | Merge tag 'dm-4.3-fixes-3' of ↵Linus Torvalds2015-10-162-4/+13
|\ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm Pull device mapper fixes from Mike Snitzer: "Two DM target error path cleanup fixes (one for stable in DM thinp and one for a v4.3-rc5 thinko in DM snapshot)" * tag 'dm-4.3-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: dm thin: fix missing pool reference count decrement in pool_ctr error path dm snapshot persistent: fix missing cleanup in persistent_ctr error path
| * | | | dm thin: fix missing pool reference count decrement in pool_ctr error pathMike Snitzer2015-10-131-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fixes: ac8c3f3df ("dm thin: generate event when metadata threshold passed") Signed-off-by: Mike Snitzer <snitzer@redhat.com> Cc: stable@vger.kernel.org # 3.10+
| * | | | dm snapshot persistent: fix missing cleanup in persistent_ctr error pathSudip Mukherjee2015-10-131-3/+12
| | |_|/ | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If an unsupported option is given then the early return from persistent_ctr() leaked memory allocated for the 'pstore' and never destroyed the 'metadata_wq'. Fixes: b0d3cc011e53 ("dm snapshot: add new persistent store option to support overflow") Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
* | | | Merge branch 'for-linus-4.3' of ↵Linus Torvalds2015-10-163-5/+16
|\ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs Pull btrfs fixes from Chris Mason: "I have two more bug fixes for btrfs. My commit fixes a bug we hit last week at FB, a combination of lots of hard links and an admin command to resolve inode numbers. Dave is adding checks to make sure balance on current kernels ignores filters it doesn't understand. The penalty for being wrong is just doing more work (not crashing etc), but it's a good fix" * 'for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: btrfs: fix use after free iterating extrefs btrfs: check unsupported filters in balance arguments
| * | | | btrfs: fix use after free iterating extrefsChris Mason2015-10-131-5/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The code for btrfs inode-resolve has never worked properly for files with enough hard links to trigger extrefs. It was trying to get the leaf out of a path after freeing the path: btrfs_release_path(path); leaf = path->nodes[0]; item_size = btrfs_item_size_nr(leaf, slot); The fix here is to use the extent buffer we cloned just a little higher up to avoid deadlocks caused by using the leaf in the path. Signed-off-by: Chris Mason <clm@fb.com> cc: stable@vger.kernel.org # v3.7+ cc: Mark Fasheh <mfasheh@suse.de> Reviewed-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: Mark Fasheh <mfasheh@suse.de>
| * | | | btrfs: check unsupported filters in balance argumentsDavid Sterba2015-10-132-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We don't verify that all the balance filter arguments supplemented by the flags are actually known to the kernel. Thus we let it silently pass and do nothing. At the moment this means only the 'limit' filter, but we're going to add a few more soon so it's better to have that fixed. Also in older stable kernels so that it works with newer userspace tools. Cc: stable@vger.kernel.org # 3.16+ Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Chris Mason <clm@fb.com>
* | | | | Merge branch 'for-linus' of ↵Linus Torvalds2015-10-162-6/+17
|\ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client Pull Ceph fixes from Sage Weil: "Just two small items from Ilya: The first patch fixes the RBD readahead to grab full objects. The second fixes the write ops to prevent undue promotion when a cache tier is configured on the server side" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: rbd: use writefull op for object size writes rbd: set max_sectors explicitly
| * | | | | rbd: use writefull op for object size writesIlya Dryomov2015-10-162-6/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This covers only the simplest case - an object size sized write, but it's still useful in tiering setups when EC is used for the base tier as writefull op can be proxied, saving an object promotion. Even though updating ceph_osdc_new_request() to allow writefull should just be a matter of fixing an assert, I didn't do it because its only user is cephfs. All other sites were updated. Reflects ceph.git commit 7bfb7f9025a8ee0d2305f49bf0336d2424da5b5b. Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Reviewed-by: Alex Elder <elder@linaro.org>
| * | | | | rbd: set max_sectors explicitlyIlya Dryomov2015-10-161-0/+1
| | |/ / / | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 30e2bc08b2bb ("Revert "block: remove artifical max_hw_sectors cap"") restored a clamp on max_sectors. It's now 2560 sectors instead of 1024, but it's not good enough: we set max_hw_sectors to rbd object size because we don't want object sized I/Os to be split, and the default object size is 4M. So, set max_sectors to max_hw_sectors in rbd at queue init time. Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Reviewed-by: Alex Elder <elder@linaro.org>
* | | | | Merge tag 'pm+acpi-4.3-rc6' of ↵Linus Torvalds2015-10-167-49/+21
|\ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull power management and ACPI fixes from Rafael Wysocki: "These fix two recent regressions (ACPICA, the generic power domains framework) and one crash that may happen on specific hardware supported since 4.1 (intel_pstate). Specifics: - Fix a regression introduced by a recent ACPICA cleanup that uncovered a latent bug (Lv Zheng). - Fix a recent regression in the generic power domains framework that may cause it to violate PM QoS latency constraints in some cases (Ulf Hansson). - Fix an intel_pstate driver crash on the Knights Landing chips that do not update the MPERF counter as often as expected by the driver which may result in a divide by 0 (Srinivas Pandruvada)" * tag 'pm+acpi-4.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: cpufreq: intel_pstate: Fix divide by zero on Knights Landing (KNL) ACPICA: Tables: Fix FADT dependency regression PM / Domains: Fix validation of latency constraints in genpd governor
| | \ \ \ \
| | \ \ \ \
| | \ \ \ \
| | \ \ \ \
| *---. \ \ \ \ Merge branches 'acpica', 'pm-domains' and 'pm-cpufreq'Rafael J. Wysocki2015-10-167-49/+21
| |\ \ \ \ \ \ \ | | |_|_|/ / / / | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * acpica: ACPICA: Tables: Fix FADT dependency regression * pm-domains: PM / Domains: Fix validation of latency constraints in genpd governor * pm-cpufreq: cpufreq: intel_pstate: Fix divide by zero on Knights Landing (KNL)
| | | | * | | | cpufreq: intel_pstate: Fix divide by zero on Knights Landing (KNL)Srinivas Pandruvada2015-10-151-0/+5
| | |_|/ / / / | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This is a workaround for KNL platform, where in some cases MPERF counter will not have updated value before next read of MSR_IA32_MPERF. In this case divide by zero will occur. This change ignores current sample for busy calculation in this case. Fixes: b34ef932d79a (intel_pstate: Knights Landing support) Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com> Cc: 4.1+ <stable@vger.kernel.org> # 4.1+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
| | | * | | | PM / Domains: Fix validation of latency constraints in genpd governorUlf Hansson2015-10-141-16/+6
| | |/ / / / | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit ba2bbfbf6307 (PM / Domains: Remove intermediate states from the power off sequence) changed the power off sequence in genpd. That also required some updates regarding the validation of latency constraints in the genpd governor. Unfortunate that wasn't covered, so let's fix this. From a runtime PM and latency point of view, we need to consider the worst case scenario while validating latency constraints. That's typically when a call to pm_runtime_get_sync() needs to wait for a ongoing runtime suspend operation to be carried out, as it then also needs to wait for the device to be runtime resumed again. The above mentioned commit made the genpd governor's ->stop_ok() callback responsible of validating genpd's device's runtime suspend/resume latency. In other words, the constraint needs to be validated towards the relevant latencies present in genpd's ->runtime_suspend|resume() callbacks. Earlier, that included latencies from the ->stop|start() callbacks, but as ->save|restore_state() are now also being invoked from genpd's ->runtime_suspend|resume() and to comply with the worst case scenario, let's take also those latencies into account. Fixes: ba2bbfbf6307 (PM / Domains: Remove intermediate states from the power off sequence) Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
| | * | | | ACPICA: Tables: Fix FADT dependency regressionLv Zheng2015-10-145-33/+10
| |/ / / / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some logics actually relying on the existence of FADT, currently relies on the number of loaded tables. This false dependency can easily trigger regressions. One of them has been introduced by commit 8ec3f459073e (ACPICA: Tables: Fix global table list issues by removing fixed table). The commit changing the fixed table indexes results in the change of FADT table index, originally, it was 3 (thus the installed table count should be greater than 4), while currently it is 0 (and the installed table count may be 3). This patch fixes this regression by cleaning up the code. Lv Zheng. Link: https://bugzilla.kernel.org/show_bug.cgi?id=105351 Fixes: 8ec3f459073e (ACPICA: Tables: Fix global table list issues by removing fixed table) Reported-and-tested-by: Meelis Roos <mroos@linux.ee> Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* | | | | Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linuxLinus Torvalds2015-10-1612-16/+115
|\ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull drm fixes from Dave Airlie: "Nothing too crazy or exciting: - two MAINTAINERS entries that I didn't see the point in delaying. - one drm mst fix to stop sending uninitialised data to monitors - two amdgpu fixes - one radeon mst tiling fix - one vmwgfx regression fix - one virtio warning fix. I have found one locking problem that needs a bit of reorg to fix, but I'm not sure it's worth putting in -fixes as I don't think we've seen it hit in the real world ever, I just found it using the virtio-gpu driver when working on it. I'll possibly send it next week once I've time to discuss with Daniel" * 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: drm/virtio: use %llu format string form atomic64_t MAINTAINERS: Add myself as maintainer for the gma500 driver MAINTAINERS: add a maintainer for the atmel-hlcdc DRM driver drm/amdgpu: Keep the pflip interrupts always enabled v7 drm/amdgpu: adjust default dispclk (v2) drm/dp/mst: make mst i2c transfer code more robust. drm/radeon: attach tile property to mst connector drm/vmwgfx: Fix kernel NULL pointer dereference on older hardware
| * | | | | drm/virtio: use %llu format string form atomic64_tArnd Bergmann2015-10-162-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The virtgpu driver prints the last_seq variable using the %ld or %lu format string, which does not work correctly on all architectures and causes this compiler warning on ARM: drivers/gpu/drm/virtio/virtgpu_fence.c: In function 'virtio_timeline_value_str': drivers/gpu/drm/virtio/virtgpu_fence.c:64:22: warning: format '%lu' expects argument of type 'long unsigned int', but argument 4 has type 'long long int' [-Wformat=] snprintf(str, size, "%lu", atomic64_read(&fence->drv->last_seq)); ^ drivers/gpu/drm/virtio/virtgpu_debugfs.c: In function 'virtio_gpu_debugfs_irq_info': drivers/gpu/drm/virtio/virtgpu_debugfs.c:37:16: warning: format '%ld' expects argument of type 'long int', but argument 3 has type 'long long int' [-Wformat=] seq_printf(m, "fence %ld %lld\n", ^ In order to avoid the warnings, this changes the format strings to %llu and adds a cast to u64, which makes it work the same way everywhere. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Dave Airlie <airlied@redhat.com>
| * | | | | MAINTAINERS: Add myself as maintainer for the gma500 driverPatrik Jakobsson2015-10-161-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
| * | | | | MAINTAINERS: add a maintainer for the atmel-hlcdc DRM driverBoris BREZILLON2015-10-161-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add myself as the maintainer of the atmel-hlcdc DRM driver. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
| * | | | | Merge branch 'drm-fixes-4.3' of git://people.freedesktop.org/~agd5f/linux ↵Dave Airlie2015-10-165-10/+90
| |\ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | into drm-fixes Just two fixes for amdgpu: - fix pageflip interrupt issue - fix display clock handling on certain fiji boards * 'drm-fixes-4.3' of git://people.freedesktop.org/~agd5f/linux: drm/amdgpu: Keep the pflip interrupts always enabled v7 drm/amdgpu: adjust default dispclk (v2)
generated by cgit (git 2.34.1) at 2025-02-28 11:43:20 +0000