| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| | |
|
| |\
| |
| |
| |
| |
| |
| |
| | |
Pull cramfs fix from Al Viro:
"Regression fix, fallen through the cracks"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
cramfs: fix usage on non-MTD device
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
When both CONFIG_CRAMFS_MTD and CONFIG_CRAMFS_BLOCKDEV are enabled, if
we fail to mount on MTD, we don't try on block device.
Note: this relies upon cramfs_mtd_fill_super() leaving no side
effects on fc state in case of failure; in general, failing
get_tree_...() does *not* mean "fine to try again"; e.g. parsed
options might've been consumed by fill_super callback and freed
on failure.
Fixes: 74f78fc5ef43 ("vfs: Convert cramfs to use the new mount API")
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
| |\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Pull last minute virtio bugfixes from Michael Tsirkin:
"Minor bugfixes all over the place"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_balloon: fix shrinker count
virtio_balloon: fix shrinker scan number of pages
virtio_console: allocate inbufs in add_port() only if it is needed
virtio_ring: fix return code on DMA mapping fails
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Instead of multiplying by page order, virtio balloon divided by page
order. The result is that it can return 0 if there are a bit less
than MAX_ORDER - 1 pages in use, and then shrinker scan won't be called.
Cc: stable@vger.kernel.org
Fixes: 71994620bb25 ("virtio_balloon: replace oom notifier with shrinker")
Signed-off-by: Wei Wang <wei.w.wang@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
virtio_balloon_shrinker_scan should return number of system pages freed,
but because it's calling functions that deal with balloon pages, it gets
confused and sometimes returns the number of balloon pages.
It does not matter practically as the exact number isn't
used, but it seems better to be consistent in case someone
starts using this API.
Further, if we ever tried to iteratively leak pages as
virtio_balloon_shrinker_scan tries to do, we'd run into issues - this is
because freed_pages was accumulating total freed pages, but was also
subtracted on each iteration from pages_to_free, which can result in
either leaking less memory than we were supposed to free, or more if
pages_to_free underruns.
On a system with 4K pages we are lucky that we are never asked to leak
more than 128 pages while we can leak up to 256 at a time,
but it looks like a real issue for systems with page size != 4K.
Fixes: 71994620bb25 ("virtio_balloon: replace oom notifier with shrinker")
Reported-by: Khazhismel Kumykov <khazhy@google.com>
Reviewed-by: Wei Wang <wei.w.wang@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
When we hot unplug a virtserialport and then try to hot plug again,
it fails:
(qemu) chardev-add socket,id=serial0,path=/tmp/serial0,server,nowait
(qemu) device_add virtserialport,bus=virtio-serial0.0,nr=2,\
chardev=serial0,id=serial0,name=serial0
(qemu) device_del serial0
(qemu) device_add virtserialport,bus=virtio-serial0.0,nr=2,\
chardev=serial0,id=serial0,name=serial0
kernel error:
virtio-ports vport2p2: Error allocating inbufs
qemu error:
virtio-serial-bus: Guest failure in adding port 2 for device \
virtio-serial0.0
This happens because buffers for the in_vq are allocated when the port is
added but are not released when the port is unplugged.
They are only released when virtconsole is removed (see a7a69ec0d8e4)
To avoid the problem and to be symmetric, we could allocate all the buffers
in init_vqs() as they are released in remove_vqs(), but it sounds like
a waste of memory.
Rather than that, this patch changes add_port() logic to ignore ENOSPC
error in fill_queue(), which means queue has already been filled.
Fixes: a7a69ec0d8e4 ("virtio_console: free buffers after reset")
Cc: mst@redhat.com
Cc: stable@vger.kernel.org
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Commit 780bc7903a32 ("virtio_ring: Support DMA APIs") makes
virtqueue_add() return -EIO when we fail to map our I/O buffers. This is
a very realistic scenario for guests with encrypted memory, as swiotlb
may run out of space, depending on it's size and the I/O load.
The virtio-blk driver interprets -EIO form virtqueue_add() as an IO
error, despite the fact that swiotlb full is in absence of bugs a
recoverable condition.
Let us change the return code to -ENOMEM, and make the block layer
recover form these failures when virtio-blk encounters the condition
described above.
Cc: stable@vger.kernel.org
Fixes: 780bc7903a32 ("virtio_ring: Support DMA APIs")
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Tested-by: Michael Mueller <mimu@linux.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
| |\ \ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fix from Dmitry Torokhov:
"Just a single revert as RMI mode should not have been enabled for this
model [yet?]"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: synaptics - enable RMI mode for X1 Extreme 2nd Generation"
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
This reverts commit 68b9c5066e39af41d3448abfc887c77ce22dd64d.
Ugh, I really dropped the ball on this one :\. So as it turns out RMI4
works perfectly fine on the X1 Extreme Gen 2 except for one thing I
didn't notice because I usually use the trackpoint: clicking with the
touchpad. Somehow this is broken, in fact we don't even seem to indicate
BTN_LEFT as a valid event type for the RMI4 touchpad. And, I don't even
see any RMI4 events coming from the touchpad when I press down on it.
This only seems to work for PS/2 mode.
Since that means we have a regression, and PS/2 mode seems to work fine
for the time being - revert this for now. We'll have to do a more
thorough investigation on this.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://lore.kernel.org/r/20191119234534.10725-1-lyude@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
| |\ \ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Pull networking fixes from David Miller:
1) Validate tunnel options length in act_tunnel_key, from Xin Long.
2) Fix DMA sync bug in gve driver, from Adi Suresh.
3) TSO kills performance on some r8169 chips due to HW issues, disable
by default in that case, from Corinna Vinschen.
4) Fix clock disable mismatch in fec driver, from Chubong Yuan.
5) Fix interrupt status bits define in hns3 driver, from Huazhong Tan.
6) Fix workqueue deadlocks in qeth driver, from Julian Wiedmann.
7) Don't napi_disable() twice in r8152 driver, from Hayes Wang.
8) Fix SKB extension memory leak, from Florian Westphal.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (54 commits)
r8152: avoid to call napi_disable twice
MAINTAINERS: Add myself as maintainer of virtio-vsock
udp: drop skb extensions before marking skb stateless
net: rtnetlink: prevent underflows in do_setvfinfo()
can: m_can_platform: remove unnecessary m_can_class_resume() call
can: m_can_platform: set net_device structure as driver data
hv_netvsc: Fix send_table offset in case of a host bug
hv_netvsc: Fix offset usage in netvsc_send_table()
net-ipv6: IPV6_TRANSPARENT - check NET_RAW prior to NET_ADMIN
sfc: Only cancel the PPS workqueue if it exists
nfc: port100: handle command failure cleanly
net-sysfs: fix netdev_queue_add_kobject() breakage
r8152: Re-order napi_disable in rtl8152_close
net: qca_spi: Move reset_count to struct qcaspi
net: qca_spi: fix receive buffer size check
net/ibmvnic: Ignore H_FUNCTION return from H_EOI to tolerate XIVE mode
Revert "net/ibmvnic: Fix EOI when running in XIVE mode"
net/mlxfw: Verify FSM error code translation doesn't exceed array size
net/mlx5: Update the list of the PCI supported devices
net/mlx5: Fix auto group size calculation
...
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
Call napi_disable() twice would cause dead lock. There are three situations
may result in the issue.
1. rtl8152_pre_reset() and set_carrier() are run at the same time.
2. Call rtl8152_set_tunable() after rtl8152_close().
3. Call rtl8152_set_ringparam() after rtl8152_close().
For #1, use the same solution as commit 84811412464d ("r8152: Re-order
napi_disable in rtl8152_close"). For #2 and #3, add checking the flag
of IFF_UP and using napi_disable/napi_enable during mutex.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |\ \ \ \
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2019-11-22
this is a pull request of 2 patches for net/master, if possible for the
current release cycle. Otherwise these patches should hit v5.4 via the
stable tree.
Both patches of this pull request target the m_can driver. Pankaj Sharma
fixes the fallout in the m_can_platform part, which appeared with the
introduction of the m_can platform framework.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
The function m_can_runtime_resume() is getting recursively called from
m_can_class_resume(). This results in a lock up.
We need not call m_can_class_resume() during m_can_runtime_resume().
Fixes: f524f829b75a ("can: m_can: Create a m_can platform framework")
Signed-off-by: Pankaj Sharma <pankj.sharma@samsung.com>
Signed-off-by: Sriram Dash <sriram.dash@samsung.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
The current code is failing during clock prepare enable because of not
getting proper clock from platform device.
[ 0.852089] Call trace:
[ 0.854516] 0xffff0000fa22a668
[ 0.857638] clk_prepare+0x20/0x34
[ 0.861019] m_can_runtime_resume+0x2c/0xe4
[ 0.865180] pm_generic_runtime_resume+0x28/0x38
[ 0.869770] __rpm_callback+0x16c/0x1bc
[ 0.873583] rpm_callback+0x24/0x78
[ 0.877050] rpm_resume+0x428/0x560
[ 0.880517] __pm_runtime_resume+0x7c/0xa8
[ 0.884593] m_can_clk_start.isra.9.part.10+0x1c/0xa8
[ 0.889618] m_can_class_register+0x138/0x370
[ 0.893950] m_can_plat_probe+0x120/0x170
[ 0.897939] platform_drv_probe+0x4c/0xa0
[ 0.901924] really_probe+0xd8/0x31c
[ 0.905477] driver_probe_device+0x58/0xe8
[ 0.909551] device_driver_attach+0x68/0x70
[ 0.913711] __driver_attach+0x9c/0xf8
[ 0.917437] bus_for_each_dev+0x50/0xa0
[ 0.921251] driver_attach+0x20/0x28
[ 0.924804] bus_add_driver+0x148/0x1fc
[ 0.928617] driver_register+0x6c/0x124
[ 0.932431] __platform_driver_register+0x48/0x50
[ 0.937113] m_can_plat_driver_init+0x18/0x20
[ 0.941446] do_one_initcall+0x4c/0x19c
[ 0.945259] kernel_init_freeable+0x1d0/0x280
[ 0.949591] kernel_init+0x10/0x100
[ 0.953057] ret_from_fork+0x10/0x18
[ 0.956614] Code: 00000000 00000000 00000000 00000000 (fa22a668)
[ 0.962681] ---[ end trace 881f71bd609de763 ]---
[ 0.967301] Kernel panic - not syncing: Attempted to kill init!
A device driver for CAN controller hardware registers itself with the
Linux network layer as a network device. So, the driver data for m_can
should ideally be of type net_device.
Fixes: f524f829b75a ("can: m_can: Create a m_can platform framework")
Signed-off-by: Pankaj Sharma <pankj.sharma@samsung.com>
Signed-off-by: Sriram Dash <sriram.dash@samsung.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Since I'm actively working on vsock and virtio/vhost transports,
Stefan suggested to help him to maintain it.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Once udp stack has set the UDP_SKB_IS_STATELESS flag, later skb free
assumes all skb head state has been dropped already.
This will leak the extension memory in case the skb has extensions other
than the ipsec secpath, e.g. bridge nf data.
To fix this, set the UDP_SKB_IS_STATELESS flag only if we don't have
extensions or if the extension space can be free'd.
Fixes: 895b5c9f206eb7d25dc1360a ("netfilter: drop bridge nf reset from nf_reset")
Cc: Paolo Abeni <pabeni@redhat.com>
Reported-by: Byron Stanoszek <gandalf@winds.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |/ / / /
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
The "ivm->vf" variable is a u32, but the problem is that a number of
drivers cast it to an int and then forget to check for negatives. An
example of this is in the cxgb4 driver.
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c
2890 static int cxgb4_mgmt_get_vf_config(struct net_device *dev,
2891 int vf, struct ifla_vf_info *ivi)
^^^^^^
2892 {
2893 struct port_info *pi = netdev_priv(dev);
2894 struct adapter *adap = pi->adapter;
2895 struct vf_info *vfinfo;
2896
2897 if (vf >= adap->num_vfs)
^^^^^^^^^^^^^^^^^^^
2898 return -EINVAL;
2899 vfinfo = &adap->vfinfo[vf];
^^^^^^^^^^^^^^^^^^^^^^^^^^
There are 48 functions affected.
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c:8435 hclge_set_vf_vlan_filter() warn: can 'vfid' underflow 's32min-2147483646'
drivers/net/ethernet/freescale/enetc/enetc_pf.c:377 enetc_pf_set_vf_mac() warn: can 'vf' underflow 's32min-2147483646'
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:2899 cxgb4_mgmt_get_vf_config() warn: can 'vf' underflow 's32min-254'
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:2960 cxgb4_mgmt_set_vf_rate() warn: can 'vf' underflow 's32min-254'
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:3019 cxgb4_mgmt_set_vf_rate() warn: can 'vf' underflow 's32min-254'
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:3038 cxgb4_mgmt_set_vf_vlan() warn: can 'vf' underflow 's32min-254'
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:3086 cxgb4_mgmt_set_vf_link_state() warn: can 'vf' underflow 's32min-254'
drivers/net/ethernet/chelsio/cxgb/cxgb2.c:791 get_eeprom() warn: can 'i' underflow 's32min-(-4),0,4-s32max'
drivers/net/ethernet/broadcom/bnxt/bnxt_sriov.c:82 bnxt_set_vf_spoofchk() warn: can 'vf_id' underflow 's32min-65534'
drivers/net/ethernet/broadcom/bnxt/bnxt_sriov.c:164 bnxt_set_vf_trust() warn: can 'vf_id' underflow 's32min-65534'
drivers/net/ethernet/broadcom/bnxt/bnxt_sriov.c:186 bnxt_get_vf_config() warn: can 'vf_id' underflow 's32min-65534'
drivers/net/ethernet/broadcom/bnxt/bnxt_sriov.c:228 bnxt_set_vf_mac() warn: can 'vf_id' underflow 's32min-65534'
drivers/net/ethernet/broadcom/bnxt/bnxt_sriov.c:264 bnxt_set_vf_vlan() warn: can 'vf_id' underflow 's32min-65534'
drivers/net/ethernet/broadcom/bnxt/bnxt_sriov.c:293 bnxt_set_vf_bw() warn: can 'vf_id' underflow 's32min-65534'
drivers/net/ethernet/broadcom/bnxt/bnxt_sriov.c:333 bnxt_set_vf_link_state() warn: can 'vf_id' underflow 's32min-65534'
drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.c:2595 bnx2x_vf_op_prep() warn: can 'vfidx' underflow 's32min-63'
drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.c:2595 bnx2x_vf_op_prep() warn: can 'vfidx' underflow 's32min-63'
drivers/net/ethernet/broadcom/bnx2x/bnx2x_vfpf.c:2281 bnx2x_post_vf_bulletin() warn: can 'vf' underflow 's32min-63'
drivers/net/ethernet/broadcom/bnx2x/bnx2x_vfpf.c:2285 bnx2x_post_vf_bulletin() warn: can 'vf' underflow 's32min-63'
drivers/net/ethernet/broadcom/bnx2x/bnx2x_vfpf.c:2286 bnx2x_post_vf_bulletin() warn: can 'vf' underflow 's32min-63'
drivers/net/ethernet/broadcom/bnx2x/bnx2x_vfpf.c:2292 bnx2x_post_vf_bulletin() warn: can 'vf' underflow 's32min-63'
drivers/net/ethernet/broadcom/bnx2x/bnx2x_vfpf.c:2297 bnx2x_post_vf_bulletin() warn: can 'vf' underflow 's32min-63'
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c:1832 qlcnic_sriov_set_vf_mac() warn: can 'vf' underflow 's32min-254'
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c:1864 qlcnic_sriov_set_vf_tx_rate() warn: can 'vf' underflow 's32min-254'
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c:1937 qlcnic_sriov_set_vf_vlan() warn: can 'vf' underflow 's32min-254'
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c:2005 qlcnic_sriov_get_vf_config() warn: can 'vf' underflow 's32min-254'
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c:2036 qlcnic_sriov_set_vf_spoofchk() warn: can 'vf' underflow 's32min-254'
drivers/net/ethernet/emulex/benet/be_main.c:1914 be_get_vf_config() warn: can 'vf' underflow 's32min-65534'
drivers/net/ethernet/emulex/benet/be_main.c:1915 be_get_vf_config() warn: can 'vf' underflow 's32min-65534'
drivers/net/ethernet/emulex/benet/be_main.c:1922 be_set_vf_tvt() warn: can 'vf' underflow 's32min-65534'
drivers/net/ethernet/emulex/benet/be_main.c:1951 be_clear_vf_tvt() warn: can 'vf' underflow 's32min-65534'
drivers/net/ethernet/emulex/benet/be_main.c:2063 be_set_vf_tx_rate() warn: can 'vf' underflow 's32min-65534'
drivers/net/ethernet/emulex/benet/be_main.c:2091 be_set_vf_link_state() warn: can 'vf' underflow 's32min-65534'
drivers/net/ethernet/intel/ice/ice_virtchnl_pf.c:2609 ice_set_vf_port_vlan() warn: can 'vf_id' underflow 's32min-65534'
drivers/net/ethernet/intel/ice/ice_virtchnl_pf.c:3050 ice_get_vf_cfg() warn: can 'vf_id' underflow 's32min-65534'
drivers/net/ethernet/intel/ice/ice_virtchnl_pf.c:3103 ice_set_vf_spoofchk() warn: can 'vf_id' underflow 's32min-65534'
drivers/net/ethernet/intel/ice/ice_virtchnl_pf.c:3181 ice_set_vf_mac() warn: can 'vf_id' underflow 's32min-65534'
drivers/net/ethernet/intel/ice/ice_virtchnl_pf.c:3237 ice_set_vf_trust() warn: can 'vf_id' underflow 's32min-65534'
drivers/net/ethernet/intel/ice/ice_virtchnl_pf.c:3286 ice_set_vf_link_state() warn: can 'vf_id' underflow 's32min-65534'
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c:3919 i40e_validate_vf() warn: can 'vf_id' underflow 's32min-2147483646'
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c:3957 i40e_ndo_set_vf_mac() warn: can 'vf_id' underflow 's32min-2147483646'
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c:4104 i40e_ndo_set_vf_port_vlan() warn: can 'vf_id' underflow 's32min-2147483646'
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c:4263 i40e_ndo_set_vf_bw() warn: can 'vf_id' underflow 's32min-2147483646'
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c:4309 i40e_ndo_get_vf_config() warn: can 'vf_id' underflow 's32min-2147483646'
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c:4371 i40e_ndo_set_vf_link_state() warn: can 'vf_id' underflow 's32min-2147483646'
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c:4441 i40e_ndo_set_vf_spoofchk() warn: can 'vf_id' underflow 's32min-2147483646'
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c:4441 i40e_ndo_set_vf_spoofchk() warn: can 'vf_id' underflow 's32min-2147483646'
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c:4504 i40e_ndo_set_vf_trust() warn: can 'vf_id' underflow 's32min-2147483646'
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |\ \ \ \
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Haiyang Zhang says:
====================
hv_netvsc: Fix send indirection table offset
Fix send indirection table offset issues related to guest and
host bugs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
If negotiated NVSP version <= NVSP_PROTOCOL_VERSION_6, the offset may
be wrong (too small) due to a host bug. This can cause missing the
end of the send indirection table, and add multiple zero entries from
leading zeros before the data region. This bug adds extra burden on
channel 0.
So fix the offset by computing it from the data structure sizes. This
will ensure netvsc driver runs normally on unfixed hosts, and future
fixed hosts.
Fixes: 5b54dac856cb ("hyperv: Add support for virtual Receive Side Scaling (vRSS)")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |/ / / /
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
To reach the data region, the existing code adds offset in struct
nvsp_5_send_indirect_table on the beginning of this struct. But the
offset should be based on the beginning of its container,
struct nvsp_message. This bug causes the first table entry missing,
and adds an extra zero from the zero pad after the data region.
This can put extra burden on the channel 0.
So, correct the offset usage. Also add a boundary check to ensure
not reading beyond data region.
Fixes: 5b54dac856cb ("hyperv: Add support for virtual Receive Side Scaling (vRSS)")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
NET_RAW is less dangerous, so more likely to be available to a process,
so check it first to prevent some spurious logging.
This matches IP_TRANSPARENT which checks NET_RAW first.
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
The workqueue only exists for the primary PF. For other functions
we hit a WARN_ON in kernel/workqueue.c.
Fixes: 7c236c43b838 ("sfc: Add support for IEEE-1588 PTP")
Signed-off-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
If starting the transfer of a command suceeds but the transfer for the reply
fails, it is not enough to initiate killing the transfer for the
command may still be running. You need to wait for the killing to finish
before you can reuse URB and buffer.
Reported-and-tested-by: syzbot+711468aa5c3a1eabf863@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
kobject_put() should only be called in error path.
Fixes: b8eb718348b8 ("net-sysfs: Fix reference count leak in rx|netdev_queue_add_kobject")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jouni Hogander <jouni.hogander@unikie.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |\ \ \ \
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2019-11-20
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
For -stable v4.9:
('net/mlx5e: Fix set vf link state error flow')
For -stable v4.14
('net/mlxfw: Verify FSM error code translation doesn't exceed array size')
For -stable v4.19
('net/mlx5: Fix auto group size calculation')
For -stable v5.3
('net/mlx5e: Fix error flow cleanup in mlx5e_tc_tun_create_header_ipv4/6')
('net/mlx5e: Do not use non-EXT link modes in EXT mode')
('net/mlx5: Update the list of the PCI supported devices')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Array mlxfw_fsm_state_err_str contains value to string translation, when
values are provided by mlxfw_dev. If value is larger than
MLXFW_FSM_STATE_ERR_MAX, return "unknown error" as expected instead of
reading an address than exceed array size.
Fixes: 410ed13cae39 ("Add the mlxfw module for Mellanox firmware flash process")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Add the upcoming ConnectX-6 LX device ID.
Fixes: 85327a9c4150 ("net/mlx5: Update the list of the PCI supported devices")
Signed-off-by: Shani Shapp <shanish@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Once all the large flow groups (defined by the user when the flow table
is created - max_num_groups) were created, then all the following new
flow groups will have only one flow table entry, even though the flow table
has place to larger groups.
Fix the condition to prefer large flow group.
Fixes: f0d22d187473 ("net/mlx5_core: Introduce flow steering autogrouped flow table")
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Device that doesn't support IP-in-IP offloads has to filter csum and gso
offload support, otherwise kernel will conclude that device is capable of
offloading csum and gso for IP-in-IP tunnels and that might result in
IP-in-IP tunnel not functioning.
Fixes: 25948b87dda2 ("net/mlx5e: Support TSO and TX checksum offloads for IP-in-IP")
Signed-off-by: Marina Varshaver <marinav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
On some old Firmwares, connector type value was not supported, and value
read from FW was 0. For those, driver used link mode in order to set
connector type in link_ksetting.
After FW exposed the connector type, driver translated the value to ethtool
definitions. However, as 0 is a valid value, before returning PORT_OTHER,
driver run the check of link mode in order to maintain backward
compatibility.
Cited patch added support to EXT mode. With both features (connector type
and EXT link modes) ,if connector_type read from FW is 0 and EXT mode is
set, driver mistakenly compare EXT link modes to non-EXT link mode.
Fixed that by skipping this comparison if we are in EXT mode, as connector
type value is valid in this scenario.
Fixes: 6a897372417e ("net/mlx5: ethtool, Add ethtool support for 50Gbps per lane link modes")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Before this commit the ndo always returned success.
Fix that.
Fixes: 1ab2068a4c66 ("net/mlx5: Implement vports admin state backup/restore")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
When an ste hash table has too many collision we enlarge it
to a bigger hash table (rehash). Rehashing collision improvement
depends on the bytemask value. The more 1 bits we have in bytemask
means better spreading in the table.
Without this fix tables can grow in size without providing any
improvement which can lead to memory depletion and failures.
This patch will limit table rehash to reduce memory and improve
the performance.
Fixes: 41d07074154c ("net/mlx5: DR, Expose steering rule functionality")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
The byte mask fields affect on the hash index distribution,
when the byte mask is zero, the hash calculation will always
be equal to the same index.
To avoid unneeded rehash of hash tables mark the table to skip
rehash.
This is needed by the next patch which will limit table rehash
to reduce memory consumption.
Fixes: 41d07074154c ("net/mlx5: DR, Expose steering rule functionality")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
When creating a CQ, the CPU id is used for the vector value.
This would fail in-case the CPU id was higher than the maximum
vector value.
Fixes: 297cccebdc5a ("net/mlx5: DR, Expose an internal API to issue RDMA operations")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Mirred action parsing code in parse_tc_fdb_actions() first checks if
out_dev has same parent id, and only verifies that there is a pending encap
action that was parsed before. Recent change in vxlan module made function
netdev_port_same_parent_id() to return true when called for mlx5 eswitch
representor and vxlan device created explicitly on mlx5 representor
device (vxlan devices created with "external" flag without explicitly
specifying parent interface are not affected). With call to
netdev_port_same_parent_id() returning true, incorrect code path is chosen
and encap rules fail to offload because vxlan dev is not a valid eswitch
forwarding dev. Dmesg log of error:
[ 1784.389797] devices ens1f0_0 vxlan1 not on same switch HW, can't offload forwarding
In order to fix the issue, rearrange conditional in parse_tc_fdb_actions()
to check for pending encap action before checking if out_dev has the same
parent id.
Fixes: 0ce1822c2a08 ("vxlan: add adjacent link to limit depth level")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Current code uses the old method of prio encoding in
flow_cls_common_offload. Fix to follow the changes introduced in
commit ef01adae0e43 ("net: sched: use major priority number as hardware priority").
Fixes: fcb64c0f5640 ("net/mlx5: E-Switch, add ingress rate support")
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Be sure to release the neighbour in case of failures after successful
route lookup.
Fixes: 101f4de9dd52 ("net/mlx5e: Move TC tunnel offloading code to separate source file")
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Both rtl_work_func_t() and rtl8152_close() call napi_disable().
Since the two calls aren't protected by a lock, if the close
function starts executing before the work function, we can get into a
situation where the napi_disable() function is called twice in
succession (first by rtl8152_close(), then by set_carrier()).
In such a situation, the second call would loop indefinitely, since
rtl8152_close() doesn't call napi_enable() to clear the NAPI_STATE_SCHED
bit.
The rtl8152_close() function in turn issues a
cancel_delayed_work_sync(), and so it would wait indefinitely for the
rtl_work_func_t() to complete. Since rtl8152_close() is called by a
process holding rtnl_lock() which is requested by other processes, this
eventually leads to a system deadlock and crash.
Re-order the napi_disable() call to occur after the work function
disabling and urb cancellation calls are issued.
Change-Id: I6ef0b703fc214998a037a68f722f784e1d07815e
Reported-by: http://crbug.com/1017928
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |\ \ \ \ \
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Stefan Wahren says:
====================
net: qca_spi: Fix receive and reset issues
This small patch series fixes two major issues in the SPI driver for the
QCA700x.
It has been tested on a Charge Control C 300 (NXP i.MX6ULL +
2x QCA7000).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The reset counter is specific for every QCA700x chip. So move this
into the private driver struct. Otherwise we get unpredictable reset
behavior in setups with multiple QCA700x chips.
Fixes: 291ab06ecf67 (net: qualcomm: new Ethernet over SPI driver for QCA7000)
Signed-off-by: Stefan Wahren <stefan.wahren@in-tech.com>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |/ / / / /
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
When receiving many or larger packets, e.g. when doing a file download,
it was observed that the read buffer size register reports up to 4 bytes
more than the current define allows in the check.
If this is the case, then no data transfer is initiated to receive the
packets (and thus to empty the buffer) which results in a stall of the
interface.
These 4 bytes are a hardware generated frame length which is prepended
to the actual frame, thus we have to respect it during our check.
Fixes: 026b907d58c4 ("net: qca_spi: Add available buffer space verification")
Signed-off-by: Michael Heimpold <michael.heimpold@in-tech.com>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |\ \ \ \ \
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Juliet Kim says:
====================
Support both XIVE and XICS modes in ibmvnic
This series aims to support both XICS and XIVE with avoiding
a regression in behavior when a system runs in XICS mode.
Patch 1 reverts commit 11d49ce9f7946dfed4dcf5dbde865c78058b50ab
(“net/ibmvnic: Fix EOI when running in XIVE mode.”)
Patch 2 Ignore H_FUNCTION return from H_EOI to tolerate XIVE mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Reversion of commit 11d49ce9f7946dfed4dcf5dbde865c78058b50ab
(“net/ibmvnic: Fix EOI when running in XIVE mode.”) leaves us
calling H_EOI even in XIVE mode. That will fail with H_FUNCTION
because H_EOI is not supported in that mode. That failure is
harmless. Ignore it so we can use common code for both XICS and
XIVE.
Signed-off-by: Juliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |/ / / / /
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
This reverts commit 11d49ce9f7946dfed4dcf5dbde865c78058b50ab
(“net/ibmvnic: Fix EOI when running in XIVE mode.”) since that
has the unintended effect of changing the interrupt priority
and emits warning when running in legacy XICS mode.
Signed-off-by: Juliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |\ \ \ \ \
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Julian Wiedmann says:
====================
s390/qeth: fixes 2019-11-20
please apply two late qeth fixes to your net tree.
The first fixes a deadlock that can occur if a qeth device is set
offline while in the middle of processing deferred HW events.
The second patch converts the return value of an error path to
use -EIO, so that it can be passed back to userspace.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
When propagating IO errors back to userspace, one error path in
qeth_irq() currently returns '1' instead of a proper errno.
Fixes: 54daaca7024d ("s390/qeth: cancel cmd on early error")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |/ / / / /
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
The L2 bridgeport code uses the coarse 'conf_mutex' for guarding access
to its configuration state.
This can result in a deadlock when qeth_l2_stop_card() - called under the
conf_mutex - blocks on flush_workqueue() to wait for the completion of
pending bridgeport workers. Such workers would also need to aquire
the conf_mutex, stalling indefinitely.
Introduce a lock that specifically guards the bridgeport configuration,
so that the workers no longer need the conf_mutex.
Wrapping qeth_l2_promisc_to_bridge() in this fine-grained lock then also
fixes a theoretical race against a concurrent qeth_bridge_port_role_store()
operation.
Fixes: c0a2e4d10d93 ("s390/qeth: conclude all event processing before offlining a card")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Previously we will return directly if (!rt || !rt->fib6_nh.fib_nh_gw_family)
in function rt6_probe(), but after commit cc3a86c802f0
("ipv6: Change rt6_probe to take a fib6_nh"), the logic changed to
return if there is fib_nh_gw_family.
Fixes: cc3a86c802f0 ("ipv6: Change rt6_probe to take a fib6_nh")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | |/ / / /
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
kobject_init_and_add takes reference even when it fails. This has
to be given up by the caller in error handling. Otherwise memory
allocated by kobject_init_and_add is never freed. Originally found
by Syzkaller:
BUG: memory leak
unreferenced object 0xffff8880679f8b08 (size 8):
comm "netdev_register", pid 269, jiffies 4294693094 (age 12.132s)
hex dump (first 8 bytes):
72 78 2d 30 00 36 20 d4 rx-0.6 .
backtrace:
[<000000008c93818e>] __kmalloc_track_caller+0x16e/0x290
[<000000001f2e4e49>] kvasprintf+0xb1/0x140
[<000000007f313394>] kvasprintf_const+0x56/0x160
[<00000000aeca11c8>] kobject_set_name_vargs+0x5b/0x140
[<0000000073a0367c>] kobject_init_and_add+0xd8/0x170
[<0000000088838e4b>] net_rx_queue_update_kobjects+0x152/0x560
[<000000006be5f104>] netdev_register_kobject+0x210/0x380
[<00000000e31dab9d>] register_netdevice+0xa1b/0xf00
[<00000000f68b2465>] __tun_chr_ioctl+0x20d5/0x3dd0
[<000000004c50599f>] tun_chr_ioctl+0x2f/0x40
[<00000000bbd4c317>] do_vfs_ioctl+0x1c7/0x1510
[<00000000d4c59e8f>] ksys_ioctl+0x99/0xb0
[<00000000946aea81>] __x64_sys_ioctl+0x78/0xb0
[<0000000038d946e5>] do_syscall_64+0x16f/0x580
[<00000000e0aa5d8f>] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[<00000000285b3d1a>] 0xffffffffffffffff
Cc: David Miller <davem@davemloft.net>
Cc: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Jouni Hogander <jouni.hogander@unikie.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
