aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* Merge branch 'master' of ↵David S. Miller2009-11-0823-145/+259
|\ | | | | | | | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/can/usb/ems_usb.c
| * net/fsl_pq_mdio: add module license GPLSebastian Siewior2009-11-081-0/+1
| | | | | | | | | | | | | | | | or it will taint the kernel and fail to load becuase of_address_to_resource() is GPL only. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
| * can: fix WARN_ON dump in net/core/rtnetlink.c:rtmsg_ifinfo()Wolfgang Grandegger2009-11-081-0/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | On older kernels, e.g. 2.6.27, a WARN_ON dump in rtmsg_ifinfo() is thrown when the CAN device is registered due to insufficient skb space, as reported by various users. This patch adds the rtnl_link_ops "get_size" to fix the problem. I think this patch is required for more recent kernels as well, even if no WARN_ON dumps are triggered. Maybe we also need "get_xstats_size" for the CAN xstats. Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * can: should not use __dev_get_by_index() without locksEric Dumazet2009-11-081-7/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | bcm_proc_getifname() is called with RTNL and dev_base_lock not held. It calls __dev_get_by_index() without locks, and this is illegal (might crash) Close the race by holding dev_base_lock and copying dev->name in the protected section. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net> Signed-off-by: David S. Miller <davem@davemloft.net>
| * hisax: remove bad udelay call to fix build error on ARMMartin Michlmayr2009-11-061-11/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The hisax ISDN driver fails to build on ARM with CONFIG_HISAX_ELSA: | drivers/built-in.o: In function `modem_set_dial': | drivers/isdn/hisax/elsa_ser.c:535: undefined reference to `__bad_udelay' | drivers/isdn/hisax/elsa_ser.c:544: undefined reference to `__bad_udelay' | drivers/built-in.o: In function `modem_set_init': | drivers/isdn/hisax/elsa_ser.c:486: undefined reference to `__bad_udelay' | [...] According to the comment in arch/arm/include/asm/delay.h, __bad_udelay is specifically designed on ARM to produce a build failure when udelay is called with a value > 2000. Signed-off-by: Martin Michlmayr <tbm@cyrius.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * ipip: Fix handling of DF packets when pmtudisc is OFFHerbert Xu2009-11-061-15/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | RFC 2003 requires the outer header to have DF set if DF is set on the inner header, even when PMTU discovery is off for the tunnel. Our implementation does exactly that. For this to work properly the IPIP gateway also needs to engate in PMTU when the inner DF bit is set. As otherwise the original host would not be able to carry out its PMTU successfully since part of the path is only visible to the gateway. Unfortunately when the tunnel PMTU discovery setting is off, we do not collect the necessary soft state, resulting in blackholes when the original host tries to perform PMTU discovery. This problem is not reproducible on the IPIP gateway itself as the inner packet usually has skb->local_df set. This is not correctly cleared (an unrelated bug) when the packet passes through the tunnel, which allows fragmentation to occur. For hosts behind the IPIP gateway it is readily visible with a simple ping. This patch fixes the problem by performing PMTU discovery for all packets with the inner DF bit set, regardless of the PMTU discovery setting on the tunnel itself. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
| * qlge: Set PCIe reset type for EEH to fundamental.Ron Mercer2009-11-061-0/+2
| | | | | | | | | | | | | | This device requires a fundamental reset when recovering from EEH. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * qlge: Fix early exit from mbox cmd complete wait.Ron Mercer2009-11-061-1/+1
| | | | | | | | | | | | | | | | | | This line was accidentally left out of the previous commit # da03945140a035a2962f7f93e359085596f20499 ("qlge: Fix firmware mailbox command timeout."). Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * ixgbe: fix traffic hangs on Tx with ioatdma loadedDon Skidmore2009-11-061-4/+23
| | | | | | | | | | | | | | | | | | | | | | | | When ioatdma was loaded we we were unable to transmit traffic. We weren't using the correct registers in ixgbe_update_tx_dca for 82599 systems. Likewise in ixgbe_configure_tx() we weren't disabling the arbiter before modifying MTQC. Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * ixgbe: Fix checking TFCS register for TXOFF status when DCB is enabledYi Zou2009-11-061-1/+51
| | | | | | | | | | | | | | | | | | | | | | | | When DCB is enabled, the ixgbe_check_tx_hang() should check the corresponding TC's TXOFF in TFCS based on the TC that the tx ring belongs to. Adds a function to map from the tx_ring hw reg_idx to the correspodning TC and read TFCS accordingly. Signed-off-by: Yi Zou <yi.zou@intel.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * ixgbe: Fix gso_max_size for 82599 when DCB is enabledYi Zou2009-11-061-1/+4
| | | | | | | | | | | | | | | | | | The 32k gso_max_size when DCB is enabled is for 82598 only, not for 82599. Signed-off-by: Yi Zou <yi.zou@intel.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * macsonic: fix crash on PowerBook 520Finn Thain2009-11-061-57/+60
| | | | | | | | | | | | | | | | | | No-one seems to know where the PowerBook 500 series store their ethernet MAC addresses. So, rather than crash, use a MAC address from the SONIC CAM. Failing that, generate a random one. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
| * NET: cassini, fix lock imbalanceJiri Slaby2009-11-061-2/+3
| | | | | | | | | | | | | | | | Stanse found that one error path in cas_open omits to unlock pm_mutex. Fix that. Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * ems_usb: Fix byte order issues on big endian machinesSebastian Haas2009-11-061-1/+4
| | | | | | | | | | | | | | | | CPC-USB is using a ARM7 core with little endian byte order. The "id" field in can_msg needs byte order conversion from/to CPU byte order. Signed-off-by: Sebastian Haas <haas@ems-wuensche.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * be2net: Bug fix to send config commands to hardware after netdev_registerAjit Khaparde2009-11-061-12/+12
| | | | | | | | | | | | | | | | | | | | | | Sending config commands to be2 hardware before netdev_register is completed, is sometimes causing the async link notification to arrive even before the driver is ready to handle it. The commands for vlan config and flow control settings can infact wait till be_open. This patch takes care of that. Signed-off-by: Ajit Khaparde <ajitk@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * be2net: fix to set proper flow control on resumeAjit Khaparde2009-11-063-4/+14
| | | | | | | | | | | | | | | | | | | | If be2 goes into suspend after a user changes the flow control settings, we are not programming them back after resume. This patch takes care of it. We now get the flow control settings before going to suspend mode and then apply them during resume. Signed-off-by: Ajit Khaparde <ajitk@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * Merge branch 'master' of ↵David S. Miller2009-11-068-25/+25
| |\ | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
| | * rt2x00: Don't queue ieee80211 work after USB removalSean Cross2009-11-063-7/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | This prevents the rt2x00 driver from queueing ieee80211 work after the   USB card has been removed, preventing a kernel panic. Signed-off-by: Sean Cross <sean@chumby.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| | * Revert "ipw2200: fix oops on missing firmware"John W. Linville2009-11-064-16/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This reverts commit e6c5fc53d0f44a772398402ee8a1879818e42b4e. Based on this regression report: Date: Thu, 05 Nov 2009 15:59:16 +0100 From: Holger Schurig <holgerschurig@gmail.com> To: linux-wireless@vger.kernel.org Subject: BUG: oops when "rmmod ipw2200" This happened on wireless-testing v2.6.32-rc6-41575-g5e68bfb. I modprobed ipw2200, put it into monitor mode, used tshark a while to monitor, then I stopped tshark, "ifconfig eth2 down" and finally "rmmod ipw2200", and voila: [ 917.189620] ------------[ cut here ]------------ [ 917.189717] kernel BUG at net/wireless/core.c:543! [ 917.189805] invalid opcode: 0000 [#1] PREEMPT SMP [ 917.190002] last sysfs file: /sys/devices/pci0000:00/0000:00:1e.0/0000:02:0d.0/firmware/0000:02:0d.0/loading [ 917.190136] Modules linked in: lib80211_crypt_wep ipw2200(-) libipw lib80211 ath5k mac80211 ath cfg80211 psmouse uhci_hcd [ 917.190680] [ 917.190759] Pid: 1763, comm: rmmod Not tainted (2.6.32-rc6-wl #26) Amilo M1425 [ 917.190886] EIP: 0060:[<f8accf34>] EFLAGS: 00010202 CPU: 0 [ 917.190992] EIP is at wiphy_unregister+0xd3/0x175 [cfg80211] [ 917.191083] EAX: f601d4c4 EBX: 00000000 ECX: 00000000 EDX: f79e8600 [ 917.191176] ESI: f601d400 EDI: f95b4350 EBP: f6009eb4 ESP: f6009e8c [ 917.191269] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068 [ 917.191360] Process rmmod (pid: 1763, ti=f6008000 task=f79e8130 task.ti=f6008000) [ 917.191486] Stack: [ 917.191562] f601d5a0 f601d484 f6460e98 f6009ea0 c01407ee f6009eb8 00000246 f64604c0 [ 917.191916] <0> f6460e5c f95b4350 f6009ec0 f94fd030 f6460e98 f6009edc f95a9d4f f787bc00 [ 917.192100] <0> f787bc58 f787bc00 f95b4350 f95b4350 f6009ee8 c0207fca f787bc58 f6009ef8 [ 917.192100] Call Trace: [ 917.192100] [<c01407ee>] ? trace_hardirqs_on+0xb/0xd [ 917.192100] [<f94fd030>] ? unregister_ieee80211+0xe/0x27 [libipw] [ 917.192100] [<f95a9d4f>] ? ipw_pci_remove+0x59/0x227 [ipw2200] [ 917.192100] [<c0207fca>] ? pci_device_remove+0x19/0x39 [ 917.192100] [<c02b93a4>] ? __device_release_driver+0x59/0x9d [ 917.192100] [<c02b944f>] ? driver_detach+0x67/0x85 [ 917.192100] [<c02b88d6>] ? bus_remove_driver+0x69/0x85 [ 917.192100] [<c02b9878>] ? driver_unregister+0x4d/0x54 [ 917.192100] [<c02081c3>] ? pci_unregister_driver+0x28/0x71 [ 917.192100] [<f95a9cf4>] ? ipw_exit+0x1c/0x1e [ipw2200] [ 917.192100] [<c0148e2b>] ? sys_delete_module+0x192/0x1ef [ 917.192100] [<c0162cdb>] ? remove_vma+0x52/0x58 [ 917.192100] [<c01028bb>] ? sysenter_exit+0xf/0x18 [ 917.192100] [<c0102888>] ? sysenter_do_call+0x12/0x36 [ 917.192100] Code: 74 07 e8 81 bc 8c c7 eb c8 8d 55 e0 89 f8 e8 d6 6d 66 c7 8b 45 dc 31 d2 e8 81 cc 8c c7 8d 86 c4 00 00 00 39 86 c4 00 00 00 74 04 <0f> 0b eb fe 8b 45 dc 8d 5e 0c e8 5a cc 8c c7 8b 86 94 03 00 00 [ 917.192100] EIP: [<f8accf34>] wiphy_unregister+0xd3/0x175 [cfg80211] SS:ESP 0068:f6009e8c [ 917.203718] ---[ end trace bcaaf449945a5100 ]--- Signed-off-by: John W. Linville <linville@tuxdriver.com>
| | * rtl8187: Fix kernel oops when device is removed when LEDS enabledLarry Finger2009-11-041-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | As reported by Rick Farina (sidhayn@gmail.com), removing the RTL8187 USB stick, or unloading the driver rtl8187 using rmmod will cause a kernel oops. There are at least two forms of the failure, (1) BUG: Scheduling while atomic, and (2) a fatal kernel page fault. This problem is reported in Bugzilla #14539. This problem does not occur for kernel 2.6.31, but does for 2.6.32-rc2, thus it is technically a regression; however, bisection did not locate any faulty patch. The fix was found by comparing the faulty code in rtl8187 with p54usb. My interpretation is that the handling of work queues in mac80211 changed enough to the LEDs to be unregistered before tasks on the work queues are cancelled. Previously, these actions could be done in either order. (Herton Ronaldo Krzesinski <herton@mandriva.com.br> reports that the code is the same in 2.6.31, so this may be a candidate for 2.6.31.x. -- JWL) Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Reported-by: Rick Farina <sidhayn@gmail.com> Tested-by: Rick Farina <sidhayn@gmail.com> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
| * | netfilter: xt_connlimit: fix regression caused by zero family valueJan Engelhardt2009-11-061-6/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit v2.6.28-rc1~717^2~109^2~2 was slightly incomplete; not all instances of par->match->family were changed to par->family. References: http://bugzilla.netfilter.org/show_bug.cgi?id=610 Signed-off-by: Jan Engelhardt <jengelh@medozas.de> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | xfrm: SAD entries do not expire correctly after suspend-resumeYury Polyanskiy2009-11-082-14/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This fixes the following bug in the current implementation of net/xfrm: SAD entries timeouts do not count the time spent by the machine in the suspended state. This leads to the connectivity problems because after resuming local machine thinks that the SAD entry is still valid, while it has already been expired on the remote server. The cause of this is very simple: the timeouts in the net/xfrm are bound to the old mod_timer() timers. This patch reassigns them to the CLOCK_REALTIME hrtimer. I have been using this version of the patch for a few months on my machines without any problems. Also run a few stress tests w/o any issues. This version of the patch uses tasklet_hrtimer by Peter Zijlstra (commit 9ba5f0). This patch is against 2.6.31.4. Please CC me. Signed-off-by: Yury Polyanskiy <polyanskiy@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | net/compat_ioctl: support SIOCWANDEVArnd Bergmann2009-11-082-17/+47
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds compat_ioctl support for SIOCWANDEV, which has always been missing. The definition of struct compat_ifreq was missing an ifru_settings fields that is needed to support SIOCWANDEV, so add that and clean up the whitespace damage in the struct definition. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | net, compat_ioctl: fix SIOCGMII ioctlsArnd Bergmann2009-11-081-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SIOCGMIIPHY and SIOCGMIIREG return data through ifreq, so it needs to be converted on the way out as well. SIOCGIFPFLAGS is unused, but has the same problem in theory. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | udp: multicast RX should increment SNMP/sk_drops counter in allocation failuresEric Dumazet2009-11-082-2/+18
| | | | | | | | | | | | | | | | | | | | | When skb_clone() fails, we should increment sk_drops and SNMP counters. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | ipv6: udp: Optimise multicast receptionEric Dumazet2009-11-081-24/+47
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | IPV6 UDP multicast rx path is a bit complex and can hold a spinlock for a long time. Using a small (32 or 64 entries) stack of socket pointers can help to perform expensive operations (skb_clone(), udp_queue_rcv_skb()) outside of the lock, in most cases. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | ipv4: udp: Optimise multicast receptionEric Dumazet2009-11-081-26/+50
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UDP multicast rx path is a bit complex and can hold a spinlock for a long time. Using a small (32 or 64 entries) stack of socket pointers can help to perform expensive operations (skb_clone(), udp_queue_rcv_skb()) outside of the lock, in most cases. It's also a base for a future RCU conversion of multicast recption. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Lucian Adrian Grijincu <lgrijincu@ixiacom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | ipv6: udp: optimize unicast RX pathEric Dumazet2009-11-081-3/+109
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We first locate the (local port) hash chain head If few sockets are in this chain, we proceed with previous lookup algo. If too many sockets are listed, we take a look at the secondary (port, address) hash chain. We choose the shortest chain and proceed with a RCU lookup on the elected chain. But, if we chose (port, address) chain, and fail to find a socket on given address, we must try another lookup on (port, in6addr_any) chain to find sockets not bound to a particular IP. -> No extra cost for typical setups, where the first lookup will probabbly be performed. RCU lookups everywhere, we dont acquire spinlock. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | ipv4: udp: optimize unicast RX pathEric Dumazet2009-11-081-3/+112
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We first locate the (local port) hash chain head If few sockets are in this chain, we proceed with previous lookup algo. If too many sockets are listed, we take a look at the secondary (port, address) hash chain we added in previous patch. We choose the shortest chain and proceed with a RCU lookup on the elected chain. But, if we chose (port, address) chain, and fail to find a socket on given address, we must try another lookup on (port, INADDR_ANY) chain to find socket not bound to a particular IP. -> No extra cost for typical setups, where the first lookup will probabbly be performed. RCU lookups everywhere, we dont acquire spinlock. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | udp: secondary hash on (local port, local address)Eric Dumazet2009-11-084-9/+53
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Extends udp_table to contain a secondary hash table. socket anchor for this second hash is free, because UDP doesnt use skc_bind_node : We define an union to hold both skc_bind_node & a new hlist_nulls_node udp_portaddr_node udp_lib_get_port() inserts sockets into second hash chain (additional cost of one atomic op) udp_lib_unhash() deletes socket from second hash chain (additional cost of one atomic op) Note : No spinlock lockdep annotation is needed, because lock for the secondary hash chain is always get after lock for primary hash chain. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | udp: split sk_hash into two u16 hashesEric Dumazet2009-11-084-9/+51
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Union sk_hash with two u16 hashes for udp (no extra memory taken) One 16 bits hash on (local port) value (the previous udp 'hash') One 16 bits hash on (local address, local port) values, initialized but not yet used. This second hash is using jenkin hash for better distribution. Because the 'port' is xored later, a partial hash is performed on local address + net_hash_mix(net) Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | udp: add a counter into udp_hslotEric Dumazet2009-11-082-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Adds a counter in udp_hslot to keep an accurate count of sockets present in chain. This will permit to upcoming UDP lookup algo to chose the shortest chain when secondary hash is added. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | net/appletalk: using compat_ptr needs inclusion of linux/compat.hStephen Rothwell2009-11-081-0/+1
| | | | | | | | | | | | | | | Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | can: Driver for the Microchip MCP251x SPI CAN controllersChristian Pellegrin2009-11-084-0/+1207
| | | | | | | | | | | | | | | | | | Signed-off-by: Christian Pellegrin <chripell@fsfe.org> Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | net: Support specifying the network namespace upon device creation.Eric W. Biederman2009-11-087-23/+50
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There is no good reason to not support userspace specifying the network namespace during device creation, and it makes it easier to create a network device and pass it to a child network namespace with a well known name. We have to be careful to ensure that the target network namespace for the new device exists through the life of the call. To keep that logic clear I have factored out the network namespace grabbing logic into rtnl_link_get_net. In addtion we need to continue to pass the source network namespace to the rtnl_link_ops.newlink method so that we can find the base device source network namespace. Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
* | | appletalk/ddp.c: Neaten checksum functionJoe Perches2009-11-081-7/+2
| | | | | | | | | | | | | | | | | | | | | atalk_sum_partial can now use the rol16 function in bitops.h Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | ipv6: avoid dev_hold()/dev_put() in rawv6_bind()Eric Dumazet2009-11-081-12/+11
| | | | | | | | | | | | | | | | | | | | | Using RCU helps not touching device refcount in rawv6_bind() Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | gianfar: Fix compiler and sparse warningsAnton Vorontsov2009-11-082-11/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit fba4ed030cfae7efdb6b79a57b0c5a9d72c9de83 ("gianfar: Add Multiple Queue Support") introduced the following warnings: CHECK gianfar.c gianfar.c:333:8: warning: incorrect type in assignment (different address spaces) gianfar.c:333:8: expected unsigned int [usertype] *baddr gianfar.c:333:8: got unsigned int [noderef] <asn:2>*<noident> [... 67 lines skipped ...] gianfar.c:2565:3: warning: incorrect type in argument 1 (different type sizes) gianfar.c:2565:3: expected unsigned long const *addr gianfar.c:2565:3: got unsigned int *<noident> CC gianfar.o gianfar.c: In function 'gfar_probe': gianfar.c:985: warning: passing argument 1 of 'find_next_bit' from incompatible pointer type gianfar.c:985: warning: passing argument 1 of 'find_next_bit' from incompatible pointer type gianfar.c:993: warning: passing argument 1 of 'find_next_bit' from incompatible pointer type gianfar.c:993: warning: passing argument 1 of 'find_next_bit' from incompatible pointer type gianfar.c: In function 'gfar_configure_coalescing': gianfar.c:1680: warning: passing argument 1 of 'find_next_bit' from incompatible pointer type gianfar.c:1680: warning: passing argument 1 of 'find_next_bit' from incompatible pointer type gianfar.c:1688: warning: passing argument 1 of 'find_next_bit' from incompatible pointer type gianfar.c:1688: warning: passing argument 1 of 'find_next_bit' from incompatible pointer type gianfar.c: In function 'gfar_poll': gianfar.c:2565: warning: passing argument 1 of 'find_next_bit' from incompatible pointer type gianfar.c:2565: warning: passing argument 1 of 'find_next_bit' from incompatible pointer type gianfar.c:2566: warning: passing argument 2 of 'test_bit' from incompatible pointer type gianfar.c:2585: warning: passing argument 2 of 'set_bit' from incompatible pointer type Following warnings left unfixed (looks like sparse doesn't like locks in loops, so __acquires/__releases() doesn't help): gianfar.c:441:40: warning: context imbalance in 'lock_rx_qs': wrong count at exit gianfar.c:441:40: context '<noident>': wanted 0, got 1 gianfar.c:449:40: warning: context imbalance in 'lock_tx_qs': wrong count at exit gianfar.c:449:40: context '<noident>': wanted 0, got 1 gianfar.c:458:3: warning: context imbalance in 'unlock_rx_qs': __context__ statement expected different context gianfar.c:458:3: context '<noident>': wanted >= 0, got -1 gianfar.c:466:3: warning: context imbalance in 'unlock_tx_qs': __context__ statement expected different context gianfar.c:466:3: context '<noident>': wanted >= 0, got -1 Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | fsl_pq_mdio: Fix compiler/sparse warnings (part 2)Anton Vorontsov2009-11-081-4/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch fixes following warnings: fsl_pq_mdio.c:112:38: warning: cast adds address space to expression (<asn:2>) fsl_pq_mdio.c:124:38: warning: cast adds address space to expression (<asn:2>) fsl_pq_mdio.c:133:38: warning: cast adds address space to expression (<asn:2>) fsl_pq_mdio.c:414:11: warning: cast adds address space to expression (<asn:2>) Instead of adding __force all over the place, introduce convenient fsl_pq_mdio_get_regs() call that does the ugly casting just once. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | fsl_pq_mdio: Fix compiler/sparse warnings (part 1)Anton Vorontsov2009-11-081-19/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 1d2397d742b7a2b39b2f09dd9da3b9d1463f55e9 ("fsl_pq_mdio: Add Suport for etsec2.0 devices") introduced the following warnings: CHECK fsl_pq_mdio.c fsl_pq_mdio.c:287:22: warning: incorrect type in initializer (different base types) fsl_pq_mdio.c:287:22: expected unknown type 11 const *__mptr fsl_pq_mdio.c:287:22: got unsigned long long [unsigned] [assigned] [usertype] addr fsl_pq_mdio.c:287:19: warning: incorrect type in assignment (different base types) fsl_pq_mdio.c:287:19: expected unsigned long long [unsigned] [usertype] ioremap_miimcfg fsl_pq_mdio.c:287:19: got struct fsl_pq_mdio *<noident> CC fsl_pq_mdio.o fsl_pq_mdio.c: In function 'fsl_pq_mdio_probe': fsl_pq_mdio.c:287: warning: initialization makes pointer from integer without a cast fsl_pq_mdio.c:287: warning: assignment makes integer from pointer without a cast These warnings are not easy to fix without ugly __force casts. So, instead of introducing the casts, rework the code to substitute an offset from an already mapped area. This makes the code a lot simpler and less duplicated. Plus, from now on we don't actually map reserved registers on non-etsec2.0 devices, so we have more chances to catch programming errors. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | rtnetlink: CleanupsEric Dumazet2009-11-071-31/+23
| | | | | | | | | | | | | | | | | | | | | Pure cleanups patch Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | net: kill proto_ops wrapperArnd Bergmann2009-11-071-83/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | All users of wrapped proto_ops are now gone, so we can safely remove the wrappers as well. Cc: David S. Miller <davem@davemloft.net> Cc: netdev@vger.kernel.org Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | net/x25: push BKL usage into x25_protoArnd Bergmann2009-11-071-11/+60
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The x25 driver uses lock_kernel() implicitly through its proto_ops wrapper. The makes the usage explicit in order to get rid of that wrapper and to better document the usage of the BKL. The next step should be to get rid of the usage of the BKL in x25 entirely, which requires understanding what data structures need serialized accesses. Cc: Henner Eisen <eis@baty.hanse.de> Cc: David S. Miller <davem@davemloft.net> Cc: linux-x25@vger.kernel.org Cc: netdev@vger.kernel.org Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | net/irda: push BKL into proto_opsArnd Bergmann2009-11-071-107/+224
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The irda driver uses the BKL implicitly in its protocol operations. Replace the wrapped proto_ops with explicit lock_kernel() calls makes the usage more obvious and shrinks the size of the object code. The calls t lock_kernel() should eventually all be replaced by other serialization methods, which requires finding out The calls t lock_kernel() should eventually all be replaced by other serialization methods, which requires finding out which data actually needs protection. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | net/ipx: push down BKL into a ipx_dgram_opsArnd Bergmann2009-11-071-8/+46
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Making the BKL usage explicit in ipx makes it more obvious where it is used, reduces code size and helps getting rid of the BKL in common code. I did not analyse how to kill lock_kernel from ipx entirely, this will involve either proving that it's not needed, or replacing with a proper mutex or spinlock, after finding out which data structures are protected by the lock. Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net> Cc: David S. Miller <davem@davemloft.net> Cc: Stephen Hemminger <shemminger@vyatta.com> Cc: netdev@vger.kernel.org Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | net/appletalk: push down BKL into a atalk_dgram_opsArnd Bergmann2009-11-071-28/+77
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Making the BKL usage explicit in appletalk makes it more obvious where it is used, reduces code size and helps getting rid of the BKL in common code. I did not analyse how to kill lock_kernel from appletalk entirely, this will involve either proving that it's not needed, or replacing with a proper mutex or spinlock, after finding out which data structures are protected by the lock. Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net> Cc: David S. Miller <davem@davemloft.net> Cc: Stephen Hemminger <shemminger@vyatta.com> Cc: netdev@vger.kernel.org Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | atl1c: change atl1c_buffer struct and restructure clean atl1c_buffer procedureJie Yang2009-11-072-45/+61
| | | | | | | | | | | | | | | | | | | | | | | | | | | change atl1c_buffer struct, use "u16 flags" instead of "u16 state" to store more infomation for atl1c_buffer, and restructure clean atl1c_buffer procedure, add common api atl1c_clean_buffer. Signed-off-by: Jie Yang <jie.yang@atheros.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | net: Replace old style lock initializerThomas Gleixner2009-11-071-1/+1
| | | | | | | | | | | | | | | | | | | | | SPIN_LOCK_UNLOCKED is deprecated. Use DEFINE_SPINLOCK instead. Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | net: compat: No need to define IFHWADDRLEN and IFNAMSIZ twice.David S. Miller2009-11-061-2/+0
| | | | | | | | | | | | | | | | | | | | | It's defined colloqually in linux/if.h and linux/compat.h includes that. Signed-off-by: David S. Miller <davem@davemloft.net>
* | | net, compat_ioctl: handle more ioctls correctlyArnd Bergmann2009-11-061-14/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The MII ioctls and SIOCSIFNAME need to go through ifsioc conversion, which they never did so far. Some others are not implemented in the native path, so we can just return -EINVAL directly. Add IFSLAVE ioctls to the EINVAL list and move it to the end to optimize the code path for the common case. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit (git 2.34.1) at 2025-02-25 22:10:52 +0000