aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net/ethernet/freescale/fec_main.c
Commit message (Collapse)AuthorAgeFilesLines
* net: fec: Fix temporary RMII clock reset on link upLaurent Badel2021-01-261-2/+4
| | | | | | | | | | | | | | | | | fec_restart() does a hard reset of the MAC module when the link status changes to up. This temporarily resets the R_CNTRL register which controls the MII mode of the ENET_OUT clock. In the case of RMII, the clock frequency momentarily drops from 50MHz to 25MHz until the register is reconfigured. Some link partners do not tolerate this glitch and invalidate the link causing failure to establish a stable link when using PHY polling mode. Since as per IEEE802.3 the criteria for link validity are PHY-specific, what the partner should tolerate cannot be assumed, so avoid resetting the MII clock by using software reset instead of hardware reset when the link is up. This is generally relevant only if the SoC provides the clock to an external PHY and the PHY is configured for RMII. Signed-off-by: Laurent Badel <laurentbadel@eaton.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: fec: put child node on error pathPan Bian2021-01-221-1/+2
| | | | | | | | | Also decrement the reference count of child device on error path. Fixes: 3e782985cb3c ("net: ethernet: fec: Allow configuration of MDIO bus speed") Signed-off-by: Pan Bian <bianpan2016@163.com> Link: https://lore.kernel.org/r/20210120122037.83897-1-bianpan2016@163.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: fec: Fix reference count leak in fec series opsZhang Qilong2020-11-161-7/+5
| | | | | | | | | | | | | | | pm_runtime_get_sync() will increment pm usage at first and it will resume the device later. If runtime of the device has error or device is in inaccessible state(or other error state), resume operation will fail. If we do not call put operation to decrease the reference, it will result in reference count leak. Moreover, this device cannot enter the idle state and always stay busy or other non-idle state later. So we fixed it by replacing it with pm_runtime_resume_and_get. Fixes: 8fff755e9f8d0 ("net: fec: Ensure clocks are enabled while using mdio bus") Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: fec: fix MDIO probing for some FEC hardware blocksGreg Ungerer2020-10-301-13/+16
| | | | | | | | | | | | | | | | | | | | Some (apparently older) versions of the FEC hardware block do not like the MMFR register being cleared to avoid generation of MII events at initialization time. The action of clearing this register results in no future MII events being generated at all on the problem block. This means the probing of the MDIO bus will find no PHYs. Create a quirk that can be checked at the FECs MII init time so that the right thing is done. The quirk is set as appropriate for the FEC hardware blocks that are known to need this. Fixes: f166f890c8f0 ("net: ethernet: fec: Replace interrupt driven MDIO with polled IO") Signed-off-by: Greg Ungerer <gerg@linux-m68k.org> Acked-by: Fugang Duan <fugand.duan@nxp.com> Tested-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com> Link: https://lore.kernel.org/r/20201028052232.1315167-1-gerg@linux-m68k.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski2020-10-151-7/+28
|\ | | | | | | | | | | | | | | | | | | Minor conflicts in net/mptcp/protocol.h and tools/testing/selftests/net/Makefile. In both cases code was added on both sides in the same place so just keep both. Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * net: fec: Fix phy_device lookup for phy_reset_after_clk_enable()Marek Vasut2020-10-121-2/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The phy_reset_after_clk_enable() is always called with ndev->phydev, however that pointer may be NULL even though the PHY device instance already exists and is sufficient to perform the PHY reset. This condition happens in fec_open(), where the clock must be enabled first, then the PHY must be reset, and then the PHY IDs can be read out of the PHY. If the PHY still is not bound to the MAC, but there is OF PHY node and a matching PHY device instance already, use the OF PHY node to obtain the PHY device instance, and then use that PHY device instance when triggering the PHY reset. Fixes: 1b0a83ac04e3 ("net: fec: add phy_reset_after_clk_enable() support") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com> Cc: David S. Miller <davem@davemloft.net> Cc: NXP Linux Team <linux-imx@nxp.com> Cc: Richard Leitner <richard.leitner@skidata.com> Cc: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
| * net: fec: Fix PHY init after phy_reset_after_clk_enable()Marek Vasut2020-10-091-5/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The phy_reset_after_clk_enable() does a PHY reset, which means the PHY loses its register settings. The fec_enet_mii_probe() starts the PHY and does the necessary calls to configure the PHY via PHY framework, and loads the correct register settings into the PHY. Therefore, fec_enet_mii_probe() should be called only after the PHY has been reset, not before as it is now. Fixes: 1b0a83ac04e3 ("net: fec: add phy_reset_after_clk_enable() support") Reviewed-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Richard Leitner <richard.leitner@skidata.com> Signed-off-by: Marek Vasut <marex@denx.de> Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com> Cc: David S. Miller <davem@davemloft.net> Cc: NXP Linux Team <linux-imx@nxp.com> Cc: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* | net: ethernet: fec: remove redundant null check before clk_disable_unprepare()Zhang Changzhong2020-09-071-2/+1
|/ | | | | | | | | | | Because clk_prepare_enable() and clk_disable_unprepare() already checked NULL clock parameter, so the additional checks are unnecessary, just remove them. Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com> Acked-by: Fugang Duan <fugang.duan@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* net: fec: correct the error path for regulator disable in probeFugang Duan2020-08-141-2/+2
| | | | | | | | Correct the error path for regulator disable. Fixes: 9269e5560b26 ("net: fec: add phy-reset-gpios PROBE_DEFER check") Signed-off-by: Fugang Duan <fugang.duan@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netDavid S. Miller2020-07-251-6/+17
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The UDP reuseport conflict was a little bit tricky. The net-next code, via bpf-next, extracted the reuseport handling into a helper so that the BPF sk lookup code could invoke it. At the same time, the logic for reuseport handling of unconnected sockets changed via commit efc6b6f6c3113e8b203b9debfb72d81e0f3dcace which changed the logic to carry on the reuseport result into the rest of the lookup loop if we do not return immediately. This requires moving the reuseport_has_conns() logic into the callers. While we are here, get rid of inline directives as they do not belong in foo.c files. The other changes were cases of more straightforward overlapping modifications. Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: fec: fix hardware time stamping by external devicesSergey Organov2020-07-161-6/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix support for external PTP-aware devices such as DSA or PTP PHY: Make sure we never time stamp tx packets when hardware time stamping is disabled. Check for PTP PHY being in use and then pass ioctls related to time stamping of Ethernet packets to the PTP PHY rather than handle them ourselves. In addition, disable our own hardware time stamping in this case. Fixes: 6605b730c061 ("FEC: Add time stamping code and a PTP hardware clock") Signed-off-by: Sergey Organov <sorganov@gmail.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Acked-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
* | net: fec: Set max MTU size to allow the MTU to be changedAndrew Lunn2020-07-121-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The FEC allocates 2K buffers, but looses some of it due to alignment. It can however support an MTU bigger than the default. This is particularly interesting when used in combination with Ethernet switches supporting DSA, which have extra headers. The DSA core will try to increase the MTU to support these extra headers. If the max size defaults to that of standard Ethernet we get a warning. By setting the max to what the driver actually supports, we avoid this warning. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* | Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netDavid S. Miller2020-07-111-63/+31
|\| | | | | | | | | | | | | All conflicts seemed rather trivial, with some guidance from Saeed Mameed on the tc_ct.c one. Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: ethernet: fec: prevent tx starvation under high rx loadTobias Waldekranz2020-07-071-63/+31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In the ISR, we poll the event register for the queues in need of service and then enter polled mode. After this point, the event register will never be read again until we exit polled mode. In a scenario where a UDP flow is routed back out through the same interface, i.e. "router-on-a-stick" we'll typically only see an rx queue event initially. Once we start to process the incoming flow we'll be locked polled mode, but we'll never clean the tx rings since that event is never caught. Eventually the netdev watchdog will trip, causing all buffers to be dropped and then the process starts over again. Rework the NAPI poll to keep trying to consome the entire budget as long as new events are coming in, making sure to service all rx/tx queues, in priority order, on each pass. Fixes: 4d494cdc92b3 ("net: fec: change data structure to support multiqueue") Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com> Tested-by: Fugang Duan <fugang.duan@nxp.com> Reviewed-by: Fugang Duan <fugang.duan@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: tso: cache transport header lengthEric Dumazet2020-06-181-3/+2
|/ | | | | | | | | | | | | Add tlen field into struct tso_t, and change tso_start() to return skb_transport_offset(skb) + tso->tlen This removes from callers the need to use tcp_hdrlen(skb) and will ease UDP segmentation offload addition. v2: calls tso_start() earlier in otx2_sq_append_tso() [Jakub] Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: disable correct clk in the err path of fec_enet_clk_enableLiu Xiang2020-06-011-2/+6
| | | | | | | | When enable clk_ref failed, clk_ptp should be disabled rather than clk_ref itself. Signed-off-by: Liu Xiang <liuxiang_1999@126.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: ethernet: fec: move GPR register offset and bit into DTFugang Duan2020-05-261-12/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | The commit da722186f654 (net: fec: set GPR bit on suspend by DT configuration) set the GPR reigster offset and bit in driver for wake on lan feature. But it introduces two issues here: - one SOC has two instances, they have different bit - different SOCs may have different offset and bit So to support wake-on-lan feature on other i.MX platforms, it should configure the GPR reigster offset and bit from DT. So the patch is to improve the commit da722186f654 (net: fec: set GPR bit on suspend by DT configuration) to support multiple ethernet instances on i.MX series. v2: * switch back to store the quirks bitmask in driver_data v3: * suggested by Sascha Hauer, use a struct fec_devinfo for abstracting differences between different hardware variants, it can give more freedom to describe the differences. Signed-off-by: Fugang Duan <fugang.duan@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: ethernet: fec: Replace interrupt driven MDIO with polled IOAndrew Lunn2020-05-021-33/+44
| | | | | | | | | | | | | | | | | | | | | Measurements of the MDIO bus have shown that driving the MDIO bus using interrupts is slow. Back to back MDIO transactions take about 90us, with 25us spent performing the transaction, and the remainder of the time the bus is idle. Replacing the completion interrupt with polled IO results in back to back transactions of 40us. The polling loop waiting for the hardware to complete the transaction takes around 28us. Which suggests interrupt handling has an overhead of 50us, and polled IO nearly halves this overhead, and doubles the MDIO performance. Care has to be taken when setting the MII_SPEED register, or it can trigger an MII event> That then upsets the polling, due to an unexpected pending event. Suggested-by: Chris Heally <cphealy@gmail.com> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: ethernet: fec: Revert "net: ethernet: fec: Replace interrupt driven ↵Fugang Duan2020-04-301-34/+33
| | | | | | | | | | | | | MDIO with polled IO" This reverts commit 29ae6bd1b0d8a57d7c00ab12cbb949fc41986eef. The commit breaks ethernet function on i.MX6SX, i.MX7D, i.MX8MM, i.MX8MQ, and i.MX8QXP platforms. Boot yocto system by NFS mounting rootfs will be failed with the commit. Signed-off-by: Fugang Duan <fugang.duan@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Revert "net: ethernet: fec: Prevent MII event after MII_SPEED write"David S. Miller2020-04-291-17/+0
| | | | | | | | This reverts commit 790ab249b55d75fdb427b92f81964cd7cb525eec. This change needs more work. Signed-off-by: David S. Miller <davem@davemloft.net>
* net: ethernet: fec: Prevent MII event after MII_SPEED writeAndrew Lunn2020-04-281-0/+17
| | | | | | | | | | | | | | | | | | | | The change to polled IO for MDIO completion assumes that MII events are only generated for MDIO transactions. However on some SoCs writing to the MII_SPEED register can also trigger an MII event. As a result, the next MDIO read has a pending MII event, and immediately reads the data registers before it contains useful data. When the read does complete, another MII event is posted, which results in the next read also going wrong, and the cycle continues. By writing 0 to the MII_DATA register before writing to the speed register, this MII event for the MII_SPEED is suppressed, and polled IO works as expected. Fixes: 29ae6bd1b0d8 ("net: ethernet: fec: Replace interrupt driven MDIO with polled IO") Reported-by: Andy Duan <fugang.duan@nxp.com> Suggested-by: Andy Duan <fugang.duan@nxp.com> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: ethernet: fec: Allow the MDIO preamble to be disabledAndrew Lunn2020-04-201-1/+8
| | | | | | | | | | | | | An MDIO transaction normally starts with 32 1s as a preamble. However not all devices requires such a preamble. Add a device tree property which allows the preamble to be suppressed. This will half the size of the MDIO transaction, allowing faster transactions. But it should only be used when all devices on the bus support suppressed preamble. Suggested-by: Chris Healy <Chris.Healy@zii.aero> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: ethernet: fec: Allow configuration of MDIO bus speedAndrew Lunn2020-04-201-3/+8
| | | | | | | | | | | | | | | MDIO busses typically operate at 2.5MHz. However many devices can operate at faster speeds. This then allows more MDIO transactions per second, useful for Ethernet switch statistics, or Ethernet PHY TDR data. Allow the bus speed to be configured, using the standard "clock-frequency" property, which i2c busses use to indicate the bus speed. Before using this property, ensure all devices on the bus do actually support the requested clock speed. Suggested-by: Chris Healy <Chris.Healy@zii.aero> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: ethernet: fec: Replace interrupt driven MDIO with polled IOAndrew Lunn2020-04-201-33/+34
| | | | | | | | | | | | | | | | | Measurements of the MDIO bus have shown that driving the MDIO bus using interrupts is slow. Back to back MDIO transactions take about 90us, with 25us spent performing the transaction, and the remainder of the time the bus is idle. Replacing the completion interrupt with polled IO results in back to back transactions of 40us. The polling loop waiting for the hardware to complete the transaction takes around 28us. Which suggests interrupt handling has an overhead of 50us, and polled IO nearly halves this overhead, and doubles the MDIO performance. Suggested-by: Chris Heally <cphealy@gmail.com> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: set GPR bit on suspend by DT configuration.Martin Fuzzey2020-04-071-29/+120
| | | | | | | | | | | | | | | | | | | | | | On some SoCs, such as the i.MX6, it is necessary to set a bit in the SoC level GPR register before suspending for wake on lan to work. The fec platform callback sleep_mode_enable was intended to allow this but the platform implementation was NAK'd back in 2015 [1] This means that, currently, wake on lan is broken on mainline for the i.MX6 at least. So implement the required bit setting in the fec driver by itself by adding a new optional DT property indicating the GPR register and adding the offset and bit information to the driver. [1] https://www.spinics.net/lists/netdev/msg310922.html Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group> Signed-off-by: Fugang Duan <fugang.duan@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netDavid S. Miller2020-03-121-3/+3
|\ | | | | | | | | | | Minor overlapping changes, nothing serious. Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: fec: validate the new settings in fec_enet_set_coalesce()Jakub Kicinski2020-03-111-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | fec_enet_set_coalesce() validates the previously set params and if they are within range proceeds to apply the new ones. The new ones, however, are not validated. This seems backwards, probably a copy-paste error? Compile tested only. Fixes: d851b47b22fc ("net: fec: add interrupt coalescence feature support") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Acked-by: Fugang Duan <fugang.duan@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: fec: reject unsupported coalescing paramsJakub Kicinski2020-03-121-0/+2
| | | | | | | | | | | | | | | | | | | | | | Set ethtool_ops->supported_coalesce_params to let the core reject unsupported coalescing parameters. This driver did not previously reject unsupported parameters. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Acked-by: Fugang Duan <fugang.duan@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net/freescale: Clean drivers from static versionsLeon Romanovsky2020-03-031-1/+0
| | | | | | | | | | | | | | | | | | There is no need to set static versions because linux kernel is released all together with same version applicable to the whole code base. Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: fec: Prevent unbind operationFabio Estevam2020-02-181-0/+1
|/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | After performing an unbind/bind operation the network is no longer functional on i.MX6 (which has a single FEC instance): # echo 2188000.ethernet > /sys/bus/platform/drivers/fec/unbind # echo 2188000.ethernet > /sys/bus/platform/drivers/fec/bind [ 10.756519] pps pps0: new PPS source ptp0 [ 10.792626] libphy: fec_enet_mii_bus: probed [ 10.799330] fec 2188000.ethernet eth0: registered PHC device 1 # udhcpc -i eth0 udhcpc: started, v1.31.1 [ 14.985211] fec 2188000.ethernet eth0: no PHY, assuming direct connection to switch [ 14.993140] libphy: PHY fixed-0:00 not found [ 14.997643] fec 2188000.ethernet eth0: could not attach to PHY On SoCs with two FEC instances there are some cases where one FEC instance depends on the other one being present. One such example is i.MX28, which has the following FEC dependency as noted in the comments: /* * The i.MX28 dual fec interfaces are not equal. * Here are the differences: * * - fec0 supports MII & RMII modes while fec1 only supports RMII * - fec0 acts as the 1588 time master while fec1 is slave * - external phys can only be configured by fec0 * * That is to say fec1 can not work independently. It only works * when fec0 is working. The reason behind this design is that the * second interface is added primarily for Switch mode. * * Because of the last point above, both phys are attached on fec0 * mdio interface in board design, and need to be configured by * fec0 mii_bus. */ Prevent the unbind operation to avoid these issues. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netDavid S. Miller2020-01-091-0/+9
|\ | | | | | | | | | | | | | | The ungrafting from PRIO bug fixes in net, when merged into net-next, merge cleanly but create a build failure. The resolution used here is from Petr Machata. Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: freescale: fec: Fix ethtool -d runtime PMAndrew Lunn2020-01-021-0/+9
| | | | | | | | | | | | | | | | | | | | | | In order to dump the FECs registers the clocks have to be ticking, otherwise a data abort occurs. Add calls to runtime PM so they are enabled and later disabled. Fixes: e8fcfcd5684a ("net: fec: optimize the clock management to save power") Reported-by: Chris Healy <Chris.Healy@zii.aero> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* | netdev: pass the stuck queue to the timeout handlerMichael S. Tsirkin2019-12-121-1/+1
|/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This allows incrementing the correct timeout statistic without any mess. Down the road, devices can learn to reset just the specific queue. The patch was generated with the following script: use strict; use warnings; our $^I = '.bak'; my @work = ( ["arch/m68k/emu/nfeth.c", "nfeth_tx_timeout"], ["arch/um/drivers/net_kern.c", "uml_net_tx_timeout"], ["arch/um/drivers/vector_kern.c", "vector_net_tx_timeout"], ["arch/xtensa/platforms/iss/network.c", "iss_net_tx_timeout"], ["drivers/char/pcmcia/synclink_cs.c", "hdlcdev_tx_timeout"], ["drivers/infiniband/ulp/ipoib/ipoib_main.c", "ipoib_timeout"], ["drivers/infiniband/ulp/ipoib/ipoib_main.c", "ipoib_timeout"], ["drivers/message/fusion/mptlan.c", "mpt_lan_tx_timeout"], ["drivers/misc/sgi-xp/xpnet.c", "xpnet_dev_tx_timeout"], ["drivers/net/appletalk/cops.c", "cops_timeout"], ["drivers/net/arcnet/arcdevice.h", "arcnet_timeout"], ["drivers/net/arcnet/arcnet.c", "arcnet_timeout"], ["drivers/net/arcnet/com20020.c", "arcnet_timeout"], ["drivers/net/ethernet/3com/3c509.c", "el3_tx_timeout"], ["drivers/net/ethernet/3com/3c515.c", "corkscrew_timeout"], ["drivers/net/ethernet/3com/3c574_cs.c", "el3_tx_timeout"], ["drivers/net/ethernet/3com/3c589_cs.c", "el3_tx_timeout"], ["drivers/net/ethernet/3com/3c59x.c", "vortex_tx_timeout"], ["drivers/net/ethernet/3com/3c59x.c", "vortex_tx_timeout"], ["drivers/net/ethernet/3com/typhoon.c", "typhoon_tx_timeout"], ["drivers/net/ethernet/8390/8390.h", "ei_tx_timeout"], ["drivers/net/ethernet/8390/8390.h", "eip_tx_timeout"], ["drivers/net/ethernet/8390/8390.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/8390p.c", "eip_tx_timeout"], ["drivers/net/ethernet/8390/ax88796.c", "ax_ei_tx_timeout"], ["drivers/net/ethernet/8390/axnet_cs.c", "axnet_tx_timeout"], ["drivers/net/ethernet/8390/etherh.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/hydra.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/mac8390.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/mcf8390.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/lib8390.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/ne2k-pci.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/pcnet_cs.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/smc-ultra.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/wd.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/zorro8390.c", "__ei_tx_timeout"], ["drivers/net/ethernet/adaptec/starfire.c", "tx_timeout"], ["drivers/net/ethernet/agere/et131x.c", "et131x_tx_timeout"], ["drivers/net/ethernet/allwinner/sun4i-emac.c", "emac_timeout"], ["drivers/net/ethernet/alteon/acenic.c", "ace_watchdog"], ["drivers/net/ethernet/amazon/ena/ena_netdev.c", "ena_tx_timeout"], ["drivers/net/ethernet/amd/7990.h", "lance_tx_timeout"], ["drivers/net/ethernet/amd/7990.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/a2065.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/am79c961a.c", "am79c961_timeout"], ["drivers/net/ethernet/amd/amd8111e.c", "amd8111e_tx_timeout"], ["drivers/net/ethernet/amd/ariadne.c", "ariadne_tx_timeout"], ["drivers/net/ethernet/amd/atarilance.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/au1000_eth.c", "au1000_tx_timeout"], ["drivers/net/ethernet/amd/declance.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/lance.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/mvme147.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/ni65.c", "ni65_timeout"], ["drivers/net/ethernet/amd/nmclan_cs.c", "mace_tx_timeout"], ["drivers/net/ethernet/amd/pcnet32.c", "pcnet32_tx_timeout"], ["drivers/net/ethernet/amd/sunlance.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/xgbe/xgbe-drv.c", "xgbe_tx_timeout"], ["drivers/net/ethernet/apm/xgene-v2/main.c", "xge_timeout"], ["drivers/net/ethernet/apm/xgene/xgene_enet_main.c", "xgene_enet_timeout"], ["drivers/net/ethernet/apple/macmace.c", "mace_tx_timeout"], ["drivers/net/ethernet/atheros/ag71xx.c", "ag71xx_tx_timeout"], ["drivers/net/ethernet/atheros/alx/main.c", "alx_tx_timeout"], ["drivers/net/ethernet/atheros/atl1c/atl1c_main.c", "atl1c_tx_timeout"], ["drivers/net/ethernet/atheros/atl1e/atl1e_main.c", "atl1e_tx_timeout"], ["drivers/net/ethernet/atheros/atlx/atl.c", "atlx_tx_timeout"], ["drivers/net/ethernet/atheros/atlx/atl1.c", "atlx_tx_timeout"], ["drivers/net/ethernet/atheros/atlx/atl2.c", "atl2_tx_timeout"], ["drivers/net/ethernet/broadcom/b44.c", "b44_tx_timeout"], ["drivers/net/ethernet/broadcom/bcmsysport.c", "bcm_sysport_tx_timeout"], ["drivers/net/ethernet/broadcom/bnx2.c", "bnx2_tx_timeout"], ["drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h", "bnx2x_tx_timeout"], ["drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c", "bnx2x_tx_timeout"], ["drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c", "bnx2x_tx_timeout"], ["drivers/net/ethernet/broadcom/bnxt/bnxt.c", "bnxt_tx_timeout"], ["drivers/net/ethernet/broadcom/genet/bcmgenet.c", "bcmgenet_timeout"], ["drivers/net/ethernet/broadcom/sb1250-mac.c", "sbmac_tx_timeout"], ["drivers/net/ethernet/broadcom/tg3.c", "tg3_tx_timeout"], ["drivers/net/ethernet/calxeda/xgmac.c", "xgmac_tx_timeout"], ["drivers/net/ethernet/cavium/liquidio/lio_main.c", "liquidio_tx_timeout"], ["drivers/net/ethernet/cavium/liquidio/lio_vf_main.c", "liquidio_tx_timeout"], ["drivers/net/ethernet/cavium/liquidio/lio_vf_rep.c", "lio_vf_rep_tx_timeout"], ["drivers/net/ethernet/cavium/thunder/nicvf_main.c", "nicvf_tx_timeout"], ["drivers/net/ethernet/cirrus/cs89x0.c", "net_timeout"], ["drivers/net/ethernet/cisco/enic/enic_main.c", "enic_tx_timeout"], ["drivers/net/ethernet/cisco/enic/enic_main.c", "enic_tx_timeout"], ["drivers/net/ethernet/cortina/gemini.c", "gmac_tx_timeout"], ["drivers/net/ethernet/davicom/dm9000.c", "dm9000_timeout"], ["drivers/net/ethernet/dec/tulip/de2104x.c", "de_tx_timeout"], ["drivers/net/ethernet/dec/tulip/tulip_core.c", "tulip_tx_timeout"], ["drivers/net/ethernet/dec/tulip/winbond-840.c", "tx_timeout"], ["drivers/net/ethernet/dlink/dl2k.c", "rio_tx_timeout"], ["drivers/net/ethernet/dlink/sundance.c", "tx_timeout"], ["drivers/net/ethernet/emulex/benet/be_main.c", "be_tx_timeout"], ["drivers/net/ethernet/ethoc.c", "ethoc_tx_timeout"], ["drivers/net/ethernet/faraday/ftgmac100.c", "ftgmac100_tx_timeout"], ["drivers/net/ethernet/fealnx.c", "fealnx_tx_timeout"], ["drivers/net/ethernet/freescale/dpaa/dpaa_eth.c", "dpaa_tx_timeout"], ["drivers/net/ethernet/freescale/fec_main.c", "fec_timeout"], ["drivers/net/ethernet/freescale/fec_mpc52xx.c", "mpc52xx_fec_tx_timeout"], ["drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c", "fs_timeout"], ["drivers/net/ethernet/freescale/gianfar.c", "gfar_timeout"], ["drivers/net/ethernet/freescale/ucc_geth.c", "ucc_geth_timeout"], ["drivers/net/ethernet/fujitsu/fmvj18x_cs.c", "fjn_tx_timeout"], ["drivers/net/ethernet/google/gve/gve_main.c", "gve_tx_timeout"], ["drivers/net/ethernet/hisilicon/hip04_eth.c", "hip04_timeout"], ["drivers/net/ethernet/hisilicon/hix5hd2_gmac.c", "hix5hd2_net_timeout"], ["drivers/net/ethernet/hisilicon/hns/hns_enet.c", "hns_nic_net_timeout"], ["drivers/net/ethernet/hisilicon/hns3/hns3_enet.c", "hns3_nic_net_timeout"], ["drivers/net/ethernet/huawei/hinic/hinic_main.c", "hinic_tx_timeout"], ["drivers/net/ethernet/i825xx/82596.c", "i596_tx_timeout"], ["drivers/net/ethernet/i825xx/ether1.c", "ether1_timeout"], ["drivers/net/ethernet/i825xx/lib82596.c", "i596_tx_timeout"], ["drivers/net/ethernet/i825xx/sun3_82586.c", "sun3_82586_timeout"], ["drivers/net/ethernet/ibm/ehea/ehea_main.c", "ehea_tx_watchdog"], ["drivers/net/ethernet/ibm/emac/core.c", "emac_tx_timeout"], ["drivers/net/ethernet/ibm/emac/core.c", "emac_tx_timeout"], ["drivers/net/ethernet/ibm/ibmvnic.c", "ibmvnic_tx_timeout"], ["drivers/net/ethernet/intel/e100.c", "e100_tx_timeout"], ["drivers/net/ethernet/intel/e1000/e1000_main.c", "e1000_tx_timeout"], ["drivers/net/ethernet/intel/e1000e/netdev.c", "e1000_tx_timeout"], ["drivers/net/ethernet/intel/fm10k/fm10k_netdev.c", "fm10k_tx_timeout"], ["drivers/net/ethernet/intel/i40e/i40e_main.c", "i40e_tx_timeout"], ["drivers/net/ethernet/intel/iavf/iavf_main.c", "iavf_tx_timeout"], ["drivers/net/ethernet/intel/ice/ice_main.c", "ice_tx_timeout"], ["drivers/net/ethernet/intel/ice/ice_main.c", "ice_tx_timeout"], ["drivers/net/ethernet/intel/igb/igb_main.c", "igb_tx_timeout"], ["drivers/net/ethernet/intel/igbvf/netdev.c", "igbvf_tx_timeout"], ["drivers/net/ethernet/intel/ixgb/ixgb_main.c", "ixgb_tx_timeout"], ["drivers/net/ethernet/intel/ixgbe/ixgbe_debugfs.c", "adapter->netdev->netdev_ops->ndo_tx_timeout(adapter->netdev);"], ["drivers/net/ethernet/intel/ixgbe/ixgbe_main.c", "ixgbe_tx_timeout"], ["drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c", "ixgbevf_tx_timeout"], ["drivers/net/ethernet/jme.c", "jme_tx_timeout"], ["drivers/net/ethernet/korina.c", "korina_tx_timeout"], ["drivers/net/ethernet/lantiq_etop.c", "ltq_etop_tx_timeout"], ["drivers/net/ethernet/marvell/mv643xx_eth.c", "mv643xx_eth_tx_timeout"], ["drivers/net/ethernet/marvell/pxa168_eth.c", "pxa168_eth_tx_timeout"], ["drivers/net/ethernet/marvell/skge.c", "skge_tx_timeout"], ["drivers/net/ethernet/marvell/sky2.c", "sky2_tx_timeout"], ["drivers/net/ethernet/marvell/sky2.c", "sky2_tx_timeout"], ["drivers/net/ethernet/mediatek/mtk_eth_soc.c", "mtk_tx_timeout"], ["drivers/net/ethernet/mellanox/mlx4/en_netdev.c", "mlx4_en_tx_timeout"], ["drivers/net/ethernet/mellanox/mlx4/en_netdev.c", "mlx4_en_tx_timeout"], ["drivers/net/ethernet/mellanox/mlx5/core/en_main.c", "mlx5e_tx_timeout"], ["drivers/net/ethernet/micrel/ks8842.c", "ks8842_tx_timeout"], ["drivers/net/ethernet/micrel/ksz884x.c", "netdev_tx_timeout"], ["drivers/net/ethernet/microchip/enc28j60.c", "enc28j60_tx_timeout"], ["drivers/net/ethernet/microchip/encx24j600.c", "encx24j600_tx_timeout"], ["drivers/net/ethernet/natsemi/sonic.h", "sonic_tx_timeout"], ["drivers/net/ethernet/natsemi/sonic.c", "sonic_tx_timeout"], ["drivers/net/ethernet/natsemi/jazzsonic.c", "sonic_tx_timeout"], ["drivers/net/ethernet/natsemi/macsonic.c", "sonic_tx_timeout"], ["drivers/net/ethernet/natsemi/natsemi.c", "ns_tx_timeout"], ["drivers/net/ethernet/natsemi/ns83820.c", "ns83820_tx_timeout"], ["drivers/net/ethernet/natsemi/xtsonic.c", "sonic_tx_timeout"], ["drivers/net/ethernet/neterion/s2io.h", "s2io_tx_watchdog"], ["drivers/net/ethernet/neterion/s2io.c", "s2io_tx_watchdog"], ["drivers/net/ethernet/neterion/vxge/vxge-main.c", "vxge_tx_watchdog"], ["drivers/net/ethernet/netronome/nfp/nfp_net_common.c", "nfp_net_tx_timeout"], ["drivers/net/ethernet/nvidia/forcedeth.c", "nv_tx_timeout"], ["drivers/net/ethernet/nvidia/forcedeth.c", "nv_tx_timeout"], ["drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.c", "pch_gbe_tx_timeout"], ["drivers/net/ethernet/packetengines/hamachi.c", "hamachi_tx_timeout"], ["drivers/net/ethernet/packetengines/yellowfin.c", "yellowfin_tx_timeout"], ["drivers/net/ethernet/pensando/ionic/ionic_lif.c", "ionic_tx_timeout"], ["drivers/net/ethernet/qlogic/netxen/netxen_nic_main.c", "netxen_tx_timeout"], ["drivers/net/ethernet/qlogic/qla3xxx.c", "ql3xxx_tx_timeout"], ["drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c", "qlcnic_tx_timeout"], ["drivers/net/ethernet/qualcomm/emac/emac.c", "emac_tx_timeout"], ["drivers/net/ethernet/qualcomm/qca_spi.c", "qcaspi_netdev_tx_timeout"], ["drivers/net/ethernet/qualcomm/qca_uart.c", "qcauart_netdev_tx_timeout"], ["drivers/net/ethernet/rdc/r6040.c", "r6040_tx_timeout"], ["drivers/net/ethernet/realtek/8139cp.c", "cp_tx_timeout"], ["drivers/net/ethernet/realtek/8139too.c", "rtl8139_tx_timeout"], ["drivers/net/ethernet/realtek/atp.c", "tx_timeout"], ["drivers/net/ethernet/realtek/r8169_main.c", "rtl8169_tx_timeout"], ["drivers/net/ethernet/renesas/ravb_main.c", "ravb_tx_timeout"], ["drivers/net/ethernet/renesas/sh_eth.c", "sh_eth_tx_timeout"], ["drivers/net/ethernet/renesas/sh_eth.c", "sh_eth_tx_timeout"], ["drivers/net/ethernet/samsung/sxgbe/sxgbe_main.c", "sxgbe_tx_timeout"], ["drivers/net/ethernet/seeq/ether3.c", "ether3_timeout"], ["drivers/net/ethernet/seeq/sgiseeq.c", "timeout"], ["drivers/net/ethernet/sfc/efx.c", "efx_watchdog"], ["drivers/net/ethernet/sfc/falcon/efx.c", "ef4_watchdog"], ["drivers/net/ethernet/sgi/ioc3-eth.c", "ioc3_timeout"], ["drivers/net/ethernet/sgi/meth.c", "meth_tx_timeout"], ["drivers/net/ethernet/silan/sc92031.c", "sc92031_tx_timeout"], ["drivers/net/ethernet/sis/sis190.c", "sis190_tx_timeout"], ["drivers/net/ethernet/sis/sis900.c", "sis900_tx_timeout"], ["drivers/net/ethernet/smsc/epic100.c", "epic_tx_timeout"], ["drivers/net/ethernet/smsc/smc911x.c", "smc911x_timeout"], ["drivers/net/ethernet/smsc/smc9194.c", "smc_timeout"], ["drivers/net/ethernet/smsc/smc91c92_cs.c", "smc_tx_timeout"], ["drivers/net/ethernet/smsc/smc91x.c", "smc_timeout"], ["drivers/net/ethernet/stmicro/stmmac/stmmac_main.c", "stmmac_tx_timeout"], ["drivers/net/ethernet/sun/cassini.c", "cas_tx_timeout"], ["drivers/net/ethernet/sun/ldmvsw.c", "sunvnet_tx_timeout_common"], ["drivers/net/ethernet/sun/niu.c", "niu_tx_timeout"], ["drivers/net/ethernet/sun/sunbmac.c", "bigmac_tx_timeout"], ["drivers/net/ethernet/sun/sungem.c", "gem_tx_timeout"], ["drivers/net/ethernet/sun/sunhme.c", "happy_meal_tx_timeout"], ["drivers/net/ethernet/sun/sunqe.c", "qe_tx_timeout"], ["drivers/net/ethernet/sun/sunvnet.c", "sunvnet_tx_timeout_common"], ["drivers/net/ethernet/sun/sunvnet_common.c", "sunvnet_tx_timeout_common"], ["drivers/net/ethernet/sun/sunvnet_common.h", "sunvnet_tx_timeout_common"], ["drivers/net/ethernet/synopsys/dwc-xlgmac-net.c", "xlgmac_tx_timeout"], ["drivers/net/ethernet/ti/cpmac.c", "cpmac_tx_timeout"], ["drivers/net/ethernet/ti/cpsw.c", "cpsw_ndo_tx_timeout"], ["drivers/net/ethernet/ti/cpsw_priv.c", "cpsw_ndo_tx_timeout"], ["drivers/net/ethernet/ti/cpsw_priv.h", "cpsw_ndo_tx_timeout"], ["drivers/net/ethernet/ti/davinci_emac.c", "emac_dev_tx_timeout"], ["drivers/net/ethernet/ti/netcp_core.c", "netcp_ndo_tx_timeout"], ["drivers/net/ethernet/ti/tlan.c", "tlan_tx_timeout"], ["drivers/net/ethernet/toshiba/ps3_gelic_net.h", "gelic_net_tx_timeout"], ["drivers/net/ethernet/toshiba/ps3_gelic_net.c", "gelic_net_tx_timeout"], ["drivers/net/ethernet/toshiba/ps3_gelic_wireless.c", "gelic_net_tx_timeout"], ["drivers/net/ethernet/toshiba/spider_net.c", "spider_net_tx_timeout"], ["drivers/net/ethernet/toshiba/tc35815.c", "tc35815_tx_timeout"], ["drivers/net/ethernet/via/via-rhine.c", "rhine_tx_timeout"], ["drivers/net/ethernet/wiznet/w5100.c", "w5100_tx_timeout"], ["drivers/net/ethernet/wiznet/w5300.c", "w5300_tx_timeout"], ["drivers/net/ethernet/xilinx/xilinx_emaclite.c", "xemaclite_tx_timeout"], ["drivers/net/ethernet/xircom/xirc2ps_cs.c", "xirc_tx_timeout"], ["drivers/net/fjes/fjes_main.c", "fjes_tx_retry"], ["drivers/net/slip/slip.c", "sl_tx_timeout"], ["include/linux/usb/usbnet.h", "usbnet_tx_timeout"], ["drivers/net/usb/aqc111.c", "usbnet_tx_timeout"], ["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"], ["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"], ["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"], ["drivers/net/usb/ax88172a.c", "usbnet_tx_timeout"], ["drivers/net/usb/ax88179_178a.c", "usbnet_tx_timeout"], ["drivers/net/usb/catc.c", "catc_tx_timeout"], ["drivers/net/usb/cdc_mbim.c", "usbnet_tx_timeout"], ["drivers/net/usb/cdc_ncm.c", "usbnet_tx_timeout"], ["drivers/net/usb/dm9601.c", "usbnet_tx_timeout"], ["drivers/net/usb/hso.c", "hso_net_tx_timeout"], ["drivers/net/usb/int51x1.c", "usbnet_tx_timeout"], ["drivers/net/usb/ipheth.c", "ipheth_tx_timeout"], ["drivers/net/usb/kaweth.c", "kaweth_tx_timeout"], ["drivers/net/usb/lan78xx.c", "lan78xx_tx_timeout"], ["drivers/net/usb/mcs7830.c", "usbnet_tx_timeout"], ["drivers/net/usb/pegasus.c", "pegasus_tx_timeout"], ["drivers/net/usb/qmi_wwan.c", "usbnet_tx_timeout"], ["drivers/net/usb/r8152.c", "rtl8152_tx_timeout"], ["drivers/net/usb/rndis_host.c", "usbnet_tx_timeout"], ["drivers/net/usb/rtl8150.c", "rtl8150_tx_timeout"], ["drivers/net/usb/sierra_net.c", "usbnet_tx_timeout"], ["drivers/net/usb/smsc75xx.c", "usbnet_tx_timeout"], ["drivers/net/usb/smsc95xx.c", "usbnet_tx_timeout"], ["drivers/net/usb/sr9700.c", "usbnet_tx_timeout"], ["drivers/net/usb/sr9800.c", "usbnet_tx_timeout"], ["drivers/net/usb/usbnet.c", "usbnet_tx_timeout"], ["drivers/net/vmxnet3/vmxnet3_drv.c", "vmxnet3_tx_timeout"], ["drivers/net/wan/cosa.c", "cosa_net_timeout"], ["drivers/net/wan/farsync.c", "fst_tx_timeout"], ["drivers/net/wan/fsl_ucc_hdlc.c", "uhdlc_tx_timeout"], ["drivers/net/wan/lmc/lmc_main.c", "lmc_driver_timeout"], ["drivers/net/wan/x25_asy.c", "x25_asy_timeout"], ["drivers/net/wimax/i2400m/netdev.c", "i2400m_tx_timeout"], ["drivers/net/wireless/intel/ipw2x00/ipw2100.c", "ipw2100_tx_timeout"], ["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"], ["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"], ["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"], ["drivers/net/wireless/intersil/orinoco/main.c", "orinoco_tx_timeout"], ["drivers/net/wireless/intersil/orinoco/orinoco_usb.c", "orinoco_tx_timeout"], ["drivers/net/wireless/intersil/orinoco/orinoco.h", "orinoco_tx_timeout"], ["drivers/net/wireless/intersil/prism54/islpci_dev.c", "islpci_eth_tx_timeout"], ["drivers/net/wireless/intersil/prism54/islpci_eth.c", "islpci_eth_tx_timeout"], ["drivers/net/wireless/intersil/prism54/islpci_eth.h", "islpci_eth_tx_timeout"], ["drivers/net/wireless/marvell/mwifiex/main.c", "mwifiex_tx_timeout"], ["drivers/net/wireless/quantenna/qtnfmac/core.c", "qtnf_netdev_tx_timeout"], ["drivers/net/wireless/quantenna/qtnfmac/core.h", "qtnf_netdev_tx_timeout"], ["drivers/net/wireless/rndis_wlan.c", "usbnet_tx_timeout"], ["drivers/net/wireless/wl3501_cs.c", "wl3501_tx_timeout"], ["drivers/net/wireless/zydas/zd1201.c", "zd1201_tx_timeout"], ["drivers/s390/net/qeth_core.h", "qeth_tx_timeout"], ["drivers/s390/net/qeth_core_main.c", "qeth_tx_timeout"], ["drivers/s390/net/qeth_l2_main.c", "qeth_tx_timeout"], ["drivers/s390/net/qeth_l2_main.c", "qeth_tx_timeout"], ["drivers/s390/net/qeth_l3_main.c", "qeth_tx_timeout"], ["drivers/s390/net/qeth_l3_main.c", "qeth_tx_timeout"], ["drivers/staging/ks7010/ks_wlan_net.c", "ks_wlan_tx_timeout"], ["drivers/staging/qlge/qlge_main.c", "qlge_tx_timeout"], ["drivers/staging/rtl8192e/rtl8192e/rtl_core.c", "_rtl92e_tx_timeout"], ["drivers/staging/rtl8192u/r8192U_core.c", "tx_timeout"], ["drivers/staging/unisys/visornic/visornic_main.c", "visornic_xmit_timeout"], ["drivers/staging/wlan-ng/p80211netdev.c", "p80211knetdev_tx_timeout"], ["drivers/tty/n_gsm.c", "gsm_mux_net_tx_timeout"], ["drivers/tty/synclink.c", "hdlcdev_tx_timeout"], ["drivers/tty/synclink_gt.c", "hdlcdev_tx_timeout"], ["drivers/tty/synclinkmp.c", "hdlcdev_tx_timeout"], ["net/atm/lec.c", "lec_tx_timeout"], ["net/bluetooth/bnep/netdev.c", "bnep_net_timeout"] ); for my $p (@work) { my @pair = @$p; my $file = $pair[0]; my $func = $pair[1]; print STDERR $file , ": ", $func,"\n"; our @ARGV = ($file); while (<ARGV>) { if (m/($func\s*\(struct\s+net_device\s+\*[A-Za-z_]?[A-Za-z-0-9_]*)(\))/) { print STDERR "found $1+$2 in $file\n"; } if (s/($func\s*\(struct\s+net_device\s+\*[A-Za-z_]?[A-Za-z-0-9_]*)(\))/$1, unsigned int txqueue$2/) { print STDERR "$func found in $file\n"; } print; } } where the list of files and functions is simply from: git grep ndo_tx_timeout, with manual addition of headers in the rare cases where the function is from a header, then manually changing the few places which actually call ndo_tx_timeout. Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Heiner Kallweit <hkallweit1@gmail.com> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Shannon Nelson <snelson@pensando.io> Reviewed-by: Martin Habets <mhabets@solarflare.com> changes from v9: fixup a forward declaration changes from v9: more leftovers from v3 change changes from v8: fix up a missing direct call to timeout rebased on net-next changes from v7: fixup leftovers from v3 change changes from v6: fix typo in rtl driver changes from v5: add missing files (allow any net device argument name) changes from v4: add a missing driver header changes from v3: change queue # to unsigned Changes from v2: added headers Changes from v1: Fix errors found by kbuild: generalize the pattern a bit, to pick up a couple of instances missed by the previous version. Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski2019-11-221-4/+11
|\ | | | | | | | | | | | | | | | | Minor conflict in drivers/s390/net/qeth_l2_main.c, kept the lock from commit c8183f548902 ("s390/qeth: fix potential deadlock on workqueue flush"), removed the code which was removed by commit 9897d583b015 ("s390/qeth: consolidate some duplicated HW cmd code"). Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
| * net: fec: fix clock count mis-matchChuhong Yuan2019-11-191-4/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | pm_runtime_put_autosuspend in probe will call runtime suspend to disable clks automatically if CONFIG_PM is defined. (If CONFIG_PM is not defined, its implementation will be empty, then runtime suspend will not be called.) Therefore, we can call pm_runtime_get_sync to runtime resume it first to enable clks, which matches the runtime suspend. (Only when CONFIG_PM is defined, otherwise pm_runtime_get_sync will also be empty, then runtime resume will not be called.) Then it is fine to disable clks without causing clock count mis-match. Fixes: c43eab3eddb4 ("net: fec: add missed clk_disable_unprepare in remove") Signed-off-by: Chuhong Yuan <hslester96@gmail.com> Acked-by: Fugang Duan <fugang.duan@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netDavid S. Miller2019-11-091-0/+2
|\| | | | | | | | | | | | | One conflict in the BPF samples Makefile, some fixes in 'net' whilst we were converting over to Makefile.target rules in 'net-next'. Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: fec: add missed clk_disable_unprepare in removeChuhong Yuan2019-11-041-0/+2
| | | | | | | | | | | | | | | | This driver forgets to disable and unprepare clks when remove. Add calls to clk_disable_unprepare to fix it. Signed-off-by: Chuhong Yuan <hslester96@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: of_get_phy_mode: Change API to solve int/unit warningsAndrew Lunn2019-11-041-3/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Before this change of_get_phy_mode() returned an enum, phy_interface_t. On error, -ENODEV etc, is returned. If the result of the function is stored in a variable of type phy_interface_t, and the compiler has decided to represent this as an unsigned int, comparision with -ENODEV etc, is a signed vs unsigned comparision. Fix this problem by changing the API. Make the function return an error, or 0 on success, and pass a pointer, of type phy_interface_t, where the phy mode should be stored. v2: Return with *interface set to PHY_INTERFACE_MODE_NA on error. Add error checks to all users of of_get_phy_mode() Fixup a few reverse christmas tree errors Fixup a few slightly malformed reverse christmas trees v3: Fix 0-day reported errors. Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* | Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netDavid S. Miller2019-11-021-1/+1
|\| | | | | | | | | | | | | | | | | The only slightly tricky merge conflict was the netdevsim because the mutex locking fix overlapped a lot of driver reload reorganization. The rest were (relatively) trivial in nature. Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: fec_main: Use platform_get_irq_byname_optional() to avoid error messageAnson Huang2019-10-291-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Failed to get irq using name is NOT fatal as driver will use index to get irq instead, use platform_get_irq_byname_optional() instead of platform_get_irq_byname() to avoid below error message during probe: [ 0.819312] fec 30be0000.ethernet: IRQ int0 not found [ 0.824433] fec 30be0000.ethernet: IRQ int1 not found [ 0.829539] fec 30be0000.ethernet: IRQ int2 not found Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Acked-by: Fugang Duan <fugang.duan@nxp.com> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: fec: remove redundant assignment to pointer bdpColin Ian King2019-10-291-1/+0
|/ | | | | | | | | | The pointer bdp is being assigned with a value that is never read, so the assignment is redundant and hence can be removed. Addresses-Coverity: ("Unused value") Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Fugang Duan <fugang.duan@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: add C45 MDIO read/write supportMarco Hartmann2019-08-221-6/+64
| | | | | | | | | | | | | IEEE 802.3ae clause 45 defines a modified MDIO protocol that uses a two staged access model in order to increase the address space. This patch adds support for C45 MDIO read and write accesses, which are used whenever the MII_ADDR_C45 flag in the regnum argument is set. In case it is not set, C22 accesses are used as before. Signed-off-by: Marco Hartmann <marco.hartmann@nxp.com> Acked-by: Fugang Duan <fugang.duan@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: use devm_platform_ioremap_resource() to simplify codeYueHaibing2019-08-211-3/+1
| | | | | | | | | Use devm_platform_ioremap_resource() to simplify the code a bit. This is detected by coccinelle. Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: Use skb accessors in network driversMatthew Wilcox (Oracle)2019-07-221-2/+2
| | | | | | | | | In preparation for unifying the skb_frag and bio_vec, use the fine accessors which already exist and use skb_frag_t instead of struct skb_frag_struct. Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* ethernet: remove redundant memsetFuqian Huang2019-07-151-2/+0
| | | | | | | | | | | | kvzalloc already zeroes the memory during the allocation. pci_alloc_consistent calls dma_alloc_coherent directly. In commit 518a2f1925c3 ("dma-mapping: zero memory returned from dma_alloc_*"), dma_alloc_coherent has already zeroed the memory. So the memset after these function is not needed. Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec_main: Use dev_err() instead of pr_err()Fabio Estevam2019-06-091-4/+5
| | | | | | | | dev_err() is more appropriate for printing error messages inside drivers, so switch to dev_err(). Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: fec: Do not use netdev messages too earlyFabio Estevam2019-06-061-3/+3
| | | | | | | | | | | | | | | | | | | | When a valid MAC address is not found the current messages are shown: fec 2188000.ethernet (unnamed net_device) (uninitialized): Invalid MAC address: 00:00:00:00:00:00 fec 2188000.ethernet (unnamed net_device) (uninitialized): Using random MAC address: aa:9f:25:eb:7e:aa Since the network device has not been registered at this point, it is better to use dev_err()/dev_info() instead, which will provide cleaner log messages like these: fec 2188000.ethernet: Invalid MAC address: 00:00:00:00:00:00 fec 2188000.ethernet: Using random MAC address: aa:9f:25:eb:7e:aa Tested on a imx6dl-pico-pi board. Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2019-05-311-1/+1
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | The phylink conflict was between a bug fix by Russell King to make sure we have a consistent PHY interface mode, and a change in net-next to pull some code in phylink_resolve() into the helper functions phylink_mac_link_{up,down}() On the dp83867 side it's mostly overlapping changes, with the 'net' side removing a condition that was supposed to trigger for RGMII but because of how it was coded never actually could trigger. Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: fec: fix the clk mismatch in failed_reset pathAndy Duan2019-05-241-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | Fix the clk mismatch in the error path "failed_reset" because below error path will disable clk_ahb and clk_ipg directly, it should use pm_runtime_put_noidle() instead of pm_runtime_put() to avoid to call runtime resume callback. Reported-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Fugang Duan <fugang.duan@nxp.com> Tested-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: fec: remove redundant ipg clock disableBaruch Siach2019-05-221-1/+0
|/ | | | | | | | Don't disable the ipg clock in the regulator error path. The clock is disable unconditionally two lines below the failed_regulator label. Signed-off-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit (git 2.34.1) at 2025-02-28 16:10:51 +0000