aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net/wireless/ath/ath9k
Commit message (Collapse)AuthorAgeFilesLines
...
* ath9k: fix AR9002 ADC and NF calibrationsSergey Ryazanov2020-04-281-3/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | ADC calibration is only required for a 80 MHz sampling rate (i.e. for 40 MHz channels), when the chip utilizes the pair of ADCs in interleved mode. Calibration on a 20 MHz channel will never be completed. Previous channel check is trying to exclude all channels where the calibration will get stuck. It effectively blocks the calibration run for HT20 channels, but fails to exclude 20 MHz channels without HT (e.g. legacy mode channels). Fix this issue by reworking the channel check to explicitly allow ADCs gain & DC offset calibrations for HT40 channels only. Also update the complicated comment to make it clear that these calibrations are for multi-ADC mode only. Stuck ADCs calibration blocks the NF calibration, what could make it impossible to work in a noisy evironment: too big Rx attentuation, invalid RSSI value, etc. So this change is actually more of a NF calibration fix rather then the ADC calibration fix. Run tested with AR9220. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200424004923.17129-2-ryazanov.s.a@gmail.com
* ath9k: Fix general protection fault in ath9k_hif_usb_rx_cbQiujun Huang2020-04-072-11/+42
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In ath9k_hif_usb_rx_cb interface number is assumed to be 0. usb_ifnum_to_if(urb->dev, 0) But it isn't always true. The case reported by syzbot: https://lore.kernel.org/linux-usb/000000000000666c9c05a1c05d12@google.com usb 2-1: new high-speed USB device number 2 using dummy_hcd usb 2-1: config 1 has an invalid interface number: 2 but max is 0 usb 2-1: config 1 has no interface number 0 usb 2-1: New USB device found, idVendor=0cf3, idProduct=9271, bcdDevice= 1.08 usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 general protection fault, probably for non-canonical address 0xdffffc0000000015: 0000 [#1] SMP KASAN KASAN: null-ptr-deref in range [0x00000000000000a8-0x00000000000000af] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.6.0-rc5-syzkaller #0 Call Trace __usb_hcd_giveback_urb+0x29a/0x550 drivers/usb/core/hcd.c:1650 usb_hcd_giveback_urb+0x368/0x420 drivers/usb/core/hcd.c:1716 dummy_timer+0x1258/0x32ae drivers/usb/gadget/udc/dummy_hcd.c:1966 call_timer_fn+0x195/0x6f0 kernel/time/timer.c:1404 expire_timers kernel/time/timer.c:1449 [inline] __run_timers kernel/time/timer.c:1773 [inline] __run_timers kernel/time/timer.c:1740 [inline] run_timer_softirq+0x5f9/0x1500 kernel/time/timer.c:1786 __do_softirq+0x21e/0x950 kernel/softirq.c:292 invoke_softirq kernel/softirq.c:373 [inline] irq_exit+0x178/0x1a0 kernel/softirq.c:413 exiting_irq arch/x86/include/asm/apic.h:546 [inline] smp_apic_timer_interrupt+0x141/0x540 arch/x86/kernel/apic/apic.c:1146 apic_timer_interrupt+0xf/0x20 arch/x86/entry/entry_64.S:829 Reported-and-tested-by: syzbot+40d5d2e8a4680952f042@syzkaller.appspotmail.com Signed-off-by: Qiujun Huang <hqjagain@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200404041838.10426-6-hqjagain@gmail.com
* ath9x: Fix stack-out-of-bounds Write in ath9k_hif_usb_rx_cbQiujun Huang2020-04-071-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add barrier to accessing the stack array skb_pool. The case reported by syzbot: https://lore.kernel.org/linux-usb/0000000000003d7c1505a2168418@google.com BUG: KASAN: stack-out-of-bounds in ath9k_hif_usb_rx_stream drivers/net/wireless/ath/ath9k/hif_usb.c:626 [inline] BUG: KASAN: stack-out-of-bounds in ath9k_hif_usb_rx_cb+0xdf6/0xf70 drivers/net/wireless/ath/ath9k/hif_usb.c:666 Write of size 8 at addr ffff8881db309a28 by task swapper/1/0 Call Trace: ath9k_hif_usb_rx_stream drivers/net/wireless/ath/ath9k/hif_usb.c:626 [inline] ath9k_hif_usb_rx_cb+0xdf6/0xf70 drivers/net/wireless/ath/ath9k/hif_usb.c:666 __usb_hcd_giveback_urb+0x1f2/0x470 drivers/usb/core/hcd.c:1648 usb_hcd_giveback_urb+0x368/0x420 drivers/usb/core/hcd.c:1713 dummy_timer+0x1258/0x32ae drivers/usb/gadget/udc/dummy_hcd.c:1966 call_timer_fn+0x195/0x6f0 kernel/time/timer.c:1404 expire_timers kernel/time/timer.c:1449 [inline] __run_timers kernel/time/timer.c:1773 [inline] __run_timers kernel/time/timer.c:1740 [inline] run_timer_softirq+0x5f9/0x1500 kernel/time/timer.c:1786 Reported-and-tested-by: syzbot+d403396d4df67ad0bd5f@syzkaller.appspotmail.com Signed-off-by: Qiujun Huang <hqjagain@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200404041838.10426-5-hqjagain@gmail.com
* ath9k: Fix use-after-free Write in ath9k_htc_rx_msgQiujun Huang2020-04-071-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Write out of slab bounds. We should check epid. The case reported by syzbot: https://lore.kernel.org/linux-usb/0000000000006ac55b05a1c05d72@google.com BUG: KASAN: use-after-free in htc_process_conn_rsp drivers/net/wireless/ath/ath9k/htc_hst.c:131 [inline] BUG: KASAN: use-after-free in ath9k_htc_rx_msg+0xa25/0xaf0 drivers/net/wireless/ath/ath9k/htc_hst.c:443 Write of size 2 at addr ffff8881cea291f0 by task swapper/1/0 Call Trace: htc_process_conn_rsp drivers/net/wireless/ath/ath9k/htc_hst.c:131 [inline] ath9k_htc_rx_msg+0xa25/0xaf0 drivers/net/wireless/ath/ath9k/htc_hst.c:443 ath9k_hif_usb_reg_in_cb+0x1ba/0x630 drivers/net/wireless/ath/ath9k/hif_usb.c:718 __usb_hcd_giveback_urb+0x29a/0x550 drivers/usb/core/hcd.c:1650 usb_hcd_giveback_urb+0x368/0x420 drivers/usb/core/hcd.c:1716 dummy_timer+0x1258/0x32ae drivers/usb/gadget/udc/dummy_hcd.c:1966 call_timer_fn+0x195/0x6f0 kernel/time/timer.c:1404 expire_timers kernel/time/timer.c:1449 [inline] __run_timers kernel/time/timer.c:1773 [inline] __run_timers kernel/time/timer.c:1740 [inline] run_timer_softirq+0x5f9/0x1500 kernel/time/timer.c:1786 Reported-and-tested-by: syzbot+b1c61e5f11be5782f192@syzkaller.appspotmail.com Signed-off-by: Qiujun Huang <hqjagain@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200404041838.10426-4-hqjagain@gmail.com
* ath9k: Fix use-after-free Read in ath9k_wmi_ctrl_rxQiujun Huang2020-04-075-7/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Free wmi later after cmd urb has been killed, as urb cb will access wmi. the case reported by syzbot: https://lore.kernel.org/linux-usb/0000000000000002fc05a1d61a68@google.com BUG: KASAN: use-after-free in ath9k_wmi_ctrl_rx+0x416/0x500 drivers/net/wireless/ath/ath9k/wmi.c:215 Read of size 1 at addr ffff8881cef1417c by task swapper/1/0 Call Trace: <IRQ> ath9k_wmi_ctrl_rx+0x416/0x500 drivers/net/wireless/ath/ath9k/wmi.c:215 ath9k_htc_rx_msg+0x2da/0xaf0 drivers/net/wireless/ath/ath9k/htc_hst.c:459 ath9k_hif_usb_reg_in_cb+0x1ba/0x630 drivers/net/wireless/ath/ath9k/hif_usb.c:718 __usb_hcd_giveback_urb+0x29a/0x550 drivers/usb/core/hcd.c:1650 usb_hcd_giveback_urb+0x368/0x420 drivers/usb/core/hcd.c:1716 dummy_timer+0x1258/0x32ae drivers/usb/gadget/udc/dummy_hcd.c:1966 call_timer_fn+0x195/0x6f0 kernel/time/timer.c:1404 expire_timers kernel/time/timer.c:1449 [inline] __run_timers kernel/time/timer.c:1773 [inline] __run_timers kernel/time/timer.c:1740 [inline] run_timer_softirq+0x5f9/0x1500 kernel/time/timer.c:1786 Reported-and-tested-by: syzbot+5d338854440137ea0fef@syzkaller.appspotmail.com Signed-off-by: Qiujun Huang <hqjagain@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200404041838.10426-3-hqjagain@gmail.com
* ath9k: Fix use-after-free Read in htc_connect_serviceQiujun Huang2020-04-072-4/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The skb is consumed by htc_send_epid, so it needn't release again. The case reported by syzbot: https://lore.kernel.org/linux-usb/000000000000590f6b05a1c05d15@google.com usb 1-1: ath9k_htc: Firmware ath9k_htc/htc_9271-1.4.0.fw requested usb 1-1: ath9k_htc: Transferred FW: ath9k_htc/htc_9271-1.4.0.fw, size: 51008 usb 1-1: Service connection timeout for: 256 ================================================================== BUG: KASAN: use-after-free in atomic_read include/asm-generic/atomic-instrumented.h:26 [inline] BUG: KASAN: use-after-free in refcount_read include/linux/refcount.h:134 [inline] BUG: KASAN: use-after-free in skb_unref include/linux/skbuff.h:1042 [inline] BUG: KASAN: use-after-free in kfree_skb+0x32/0x3d0 net/core/skbuff.c:692 Read of size 4 at addr ffff8881d0957994 by task kworker/1:2/83 Call Trace: kfree_skb+0x32/0x3d0 net/core/skbuff.c:692 htc_connect_service.cold+0xa9/0x109 drivers/net/wireless/ath/ath9k/htc_hst.c:282 ath9k_wmi_connect+0xd2/0x1a0 drivers/net/wireless/ath/ath9k/wmi.c:265 ath9k_init_htc_services.constprop.0+0xb4/0x650 drivers/net/wireless/ath/ath9k/htc_drv_init.c:146 ath9k_htc_probe_device+0x25a/0x1d80 drivers/net/wireless/ath/ath9k/htc_drv_init.c:959 ath9k_htc_hw_init+0x31/0x60 drivers/net/wireless/ath/ath9k/htc_hst.c:501 ath9k_hif_usb_firmware_cb+0x26b/0x500 drivers/net/wireless/ath/ath9k/hif_usb.c:1187 request_firmware_work_func+0x126/0x242 drivers/base/firmware_loader/main.c:976 process_one_work+0x94b/0x1620 kernel/workqueue.c:2264 worker_thread+0x96/0xe20 kernel/workqueue.c:2410 kthread+0x318/0x420 kernel/kthread.c:255 ret_from_fork+0x24/0x30 arch/x86/entry/entry_64.S:352 Allocated by task 83: kmem_cache_alloc_node+0xdc/0x330 mm/slub.c:2814 __alloc_skb+0xba/0x5a0 net/core/skbuff.c:198 alloc_skb include/linux/skbuff.h:1081 [inline] htc_connect_service+0x2cc/0x840 drivers/net/wireless/ath/ath9k/htc_hst.c:257 ath9k_wmi_connect+0xd2/0x1a0 drivers/net/wireless/ath/ath9k/wmi.c:265 ath9k_init_htc_services.constprop.0+0xb4/0x650 drivers/net/wireless/ath/ath9k/htc_drv_init.c:146 ath9k_htc_probe_device+0x25a/0x1d80 drivers/net/wireless/ath/ath9k/htc_drv_init.c:959 ath9k_htc_hw_init+0x31/0x60 drivers/net/wireless/ath/ath9k/htc_hst.c:501 ath9k_hif_usb_firmware_cb+0x26b/0x500 drivers/net/wireless/ath/ath9k/hif_usb.c:1187 request_firmware_work_func+0x126/0x242 drivers/base/firmware_loader/main.c:976 process_one_work+0x94b/0x1620 kernel/workqueue.c:2264 worker_thread+0x96/0xe20 kernel/workqueue.c:2410 kthread+0x318/0x420 kernel/kthread.c:255 ret_from_fork+0x24/0x30 arch/x86/entry/entry_64.S:352 Freed by task 0: kfree_skb+0x102/0x3d0 net/core/skbuff.c:690 ath9k_htc_txcompletion_cb+0x1f8/0x2b0 drivers/net/wireless/ath/ath9k/htc_hst.c:356 hif_usb_regout_cb+0x10b/0x1b0 drivers/net/wireless/ath/ath9k/hif_usb.c:90 __usb_hcd_giveback_urb+0x29a/0x550 drivers/usb/core/hcd.c:1650 usb_hcd_giveback_urb+0x368/0x420 drivers/usb/core/hcd.c:1716 dummy_timer+0x1258/0x32ae drivers/usb/gadget/udc/dummy_hcd.c:1966 call_timer_fn+0x195/0x6f0 kernel/time/timer.c:1404 expire_timers kernel/time/timer.c:1449 [inline] __run_timers kernel/time/timer.c:1773 [inline] __run_timers kernel/time/timer.c:1740 [inline] run_timer_softirq+0x5f9/0x1500 kernel/time/timer.c:1786 __do_softirq+0x21e/0x950 kernel/softirq.c:292 Reported-and-tested-by: syzbot+9505af1ae303dabdc646@syzkaller.appspotmail.com Signed-off-by: Qiujun Huang <hqjagain@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200404041838.10426-2-hqjagain@gmail.com
* Merge ath-next from git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.gitKalle Valo2020-03-161-0/+3
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ath.git patches for v5.7. Major changes: ath10k * support for getting btcoex settings from Device Tree * support QCA9377 SDIO device ath11k * add HE rate accounting * add thermal sensor and cooling devices
| * ath9k: Handle txpower changes even when TPC is disabledRemi Pommarel2020-03-111-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When TPC is disabled IEEE80211_CONF_CHANGE_POWER event can be handled to reconfigure HW's maximum txpower. This fixes 0dBm txpower setting when user attaches to an interface for the first time with the following scenario: ieee80211_do_open() ath9k_add_interface() ath9k_set_txpower() /* Set TX power with not yet initialized sc->hw->conf.power_level */ ieee80211_hw_config() /* Iniatilize sc->hw->conf.power_level and raise IEEE80211_CONF_CHANGE_POWER */ ath9k_config() /* IEEE80211_CONF_CHANGE_POWER is ignored */ This issue can be reproduced with the following: $ modprobe -r ath9k $ modprobe ath9k $ wpa_supplicant -i wlan0 -c /tmp/wpa.conf & $ iw dev /* Here TX power is either 0 or 3 depending on RF chain */ $ killall wpa_supplicant $ iw dev /* TX power goes back to calibrated value and subsequent calls will be fine */ Fixes: 283dd11994cde ("ath9k: add per-vif TX power capability") Cc: stable@vger.kernel.org Signed-off-by: Remi Pommarel <repk@triplefau.lt> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* | Merge tag 'mac80211-next-for-net-next-2020-02-14' of ↵David S. Miller2020-02-162-2/+8
|\ \ | |/ |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next Johannes Berg says: ==================== A few big new things: * 802.11 frame encapsulation offload support * more HE (802.11ax) support, including some for 6 GHz band * powersave in hwsim, for better testing Of course as usual there are various cleanups and small fixes. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
| * mac80211: Fix setting txpower to zeroBen Greear2020-02-142-2/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | With multiple VIFS ath10k, and probably others, tries to find the minimum txpower for all vifs and uses that when setting txpower in the firmware. If a second vif is added and starts to scan, it's txpower is not initialized yet and it set to zero. ath10k had a patch to ignore zero values, but then it is impossible to actually set txpower to zero. So, instead initialize the txpower to INT_MIN in mac80211, and let drivers know that means the power has not been set and so should be ignored. This should fix regression in: commit 88407beb1b1462f706a1950a355fd086e1c450b6 Author: Ryan Hsu <ryanhsu@qca.qualcomm.com> Date: Tue Dec 13 14:55:19 2016 -0800 ath10k: fix incorrect txpower set by P2P_DEVICE interface Tested on ath10k 9984 with ath10k-ct firmware. Signed-off-by: Ben Greear <greearb@candelatech.com> Link: https://lore.kernel.org/r/20191217183057.24586-1-greearb@candelatech.com Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* | Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-nextLinus Torvalds2020-01-282-2/+2
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull networking updates from David Miller: 1) Add WireGuard 2) Add HE and TWT support to ath11k driver, from John Crispin. 3) Add ESP in TCP encapsulation support, from Sabrina Dubroca. 4) Add variable window congestion control to TIPC, from Jon Maloy. 5) Add BCM84881 PHY driver, from Russell King. 6) Start adding netlink support for ethtool operations, from Michal Kubecek. 7) Add XDP drop and TX action support to ena driver, from Sameeh Jubran. 8) Add new ipv4 route notifications so that mlxsw driver does not have to handle identical routes itself. From Ido Schimmel. 9) Add BPF dynamic program extensions, from Alexei Starovoitov. 10) Support RX and TX timestamping in igc, from Vinicius Costa Gomes. 11) Add support for macsec HW offloading, from Antoine Tenart. 12) Add initial support for MPTCP protocol, from Christoph Paasch, Matthieu Baerts, Florian Westphal, Peter Krystad, and many others. 13) Add Octeontx2 PF support, from Sunil Goutham, Geetha sowjanya, Linu Cherian, and others. * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1469 commits) net: phy: add default ARCH_BCM_IPROC for MDIO_BCM_IPROC udp: segment looped gso packets correctly netem: change mailing list qed: FW 8.42.2.0 debug features qed: rt init valid initialization changed qed: Debug feature: ilt and mdump qed: FW 8.42.2.0 Add fw overlay feature qed: FW 8.42.2.0 HSI changes qed: FW 8.42.2.0 iscsi/fcoe changes qed: Add abstraction for different hsi values per chip qed: FW 8.42.2.0 Additional ll2 type qed: Use dmae to write to widebus registers in fw_funcs qed: FW 8.42.2.0 Parser offsets modified qed: FW 8.42.2.0 Queue Manager changes qed: FW 8.42.2.0 Expose new registers and change windows qed: FW 8.42.2.0 Internal ram offsets modifications MAINTAINERS: Add entry for Marvell OcteonTX2 Physical Function driver Documentation: net: octeontx2: Add RVU HW and drivers overview octeontx2-pf: ethtool RSS config support octeontx2-pf: Add basic ethtool support ...
| * | ath9k: use true,false for bool variablezhengbin2020-01-261-1/+1
| |/ | | | | | | | | | | | | | | | | | | Fixes coccicheck warning: drivers/net/wireless/ath/ath9k/ar9003_aic.c:409:2-12: WARNING: Assignment of 0/1 to bool variable Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: zhengbin <zhengbin13@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netDavid S. Miller2019-12-221-1/+1
| |\ | | | | | | | | | | | | | | | Mere overlapping changes in the conflicts here. Signed-off-by: David S. Miller <davem@davemloft.net>
| * | ath9k: fix storage endpoint lookupJohan Hovold2019-12-181-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Make sure to use the current alternate setting when verifying the storage interface descriptors to avoid submitting an URB to an invalid endpoint. Failing to do so could cause the driver to misbehave or trigger a WARN() in usb_submit_urb() that kernels with panic_on_warn set would choke on. Fixes: 36bcce430657 ("ath9k_htc: Handle storage devices") Cc: stable <stable@vger.kernel.org> # 2.6.39 Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* | | remove ioremap_nocache and devm_ioremap_nocacheChristoph Hellwig2020-01-061-1/+1
| |/ |/| | | | | | | | | | | | | ioremap has provided non-cached semantics by default since the Linux 2.6 days, so remove the additional ioremap_nocache interface. Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: Arnd Bergmann <arnd@arndb.de>
* | ath9k: use iowrite32 over __raw_writelChristian Lamparter2019-11-281-1/+1
|/ | | | | | | | | | | | | This patch changes the ath9k_pci_owl_loader to use the same iowrite32 memory accessor that ath9k_pci is using to communicate with the PCI(e) chip. This will fix endian issues that came up during testing with loaned AVM Fritz!Box 7360 (Lantiq MIPS SoCs + AR9287). Fixes: 5a4f2040fd07 ("ath9k: add loader for AR92XX (and older) pci(e)") Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* drivers: net: Fix Kconfig indentation, continuedKrzysztof Kozlowski2019-11-211-29/+29
| | | | | | | | | Adjust indentation from spaces to tab (+optional two spaces) as in coding style. This fixes various indentation mixups (seven spaces, tab+one space, etc). Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge tag 'wireless-drivers-next-2019-11-05' of ↵David S. Miller2019-11-054-9/+22
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next Kalle Valo says: ==================== wireless-drivers-next patches for 5.5 First set of patches for 5.5. The most active driver here clearly is rtw88, lots of patches for it. More quiet on other drivers, smaller fixes and cleanups all over. This pull request also has a trivial conflict, the report and example resolution here: https://lkml.kernel.org/r/20191031111242.50ab1eca@canb.auug.org.au Major changes: rtw88 * add deep power save support * add mac80211 software tx queue (wake_tx_queue) support * enable hardware rate control * add TX-AMSDU support * add NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 support * add power tracking support * add 802.11ac beamformee support * add set_bitrate_mask support * add phy_info debugfs to show Tx/Rx physical status * add RFE type 3 support for 8822b ath10k * add support for hardware rfkill on devices where firmware supports it rtl8xxxu * add bluetooth co-existence support for single antenna iwlwifi * Revamp the debugging infrastructure ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
| * Merge ath-next from git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.gitKalle Valo2019-10-034-9/+22
| |\ | | | | | | | | | | | | | | | | | | | | | ath.git patches for 5.5. Major changes: ath10k * add support for hardware rfkill on devices where firmware supports it
| | * ath9k_htc: Discard undersized packetsMasashi Honma2019-10-011-4/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Sometimes the hardware will push small packets that trigger a WARN_ON in mac80211. Discard them early to avoid this issue. This patch ports 2 patches from ath9k to ath9k_htc. commit 3c0efb745a172bfe96459e20cbd37b0c945d5f8d "ath9k: discard undersized packets". commit df5c4150501ee7e86383be88f6490d970adcf157 "ath9k: correctly handle short radar pulses". [ 112.835889] ------------[ cut here ]------------ [ 112.835971] WARNING: CPU: 5 PID: 0 at net/mac80211/rx.c:804 ieee80211_rx_napi+0xaac/0xb40 [mac80211] [ 112.835973] Modules linked in: ath9k_htc ath9k_common ath9k_hw ath mac80211 cfg80211 libarc4 nouveau snd_hda_codec_hdmi intel_rapl_msr intel_rapl_common x86_pkg_temp_thermal intel_powerclamp coretemp snd_hda_codec_realtek snd_hda_codec_generic ledtrig_audio snd_hda_intel snd_hda_codec video snd_hda_core ttm snd_hwdep drm_kms_helper snd_pcm crct10dif_pclmul snd_seq_midi drm snd_seq_midi_event crc32_pclmul snd_rawmidi ghash_clmulni_intel snd_seq aesni_intel aes_x86_64 crypto_simd cryptd snd_seq_device glue_helper snd_timer sch_fq_codel i2c_algo_bit fb_sys_fops snd input_leds syscopyarea sysfillrect sysimgblt intel_cstate mei_me intel_rapl_perf soundcore mxm_wmi lpc_ich mei kvm_intel kvm mac_hid irqbypass parport_pc ppdev lp parport ip_tables x_tables autofs4 hid_generic usbhid hid raid10 raid456 async_raid6_recov async_memcpy async_pq async_xor async_tx xor raid6_pq libcrc32c raid1 raid0 multipath linear e1000e ahci libahci wmi [ 112.836022] CPU: 5 PID: 0 Comm: swapper/5 Not tainted 5.3.0-wt #1 [ 112.836023] Hardware name: MouseComputer Co.,Ltd. X99-S01/X99-S01, BIOS 1.0C-W7 04/01/2015 [ 112.836056] RIP: 0010:ieee80211_rx_napi+0xaac/0xb40 [mac80211] [ 112.836059] Code: 00 00 66 41 89 86 b0 00 00 00 e9 c8 fa ff ff 4c 89 b5 40 ff ff ff 49 89 c6 e9 c9 fa ff ff 48 c7 c7 e0 a2 a5 c0 e8 47 41 b0 e9 <0f> 0b 48 89 df e8 5a 94 2d ea e9 02 f9 ff ff 41 39 c1 44 89 85 60 [ 112.836060] RSP: 0018:ffffaa6180220da8 EFLAGS: 00010286 [ 112.836062] RAX: 0000000000000024 RBX: ffff909a20eeda00 RCX: 0000000000000000 [ 112.836064] RDX: 0000000000000000 RSI: ffff909a2f957448 RDI: ffff909a2f957448 [ 112.836065] RBP: ffffaa6180220e78 R08: 00000000000006e9 R09: 0000000000000004 [ 112.836066] R10: 000000000000000a R11: 0000000000000001 R12: 0000000000000000 [ 112.836068] R13: ffff909a261a47a0 R14: 0000000000000000 R15: 0000000000000004 [ 112.836070] FS: 0000000000000000(0000) GS:ffff909a2f940000(0000) knlGS:0000000000000000 [ 112.836071] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 112.836073] CR2: 00007f4e3ffffa08 CR3: 00000001afc0a006 CR4: 00000000001606e0 [ 112.836074] Call Trace: [ 112.836076] <IRQ> [ 112.836083] ? finish_td+0xb3/0xf0 [ 112.836092] ? ath9k_rx_prepare.isra.11+0x22f/0x2a0 [ath9k_htc] [ 112.836099] ath9k_rx_tasklet+0x10b/0x1d0 [ath9k_htc] [ 112.836105] tasklet_action_common.isra.22+0x63/0x110 [ 112.836108] tasklet_action+0x22/0x30 [ 112.836115] __do_softirq+0xe4/0x2da [ 112.836118] irq_exit+0xae/0xb0 [ 112.836121] do_IRQ+0x86/0xe0 [ 112.836125] common_interrupt+0xf/0xf [ 112.836126] </IRQ> [ 112.836130] RIP: 0010:cpuidle_enter_state+0xa9/0x440 [ 112.836133] Code: 3d bc 20 38 55 e8 f7 1d 84 ff 49 89 c7 0f 1f 44 00 00 31 ff e8 28 29 84 ff 80 7d d3 00 0f 85 e6 01 00 00 fb 66 0f 1f 44 00 00 <45> 85 ed 0f 89 ff 01 00 00 41 c7 44 24 10 00 00 00 00 48 83 c4 18 [ 112.836134] RSP: 0018:ffffaa61800e3e48 EFLAGS: 00000246 ORIG_RAX: ffffffffffffffde [ 112.836136] RAX: ffff909a2f96b340 RBX: ffffffffabb58200 RCX: 000000000000001f [ 112.836137] RDX: 0000001a458adc5d RSI: 0000000026c9b581 RDI: 0000000000000000 [ 112.836139] RBP: ffffaa61800e3e88 R08: 0000000000000002 R09: 000000000002abc0 [ 112.836140] R10: ffffaa61800e3e18 R11: 000000000000002d R12: ffffca617fb40b00 [ 112.836141] R13: 0000000000000002 R14: ffffffffabb582d8 R15: 0000001a458adc5d [ 112.836145] ? cpuidle_enter_state+0x98/0x440 [ 112.836149] ? menu_select+0x370/0x600 [ 112.836151] cpuidle_enter+0x2e/0x40 [ 112.836154] call_cpuidle+0x23/0x40 [ 112.836156] do_idle+0x204/0x280 [ 112.836159] cpu_startup_entry+0x1d/0x20 [ 112.836164] start_secondary+0x167/0x1c0 [ 112.836169] secondary_startup_64+0xa4/0xb0 [ 112.836173] ---[ end trace 9f4cd18479cc5ae5 ]--- Signed-off-by: Masashi Honma <masashi.honma@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| | * ath9k_htc: Modify byte order for an error messageMasashi Honma2019-10-011-1/+1
| | | | | | | | | | | | | | | | | | | | | rs_datalen is be16 so we need to convert it before printing. Signed-off-by: Masashi Honma <masashi.honma@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| | * ath9k_hw: fix uninitialized variable dataDenis Efremov2019-10-011-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently, data variable in ar9003_hw_thermo_cal_apply() could be uninitialized if ar9300_otp_read_word() will fail to read the value. Initialize data variable with 0 to prevent an undefined behavior. This will be enough to handle error case when ar9300_otp_read_word() fails. Fixes: 80fe43f2bbd5 ("ath9k_hw: Read and configure thermocal for AR9462") Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Cc: John W. Linville <linville@tuxdriver.com> Cc: Kalle Valo <kvalo@codeaurora.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: stable@vger.kernel.org Signed-off-by: Denis Efremov <efremov@linux.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| | * ath9k: remove unused including <linux/version.h>YueHaibing2019-10-011-1/+0
| | | | | | | | | | | | | | | | | | | | | Remove including <linux/version.h> that don't need it. Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| | * ath: Use dev_get_drvdata where possibleChuhong Yuan2019-09-231-3/+2
| | | | | | | | | | | | | | | | | | | | | | | | Instead of using to_pci_dev + pci_get_drvdata, use dev_get_drvdata to make code simpler. Signed-off-by: Chuhong Yuan <hslester96@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* | | net: Fix misspellings of "configure" and "configuration"Geert Uytterhoeven2019-10-281-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | Fix various misspellings of "configuration" and "configure". Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | mac80211: simplify TX aggregation startJohannes Berg2019-10-042-2/+2
|/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | There really is no need to make drivers call the ieee80211_start_tx_ba_cb_irqsafe() function and then schedule the worker if all we want is to set a bit. Add a new return value (that was previously considered invalid) to indicate that the driver is immediately ready for the session, and make drivers use it. The only drivers that remain different are the Intel ones as they need to negotiate more with the firmware. Link: https://lore.kernel.org/r/1570007543-I152912660131cbab2e5d80b4218238c20f8a06e5@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* / drivers: net: Fix Kconfig indentationKrzysztof Kozlowski2019-09-261-1/+1
|/ | | | | | | | | | | Adjust indentation from spaces to tab (+optional two spaces) as in coding style with command like: $ sed -e 's/^ /\t/' -i */Kconfig Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Acked-by: Kalle Valo <kvalo@codeaurora.org> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* ath9k: release allocated buffer if timed outNavid Emamdoost2019-09-101-0/+1
| | | | | | | | In ath9k_wmi_cmd, the allocated network buffer needs to be released if timeout happens. Otherwise memory will be leaked. Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* ath9k_htc: release allocated buffer if timed outNavid Emamdoost2019-09-101-0/+3
| | | | | | | | | In htc_config_pipe_credits, htc_setup_complete, and htc_connect_service if time out happens, the allocated buffer needs to be released. Otherwise there will be memory leak. Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* ath9k: Remove unneeded variable to store return valuezhong jiang2019-09-101-3/+1
| | | | | | | | ath9k_reg_rmw_single do not need return value to cope with different cases. And change functon return type to void. Signed-off-by: zhong jiang <zhongjiang@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* ath9k: dynack: set ackto to max timeout in ath_dynack_resetLorenzo Bianconi2019-09-041-7/+13
| | | | | | | | | | | | Initialize acktimeout to the maximum configurable value in ath_dynack_reset in order to not disconnect long distance static links enabling dynack and even to take care of possible errors configuring a static timeout. Moreover initialize station timeout value to the current acktimeout value Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* ath9k: dynack: set max timeout according to channel widthLorenzo Bianconi2019-09-041-8/+30
| | | | | | | | | Compute maximum configurable ackimeout/ctstimeout according to channel width (clockrate) Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* ath9k: dynack: properly set last timeout timestamp in ath_dynack_resetLorenzo Bianconi2019-09-041-1/+1
| | | | | | | | | | Add compute timeout to last computation timestamp in ath_dynack_reset in order to not run ath_dynack_compute_ackto immediately Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* ath9k: dyanck: introduce ath_dynack_set_timeout routineLorenzo Bianconi2019-09-041-16/+21
| | | | | | | | | Introduce ath_dynack_set_timeout routine to configure slottime/ack/cts timeouts and remove duplicated code Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* ath9k: dynack: fix possible deadlock in ath_dynack_node_{de}initLorenzo Bianconi2019-09-041-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix following lockdep warning disabling bh in ath_dynack_node_init/ath_dynack_node_deinit [ 75.955878] -------------------------------- [ 75.955880] inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage. [ 75.955884] swapper/0/0 [HC0[0]:SC1[3]:HE1:SE0] takes: [ 75.955888] 00000000792a7ee0 (&(&da->qlock)->rlock){+.?.}, at: ath_dynack_sample_ack_ts+0x4d/0xa0 [ath9k_hw] [ 75.955905] {SOFTIRQ-ON-W} state was registered at: [ 75.955912] lock_acquire+0x9a/0x160 [ 75.955917] _raw_spin_lock+0x2c/0x70 [ 75.955927] ath_dynack_node_init+0x2a/0x60 [ath9k_hw] [ 75.955934] ath9k_sta_state+0xec/0x160 [ath9k] [ 75.955976] drv_sta_state+0xb2/0x740 [mac80211] [ 75.956008] sta_info_insert_finish+0x21a/0x420 [mac80211] [ 75.956039] sta_info_insert_rcu+0x12b/0x2c0 [mac80211] [ 75.956069] sta_info_insert+0x7/0x70 [mac80211] [ 75.956093] ieee80211_prep_connection+0x42e/0x730 [mac80211] [ 75.956120] ieee80211_mgd_auth.cold+0xb9/0x15c [mac80211] [ 75.956152] cfg80211_mlme_auth+0x143/0x350 [cfg80211] [ 75.956169] nl80211_authenticate+0x25e/0x2b0 [cfg80211] [ 75.956172] genl_family_rcv_msg+0x198/0x400 [ 75.956174] genl_rcv_msg+0x42/0x90 [ 75.956176] netlink_rcv_skb+0x35/0xf0 [ 75.956178] genl_rcv+0x1f/0x30 [ 75.956180] netlink_unicast+0x154/0x200 [ 75.956182] netlink_sendmsg+0x1bf/0x3d0 [ 75.956186] ___sys_sendmsg+0x2c2/0x2f0 [ 75.956187] __sys_sendmsg+0x44/0x80 [ 75.956190] do_syscall_64+0x55/0x1a0 [ 75.956192] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 75.956194] irq event stamp: 2357092 [ 75.956196] hardirqs last enabled at (2357092): [<ffffffff818c62de>] _raw_spin_unlock_irqrestore+0x3e/0x50 [ 75.956199] hardirqs last disabled at (2357091): [<ffffffff818c60b1>] _raw_spin_lock_irqsave+0x11/0x80 [ 75.956202] softirqs last enabled at (2357072): [<ffffffff8106dc09>] irq_enter+0x59/0x60 [ 75.956204] softirqs last disabled at (2357073): [<ffffffff8106dcbe>] irq_exit+0xae/0xc0 [ 75.956206] other info that might help us debug this: [ 75.956207] Possible unsafe locking scenario: [ 75.956208] CPU0 [ 75.956209] ---- [ 75.956210] lock(&(&da->qlock)->rlock); [ 75.956213] <Interrupt> [ 75.956214] lock(&(&da->qlock)->rlock); [ 75.956216] *** DEADLOCK *** [ 75.956217] 1 lock held by swapper/0/0: [ 75.956219] #0: 000000003bb5675c (&(&sc->sc_pcu_lock)->rlock){+.-.}, at: ath9k_tasklet+0x55/0x240 [ath9k] [ 75.956225] stack backtrace: [ 75.956228] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.3.0-rc1-wdn+ #13 [ 75.956229] Hardware name: Dell Inc. Studio XPS 1340/0K183D, BIOS A11 09/08/2009 [ 75.956231] Call Trace: [ 75.956233] <IRQ> [ 75.956236] dump_stack+0x67/0x90 [ 75.956239] mark_lock+0x4c1/0x640 [ 75.956242] ? check_usage_backwards+0x130/0x130 [ 75.956245] ? sched_clock_local+0x12/0x80 [ 75.956247] __lock_acquire+0x484/0x7a0 [ 75.956250] ? __lock_acquire+0x3b9/0x7a0 [ 75.956252] lock_acquire+0x9a/0x160 [ 75.956259] ? ath_dynack_sample_ack_ts+0x4d/0xa0 [ath9k_hw] [ 75.956262] _raw_spin_lock_bh+0x34/0x80 [ 75.956268] ? ath_dynack_sample_ack_ts+0x4d/0xa0 [ath9k_hw] [ 75.956275] ath_dynack_sample_ack_ts+0x4d/0xa0 [ath9k_hw] [ 75.956280] ath_rx_tasklet+0xd09/0xe90 [ath9k] [ 75.956286] ath9k_tasklet+0x102/0x240 [ath9k] [ 75.956288] tasklet_action_common.isra.0+0x6d/0x170 [ 75.956291] __do_softirq+0xcc/0x425 [ 75.956294] irq_exit+0xae/0xc0 [ 75.956296] do_IRQ+0x8a/0x110 [ 75.956298] common_interrupt+0xf/0xf [ 75.956300] </IRQ> [ 75.956303] RIP: 0010:cpuidle_enter_state+0xb2/0x400 [ 75.956308] RSP: 0018:ffffffff82203e70 EFLAGS: 00000202 ORIG_RAX: ffffffffffffffd7 [ 75.956310] RAX: ffffffff82219800 RBX: ffffffff822bd0a0 RCX: 0000000000000000 [ 75.956312] RDX: 0000000000000046 RSI: 0000000000000006 RDI: ffffffff82219800 [ 75.956314] RBP: ffff888155a01c00 R08: 00000011af51aabe R09: 0000000000000000 [ 75.956315] R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000002 [ 75.956317] R13: 00000011af51aabe R14: 0000000000000003 R15: ffffffff82219800 [ 75.956321] cpuidle_enter+0x24/0x40 [ 75.956323] do_idle+0x1ac/0x220 [ 75.956326] cpu_startup_entry+0x14/0x20 [ 75.956329] start_kernel+0x482/0x489 [ 75.956332] secondary_startup_64+0xa4/0xb0 Fixes: c774d57fd47c ("ath9k: add dynamic ACK timeout estimation") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* ath9k: add loader for AR92XX (and older) pci(e)Christian Lamparter2019-09-043-0/+233
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Atheros cards with a AR92XX generation (and older) chip usually store their pci(e) initialization vectors on an external eeprom chip. However these chips technically don't need the eeprom chip attached, the AR9280 Datasheet in section "6.1.2 DEVICE_ID" describes that "... if the EEPROM content is not valid, a value of 0xFF1C returns when read from the register". So, they will show up on the system's pci bus. However in that state, ath9k can't load, since it relies on having the correct pci-id, otherwise it doesn't know what chip it actually is. This happens on many embedded devices like routers and accesspoint since they want to keep the BOM low and store the pci(e) initialization vectors together with the calibration data on the system's FLASH, which is out of reach of the ath9k chip. Furthermore, Some devices (like the Cisco Meraki Z1 Cloud Managed Teleworker Gateway) need to be able to initialize the PCIe wifi device. Normally, this should be done as a pci quirk during the early stages of booting linux. However, this isn't possible for devices which have the init code for the Atheros chip stored on NAND in an UBI volume. Hence, this module can be used to initialize the chip when the user-space is ready to extract the init code. Martin Blumenstingl prodived the following fixes: owl-loader: add support for OWL emulation PCI devices owl-loader: don't re-scan the bus when ath9k_pci_fixup failed owl-loader: use dev_* instead of pr_* logging functions owl-loader: auto-generate the eeprom filename as fallback owl-loader: add a debug message when swapping the eeprom data owl-loader: add missing newlines in log messages Reviewed-by: Julian Calaby <julian.calaby@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* mac80211: pass the vif to cancel_remain_on_channelEmmanuel Grumbach2019-07-261-1/+2
| | | | | | | | | | | This low level driver can find it useful to get the vif when a remain on channel session is cancelled. iwlwifi will need this soon. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Link: https://lore.kernel.org/r/20190723180001.5828-1-emmanuel.grumbach@intel.com Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2019-07-082-2/+2
|\ | | | | | | | | | | Two cases of overlapping changes, nothing fancy. Signed-off-by: David S. Miller <davem@davemloft.net>
| * ath: fix SPDX tagsKalle Valo2019-06-262-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit ec8f24b7faaf ("treewide: Add SPDX license identifier - Makefile/Kconfig") marked various Makefiles and Kconfig files within ath directories as GPL-2.0. But these modules and drivers are actually ISC: * ath * ar5523 * ath10k * ath5k * ath6kl * ath9k * wcn36xx * wil6210 Fix SPDX tags accordingly. Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* | ath9k: correctly handle short radar pulsesZefir Kurtisi2019-06-271-1/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In commit 3c0efb745a17 ("ath9k: discard undersized packets") the lower bound of RX packets was set to 10 (min ACK size) to filter those that would otherwise be treated as invalid at mac80211. Alas, short radar pulses are reported as PHY_ERROR frames with length set to 3. Therefore their detection stopped working after that commit. NOTE: ath9k drivers built thereafter will not pass DFS certification. This extends the criteria for short packets to explicitly handle PHY_ERROR frames. Fixes: 3c0efb745a17 ("ath9k: discard undersized packets") Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* | Merge ath-next from git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.gitKalle Valo2019-05-277-50/+38
|\ \ | |/ |/| | | | | | | | | | | ath.git patches for 5.3. Major changes: ath10k * enable SDIO support, first one being QCA6174 hw3.2
| * ath9k: drop redundant code in ar9003_hw_set_channelTomislav Požega2019-04-291-21/+3
| | | | | | | | | | | | | | | | | | AR9330, AR9485, AR9531, AR9550, AR9561 and AR9565 all use same channel set register configuration which allows for small code size reduction. Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * ath9k: Remove some set but not used variablesYueHaibing2019-04-291-11/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fixes gcc '-Wunused-but-set-variable' warning: drivers/net/wireless/ath/ath9k/xmit.c: In function 'ath_tx_count_frames': drivers/net/wireless/ath/ath9k/xmit.c:413:25: warning: variable 'fi' set but not used [-Wunused-but-set-variable] drivers/net/wireless/ath/ath9k/xmit.c: In function 'ath_tx_complete_aggr': drivers/net/wireless/ath/ath9k/xmit.c:449:24: warning: variable 'hdr' set but not used [-Wunused-but-set-variable] drivers/net/wireless/ath/ath9k/xmit.c: In function 'ath_tx_start': drivers/net/wireless/ath/ath9k/xmit.c:2274:18: warning: variable 'avp' set but not used [-Wunused-but-set-variable] drivers/net/wireless/ath/ath9k/xmit.c:2269:24: warning: variable 'hdr' set but not used [-Wunused-but-set-variable] These variables are not used any more and can be removed. Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * ath9k: Differentiate between max combined and per chain powerSven Eckelmann2019-04-295-6/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ath9k driver uses as maximum allowed txpower the constant MAX_RATE_POWER. It is used to set a maximum txpower limit for the PHY (which is combined txpower) and also the maximum txpower for per chain rates. Its value 63 is derived from the maximum number the registers can store for the per chain txpower. The max txpower a user can set because of this is 31 dBm (floor(63 / 2)). This also means that a device with multiple tx chains is even limited further: * 1 chain: 31 dBm per chain * 2 chains: 28 dBm per chain * 3 chains: 26 dBm per chain This combined txpower limit of 31 dBm becomes even more problematic when some extra antenna gain is set in the EEPROM. A high power device is then no longer able to reach its potential limits. Instead the code dealing with the combined txpower must use a higher limit than 63 and only the code dealing with the per chain txpower have to use the limit of 63. Since the antenna gain can be quite large and 8 bit variables are often used in ath9k for txpower, a large, divisible by two number like 254 is a good choice for this new limit. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * ath9k: Check for errors when reading SREV registerTim Schumacher2019-04-291-9/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Right now, if an error is encountered during the SREV register read (i.e. an EIO in ath9k_regread()), that error code gets passed all the way to __ath9k_hw_init(), where it is visible during the "Chip rev not supported" message. ath9k_htc 1-1.4:1.0: ath9k_htc: HTC initialized with 33 credits ath: phy2: Mac Chip Rev 0x0f.3 is not supported by this driver ath: phy2: Unable to initialize hardware; initialization status: -95 ath: phy2: Unable to initialize hardware; initialization status: -95 ath9k_htc: Failed to initialize the device Check for -EIO explicitly in ath9k_hw_read_revisions() and return a boolean based on the success of the operation. Check for that in __ath9k_hw_init() and abort with a more debugging-friendly message if reading the revisions wasn't successful. ath9k_htc 1-1.4:1.0: ath9k_htc: HTC initialized with 33 credits ath: phy2: Failed to read SREV register ath: phy2: Could not read hardware revision ath: phy2: Unable to initialize hardware; initialization status: -95 ath: phy2: Unable to initialize hardware; initialization status: -95 ath9k_htc: Failed to initialize the device This helps when debugging by directly showing the first point of failure and it could prevent possible errors if a 0x0f.3 revision is ever supported. Signed-off-by: Tim Schumacher <timschumi@gmx.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * ath9k: Don't trust TX status TID number when reporting airtimeToke Høiland-Jørgensen2019-04-291-3/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | As already noted a comment in ath_tx_complete_aggr(), the hardware will occasionally send a TX status with the wrong tid number. If we trust the value, airtime usage will be reported to the wrong AC, which can cause the deficit on that AC to become very low, blocking subsequent attempts to transmit. To fix this, account airtime usage to the TID number from the original skb, instead of the one in the hardware TX status report. Reported-by: Miguel Catalan Cid <miguel.catalan@i2cat.net> Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* | treewide: Add SPDX license identifier - Makefile/KconfigThomas Gleixner2019-05-211-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Add SPDX license identifiers to all Make/Kconfig files which: - Have no license information of any form These files fall under the project license, GPL v2 only. The resulting SPDX license identifier is: GPL-2.0-only Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | net: wireless: support of_get_mac_address new ERR_PTR errorPetr Štetiar2019-05-051-1/+1
|/ | | | | | | | | There was NVMEM support added to of_get_mac_address, so it could now return ERR_PTR encoded error values, so we need to adjust all current users of of_get_mac_address to this new fact. Signed-off-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
* mac80211: make ieee80211_schedule_txq schedule empty TXQsFelix Fietkau2019-04-081-1/+4
| | | | | | | | | | | | | | | | | | | | | | Currently there is no way for the driver to signal to mac80211 that it should schedule a TXQ even if there are no packets on the mac80211 part of that queue. This is problematic if the driver has an internal retry queue to deal with software A-MPDU retry. This patch changes the behavior of ieee80211_schedule_txq to always schedule the queue, as its only user (ath9k) seems to expect such behavior already: it calls this function on tx status and on powersave wakeup whenever its internal retry queue is not empty. Also add an extra argument to ieee80211_return_txq to get the same behavior. This fixes an issue on ath9k where tx queues with packets to retry (and no new packets in mac80211) would not get serviced. Fixes: 89cea7493a346 ("ath9k: Switch to mac80211 TXQ scheduling and airtime APIs") Signed-off-by: Felix Fietkau <nbd@nbd.name> Acked-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* ath9k: remove set but not used variable 'acq'YueHaibing2019-02-261-8/+1
| | | | | | | | | | | | | | | Fixes gcc '-Wunused-but-set-variable' warning: drivers/net/wireless/ath/ath9k/recv.c: In function 'ath_rx_count_airtime': drivers/net/wireless/ath/ath9k/recv.c:1010:18: warning: variable 'acq' set but not used [-Wunused-but-set-variable] It's not used after 89cea7493a34 ("ath9k: Switch to mac80211 TXQ scheduling and airtime APIs"). Also remove related variables. Signed-off-by: YueHaibing <yuehaibing@huawei.com> Acked-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
generated by cgit (git 2.34.1) at 2025-02-28 07:50:36 +0000