aboutsummaryrefslogtreecommitdiffstats
path: root/drivers
Commit message (Collapse)AuthorAgeFilesLines
* virtio-blk: Use kobj_to_dev() instead of container_of()Tian Tao2020-09-011-1/+1
| | | | | | | | | | Use kobj_to_dev() instead of container_of() Signed-off-by: Tian Tao <tiantao6@hisilicon.com> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Reviewed-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
* raw: deprecate the raw driverChristoph Hellwig2020-09-011-0/+5
| | | | | | | | The raw driver has been replaced by O_DIRECT support on the block device in 2002. Deprecate it to prepare for removal in a few kernel releases. Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
* nvme: don't call revalidate_disk from nvme_set_queue_dyingChristoph Hellwig2020-09-012-23/+23
| | | | | | | | | | | | | | | In nvme_set_queue_dying we really just want to ensure the disk and bdev sizes are set to zero. Going through revalidate_disk leads to a somewhat arcance and complex callchain relying on special behavior in a few places. Instead just lift the set_capacity directly to nvme_set_queue_dying, and rename and move the nvme_mpath_update_disk_size helper so that we can use it in nvme_set_queue_dying to propagate the size to the bdev without detours. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
* block: fix locking for struct block_device size updatesChristoph Hellwig2020-09-013-23/+5
| | | | | | | | | | | | | | | | | | | | Two different callers use two different mutexes for updating the block device size, which obviously doesn't help to actually protect against concurrent updates from the different callers. In addition one of the locks, bd_mutex is rather prone to deadlocks with other parts of the block stack that use it for high level synchronization. Switch to using a new spinlock protecting just the size updates, as that is all we need, and make sure everyone does the update through the proper helper. This fixes a bug reported with the nvme revalidating disks during a hot removal operation, which can currently deadlock on bd_mutex. Reported-by: Xianting Tian <xianting_tian@126.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Jens Axboe <axboe@kernel.dk>
* block: replace bd_set_size with bd_set_nr_sectorsChristoph Hellwig2020-09-014-7/+8
| | | | | | | | | | Replace bd_set_size with a version that takes the number of sectors instead, as that fits most of the current and future callers much better. Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Jens Axboe <axboe@kernel.dk>
* Merge branch 'block-5.9' into for-5.10/blockJens Axboe2020-09-018-58/+167
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * block-5.9: blk-stat: make q->stats->lock irqsafe blk-iocost: ioc_pd_free() shouldn't assume irq disabled block: fix locking in bdev_del_partition block: release disk reference in hd_struct_free_work block: ensure bdi->io_pages is always initialized nvme-pci: cancel nvme device request before disabling nvme: only use power of two io boundaries nvme: fix controller instance leak nvmet-fc: Fix a missed _irqsave version of spin_lock in 'nvmet_fc_fod_op_done()' nvme: Fix NULL dereference for pci nvme controllers nvme-rdma: fix reset hang if controller died in the middle of a reset nvme-rdma: fix timeout handler nvme-rdma: serialize controller teardown sequences nvme-tcp: fix reset hang if controller died in the middle of a reset nvme-tcp: fix timeout handler nvme-tcp: serialize controller teardown sequences nvme: have nvme_wait_freeze_timeout return if it timed out nvme-fabrics: don't check state NVME_CTRL_NEW for request acceptance nvmet-tcp: Fix NULL dereference when a connect data comes in h2cdata pdu
| * nvme-pci: cancel nvme device request before disablingTong Zhang2020-08-281-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch addresses an irq free warning and null pointer dereference error problem when nvme devices got timeout error during initialization. This problem happens when nvme_timeout() function is called while nvme_reset_work() is still in execution. This patch fixed the problem by setting flag of the problematic request to NVME_REQ_CANCELLED before calling nvme_dev_disable() to make sure __nvme_submit_sync_cmd() returns an error code and let nvme_submit_sync_cmd() fail gracefully. The following is console output. [ 62.472097] nvme nvme0: I/O 13 QID 0 timeout, disable controller [ 62.488796] nvme nvme0: could not set timestamp (881) [ 62.494888] ------------[ cut here ]------------ [ 62.495142] Trying to free already-free IRQ 11 [ 62.495366] WARNING: CPU: 0 PID: 7 at kernel/irq/manage.c:1751 free_irq+0x1f7/0x370 [ 62.495742] Modules linked in: [ 62.495902] CPU: 0 PID: 7 Comm: kworker/u4:0 Not tainted 5.8.0+ #8 [ 62.496206] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.13.0-48-gd9c812dda519-p4 [ 62.496772] Workqueue: nvme-reset-wq nvme_reset_work [ 62.497019] RIP: 0010:free_irq+0x1f7/0x370 [ 62.497223] Code: e8 ce 49 11 00 48 83 c4 08 4c 89 e0 5b 5d 41 5c 41 5d 41 5e 41 5f c3 44 89 f6 48 c70 [ 62.498133] RSP: 0000:ffffa96800043d40 EFLAGS: 00010086 [ 62.498391] RAX: 0000000000000000 RBX: ffff9b87fc458400 RCX: 0000000000000000 [ 62.498741] RDX: 0000000000000001 RSI: 0000000000000096 RDI: ffffffff9693d72c [ 62.499091] RBP: ffff9b87fd4c8f60 R08: ffffa96800043bfd R09: 0000000000000163 [ 62.499440] R10: ffffa96800043bf8 R11: ffffa96800043bfd R12: ffff9b87fd4c8e00 [ 62.499790] R13: ffff9b87fd4c8ea4 R14: 000000000000000b R15: ffff9b87fd76b000 [ 62.500140] FS: 0000000000000000(0000) GS:ffff9b87fdc00000(0000) knlGS:0000000000000000 [ 62.500534] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 62.500816] CR2: 0000000000000000 CR3: 000000003aa0a000 CR4: 00000000000006f0 [ 62.501165] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 62.501515] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 62.501864] Call Trace: [ 62.501993] pci_free_irq+0x13/0x20 [ 62.502167] nvme_reset_work+0x5d0/0x12a0 [ 62.502369] ? update_load_avg+0x59/0x580 [ 62.502569] ? ttwu_queue_wakelist+0xa8/0xc0 [ 62.502780] ? try_to_wake_up+0x1a2/0x450 [ 62.502979] process_one_work+0x1d2/0x390 [ 62.503179] worker_thread+0x45/0x3b0 [ 62.503361] ? process_one_work+0x390/0x390 [ 62.503568] kthread+0xf9/0x130 [ 62.503726] ? kthread_park+0x80/0x80 [ 62.503911] ret_from_fork+0x22/0x30 [ 62.504090] ---[ end trace de9ed4a70f8d71e2 ]--- [ 123.912275] nvme nvme0: I/O 12 QID 0 timeout, disable controller [ 123.914670] nvme nvme0: 1/0/0 default/read/poll queues [ 123.916310] BUG: kernel NULL pointer dereference, address: 0000000000000000 [ 123.917469] #PF: supervisor write access in kernel mode [ 123.917725] #PF: error_code(0x0002) - not-present page [ 123.917976] PGD 0 P4D 0 [ 123.918109] Oops: 0002 [#1] SMP PTI [ 123.918283] CPU: 0 PID: 7 Comm: kworker/u4:0 Tainted: G W 5.8.0+ #8 [ 123.918650] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.13.0-48-gd9c812dda519-p4 [ 123.919219] Workqueue: nvme-reset-wq nvme_reset_work [ 123.919469] RIP: 0010:__blk_mq_alloc_map_and_request+0x21/0x80 [ 123.919757] Code: 66 0f 1f 84 00 00 00 00 00 41 55 41 54 55 48 63 ee 53 48 8b 47 68 89 ee 48 89 fb 8b4 [ 123.920657] RSP: 0000:ffffa96800043d40 EFLAGS: 00010286 [ 123.920912] RAX: ffff9b87fc4fee40 RBX: ffff9b87fc8cb008 RCX: 0000000000000000 [ 123.921258] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff9b87fc618000 [ 123.921602] RBP: 0000000000000000 R08: ffff9b87fdc2c4a0 R09: ffff9b87fc616000 [ 123.921949] R10: 0000000000000000 R11: ffff9b87fffd1500 R12: 0000000000000000 [ 123.922295] R13: 0000000000000000 R14: ffff9b87fc8cb200 R15: ffff9b87fc8cb000 [ 123.922641] FS: 0000000000000000(0000) GS:ffff9b87fdc00000(0000) knlGS:0000000000000000 [ 123.923032] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 123.923312] CR2: 0000000000000000 CR3: 000000003aa0a000 CR4: 00000000000006f0 [ 123.923660] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 123.924007] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 123.924353] Call Trace: [ 123.924479] blk_mq_alloc_tag_set+0x137/0x2a0 [ 123.924694] nvme_reset_work+0xed6/0x12a0 [ 123.924898] process_one_work+0x1d2/0x390 [ 123.925099] worker_thread+0x45/0x3b0 [ 123.925280] ? process_one_work+0x390/0x390 [ 123.925486] kthread+0xf9/0x130 [ 123.925642] ? kthread_park+0x80/0x80 [ 123.925825] ret_from_fork+0x22/0x30 [ 123.926004] Modules linked in: [ 123.926158] CR2: 0000000000000000 [ 123.926322] ---[ end trace de9ed4a70f8d71e3 ]--- [ 123.926549] RIP: 0010:__blk_mq_alloc_map_and_request+0x21/0x80 [ 123.926832] Code: 66 0f 1f 84 00 00 00 00 00 41 55 41 54 55 48 63 ee 53 48 8b 47 68 89 ee 48 89 fb 8b4 [ 123.927734] RSP: 0000:ffffa96800043d40 EFLAGS: 00010286 [ 123.927989] RAX: ffff9b87fc4fee40 RBX: ffff9b87fc8cb008 RCX: 0000000000000000 [ 123.928336] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff9b87fc618000 [ 123.928679] RBP: 0000000000000000 R08: ffff9b87fdc2c4a0 R09: ffff9b87fc616000 [ 123.929025] R10: 0000000000000000 R11: ffff9b87fffd1500 R12: 0000000000000000 [ 123.929370] R13: 0000000000000000 R14: ffff9b87fc8cb200 R15: ffff9b87fc8cb000 [ 123.929715] FS: 0000000000000000(0000) GS:ffff9b87fdc00000(0000) knlGS:0000000000000000 [ 123.930106] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 123.930384] CR2: 0000000000000000 CR3: 000000003aa0a000 CR4: 00000000000006f0 [ 123.930731] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 123.931077] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Co-developed-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Tong Zhang <ztong0001@gmail.com> Reviewed-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
| * nvme: only use power of two io boundariesKeith Busch2020-08-281-9/+38
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The kernel requires a power of two for boundaries because that's the only way it can efficiently split commands that cross them. A controller, however, may report a non-power of two boundary. The driver had been rounding the controller's value to one the kernel can use, but splitting on the wrong boundary provides no benefit on the device side, and incurs additional submission overhead from non-optimal splits. Don't provide any boundary hint if the controller's value can't be used and log a warning when first scanning a disk's unreported IO boundary. Since the chunk sector logic has grown, move it to a separate function. Cc: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Keith Busch <kbusch@kernel.org> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
| * nvme: fix controller instance leakKeith Busch2020-08-281-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | If the driver has to unbind from the controller for an early failure before the subsystem has been set up, there won't be a subsystem holding the controller's instance, so the controller needs to free its own instance in this case. Fixes: 733e4b69d508d ("nvme: Assign subsys instance from first ctrl") Signed-off-by: Keith Busch <kbusch@kernel.org> Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
| * nvmet-fc: Fix a missed _irqsave version of spin_lock in 'nvmet_fc_fod_op_done()'Christophe JAILLET2020-08-281-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | The way 'spin_lock()' and 'spin_lock_irqsave()' are used is not consistent in this function. Use 'spin_lock_irqsave()' also here, as there is no guarantee that interruptions are disabled at that point, according to surrounding code. Fixes: a97ec51b37ef ("nvmet_fc: Rework target side abort handling") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
| * nvme: Fix NULL dereference for pci nvme controllersSagi Grimberg2020-08-281-0/+4
| | | | | | | | | | | | | | | | | | | | PCIe controllers do not have fabric opts, verify they exist before showing ctrl_loss_tmo or reconnect_delay attributes. Fixes: 764075fdcb2f ("nvme: expose reconnect_delay and ctrl_loss_tmo via sysfs") Reported-by: Tobias Markus <tobias@markus-regensburg.de> Reviewed-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
| * nvme-rdma: fix reset hang if controller died in the middle of a resetSagi Grimberg2020-08-281-1/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | If the controller becomes unresponsive in the middle of a reset, we will hang because we are waiting for the freeze to complete, but that cannot happen since we have commands that are inflight holding the q_usage_counter, and we can't blindly fail requests that times out. So give a timeout and if we cannot wait for queue freeze before unfreezing, fail and have the error handling take care how to proceed (either schedule a reconnect of remove the controller). Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
| * nvme-rdma: fix timeout handlerSagi Grimberg2020-08-281-16/+33
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When a request times out in a LIVE state, we simply trigger error recovery and let the error recovery handle the request cancellation, however when a request times out in a non LIVE state, we make sure to complete it immediately as it might block controller setup or teardown and prevent forward progress. However tearing down the entire set of I/O and admin queues causes freeze/unfreeze imbalance (q->mq_freeze_depth) because and is really an overkill to what we actually need, which is to just fence controller teardown that may be running, stop the queue, and cancel the request if it is not already completed. Now that we have the controller teardown_lock, we can safely serialize request cancellation. This addresses a hang caused by calling extra queue freeze on controller namespaces, causing unfreeze to not complete correctly. Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: James Smart <james.smart@broadcom.com> Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
| * nvme-rdma: serialize controller teardown sequencesSagi Grimberg2020-08-281-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In the timeout handler we may need to complete a request because the request that timed out may be an I/O that is a part of a serial sequence of controller teardown or initialization. In order to complete the request, we need to fence any other context that may compete with us and complete the request that is timing out. In this case, we could have a potential double completion in case a hard-irq or a different competing context triggered error recovery and is running inflight request cancellation concurrently with the timeout handler. Protect using a ctrl teardown_lock to serialize contexts that may complete a cancelled request due to error recovery or a reset. Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: James Smart <james.smart@broadcom.com> Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
| * nvme-tcp: fix reset hang if controller died in the middle of a resetSagi Grimberg2020-08-281-1/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | If the controller becomes unresponsive in the middle of a reset, we will hang because we are waiting for the freeze to complete, but that cannot happen since we have commands that are inflight holding the q_usage_counter, and we can't blindly fail requests that times out. So give a timeout and if we cannot wait for queue freeze before unfreezing, fail and have the error handling take care how to proceed (either schedule a reconnect of remove the controller). Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
| * nvme-tcp: fix timeout handlerSagi Grimberg2020-08-281-20/+36
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When a request times out in a LIVE state, we simply trigger error recovery and let the error recovery handle the request cancellation, however when a request times out in a non LIVE state, we make sure to complete it immediately as it might block controller setup or teardown and prevent forward progress. However tearing down the entire set of I/O and admin queues causes freeze/unfreeze imbalance (q->mq_freeze_depth) because and is really an overkill to what we actually need, which is to just fence controller teardown that may be running, stop the queue, and cancel the request if it is not already completed. Now that we have the controller teardown_lock, we can safely serialize request cancellation. This addresses a hang caused by calling extra queue freeze on controller namespaces, causing unfreeze to not complete correctly. Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
| * nvme-tcp: serialize controller teardown sequencesSagi Grimberg2020-08-281-2/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In the timeout handler we may need to complete a request because the request that timed out may be an I/O that is a part of a serial sequence of controller teardown or initialization. In order to complete the request, we need to fence any other context that may compete with us and complete the request that is timing out. In this case, we could have a potential double completion in case a hard-irq or a different competing context triggered error recovery and is running inflight request cancellation concurrently with the timeout handler. Protect using a ctrl teardown_lock to serialize contexts that may complete a cancelled request due to error recovery or a reset. Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
| * nvme: have nvme_wait_freeze_timeout return if it timed outSagi Grimberg2020-08-282-2/+3
| | | | | | | | | | | | | | | | | | | | Users can detect if the wait has completed or not and take appropriate actions based on this information (e.g. weather to continue initialization or rather fail and schedule another initialization attempt). Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
| * nvme-fabrics: don't check state NVME_CTRL_NEW for request acceptanceSagi Grimberg2020-08-281-1/+0
| | | | | | | | | | | | | | | | | | NVME_CTRL_NEW should never see any I/O, because in order to start initialization it has to transition to NVME_CTRL_CONNECTING and from there it will never return to this state. Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
| * nvmet-tcp: Fix NULL dereference when a connect data comes in h2cdata pduZiye Yang2020-08-281-1/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When handling commands without in-capsule data, we assign the ttag assuming we already have the queue commands array allocated (based on the queue size information in the connect data payload). However if the connect itself did not send the connect data in-capsule we have yet to allocate the queue commands,and we will assign a bogus ttag and suffer a NULL dereference when we receive the corresponding h2cdata pdu. Fix this by checking if we already allocated commands before dereferencing it when handling h2cdata, if we didn't, its for sure a connect and we should use the preallocated connect command. Signed-off-by: Ziye Yang <ziye.yang@intel.com> Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
* | Merge branch 'linus' of ↵Linus Torvalds2020-08-303-10/+9
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6 Pull crypto fixes from Herbert Xu: - fix regression in af_alg that affects iwd - restore polling delay in qat - fix double free in ingenic on error path - fix potential build failure in sa2ul due to missing Kconfig dependency * 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: crypto: af_alg - Work around empty control messages without MSG_MORE crypto: sa2ul - add Kconfig selects to fix build error crypto: ingenic - Drop kfree for memory allocated with devm_kzalloc crypto: qat - add delay before polling mailbox
| * | crypto: sa2ul - add Kconfig selects to fix build errorRandy Dunlap2020-08-211-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | sa2ul.c uses sha{1,256,512}_zero_message_hash, so select the Kconfig symbols that provide those, like other crypto drivers do. Fixes this build error: ld: drivers/crypto/sa2ul.o: in function `sa_sha_digest': sa2ul.c:(.text+0x2b25): undefined reference to `sha512_zero_message_hash' Fixes: 7694b6ca649f ("crypto: sa2ul - Add crypto driver") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: Randy Dunlap <rdunlap@infradead.org> # 2020-07-29 Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: "David S. Miller" <davem@davemloft.net> Cc: linux-crypto@vger.kernel.org Cc: Tero Kristo <t-kristo@ti.com> Cc: Keerthy <j-keerthy@ti.com> Reviewed-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
| * | crypto: ingenic - Drop kfree for memory allocated with devm_kzallocWei Yongjun2020-08-211-7/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It's not necessary to free memory allocated with devm_kzalloc and using kfree leads to a double free. Fixes: 190873a0ea45 ("crypto: ingenic - Add hardware RNG for Ingenic JZ4780 and X1000") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Reviewed-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
| * | crypto: qat - add delay before polling mailboxGiovanni Cabiddu2020-08-211-3/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The mailbox CSR register has a write latency and requires a delay before being read. This patch replaces readl_poll_timeout with read_poll_timeout that allows to sleep before read. The initial sleep was removed when the mailbox poll loop was replaced with readl_poll_timeout. Fixes: a79d471c6510 ("crypto: qat - update timeout logic in put admin msg") Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
* | | Merge tag 'irq-urgent-2020-08-30' of ↵Linus Torvalds2020-08-3010-180/+258
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull irq fixes from Thomas Gleixner: "A set of fixes for interrupt chip drivers: - Revert the platform driver conversion of interrupt chip drivers as it turned out to create more problems than it solves. - Fix a trivial typo in the new module helpers which made probing reliably fail. - Small fixes in the STM32 and MIPS Ingenic drivers - The TI firmware rework which had badly managed dependencies and had to wait post rc1" * tag 'irq-urgent-2020-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: irqchip/ingenic: Leave parent IRQ unmasked on suspend irqchip/stm32-exti: Avoid losing interrupts due to clearing pending bits by mistake irqchip: Revert modular support for drivers using IRQCHIP_PLATFORM_DRIVER helperse irqchip: Fix probing deferal when using IRQCHIP_PLATFORM_DRIVER helpers arm64: dts: k3-am65: Update the RM resource types arm64: dts: k3-am65: ti-sci-inta/intr: Update to latest bindings arm64: dts: k3-j721e: ti-sci-inta/intr: Update to latest bindings irqchip/ti-sci-inta: Add support for INTA directly connecting to GIC irqchip/ti-sci-inta: Do not store TISCI device id in platform device id field dt-bindings: irqchip: Convert ti, sci-inta bindings to yaml dt-bindings: irqchip: ti, sci-inta: Update docs to support different parent. irqchip/ti-sci-intr: Add support for INTR being a parent to INTR dt-bindings: irqchip: Convert ti, sci-intr bindings to yaml dt-bindings: irqchip: ti, sci-intr: Update bindings to drop the usage of gic as parent firmware: ti_sci: Add support for getting resource with subtype firmware: ti_sci: Drop unused structure ti_sci_rm_type_map firmware: ti_sci: Drop the device id to resource type translation
| * | | irqchip/ingenic: Leave parent IRQ unmasked on suspendPaul Cercueil2020-08-251-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | All the wakeup sources we possibly want will go through the interrupt controller, so the parent IRQ must not be masked during suspend, or there won't be any way to wake up the system. Signed-off-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20200819180602.136969-1-paul@crapouillou.net
| * | | irqchip/stm32-exti: Avoid losing interrupts due to clearing pending bits by ↵qiuguorui12020-08-251-2/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | mistake In the current code, when the eoi callback of the exti clears the pending bit of the current interrupt, it will first read the values of fpr and rpr, then logically OR the corresponding bit of the interrupt number, and finally write back to fpr and rpr. We found through experiments that if two exti interrupts, we call them int1/int2, arrive almost at the same time. in our scenario, the time difference is 30 microseconds, assuming int1 is triggered first. there will be an extreme scenario: both int's pending bit are set to 1, the irq handle of int1 is executed first, and eoi handle is then executed, at this moment, all pending bits are cleared, but the int 2 has not finally been reported to the cpu yet, which eventually lost int2. According to stm32's TRM description about rpr and fpr: Writing a 1 to this bit will trigger a rising edge event on event x, Writing 0 has no effect. Therefore, when clearing the pending bit, we only need to clear the pending bit of the irq. Fixes: 927abfc4461e7 ("irqchip/stm32: Add stm32mp1 support with hierarchy domain") Signed-off-by: qiuguorui1 <qiuguorui1@huawei.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Cc: stable@vger.kernel.org # v4.18+ Link: https://lore.kernel.org/r/20200820031629.15582-1-qiuguorui1@huawei.com
| * | | irqchip: Revert modular support for drivers using IRQCHIP_PLATFORM_DRIVER ↵Marc Zyngier2020-08-254-14/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | helperse It has become obvious that switching a number of irqchip drivers to being platform drivers without considering the platform was a mistake. We have multiple reports of end-point drivers not probing because the irqchip driver isn't there yet, breaking the expectations of the users. This patch reverts: 920ecb8c35cb ("irqchip/mtk-cirq: Convert to a platform driver") f97dbf48ca43 ("irqchip/mtk-sysirq: Convert to a platform driver") 5be57099d445 ("irqchip/qcom-pdc: Switch to using IRQCHIP_PLATFORM_DRIVER helper macros") 95bf9305d2e3 ("irqchip/qcom-pdc: Allow QCOM_PDC to be loadable as a permanent module") and leave QCOM PDC, MTK sysrq and cirq drivers as built-in, special purpose drivers for the time being until we have worked out a better solution. Reported-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Reported-by: Frank Wunderlich <linux@fw-web.de> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/93debe6a0308b66d3f307af67ba7ec2c@kernel.org
| * | | irqchip: Fix probing deferal when using IRQCHIP_PLATFORM_DRIVER helpersMarc Zyngier2020-08-171-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When probing an interrupt controller that is behind a parent, we try to check whether the parent domain is available as an indication that we can actually try to probe. Unfortunately, we are checking this with the firmware node of the about to be probed device, not the parent. This is obviously bound to fail. Instead, use the parent node. Fixes: f8410e626569 ("irqchip: Add IRQCHIP_PLATFORM_DRIVER_BEGIN/END and IRQCHIP_MATCH helper macros") Reported-by: John Stultz <john.stultz@linaro.org> Tested-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Marc Zyngier <maz@kernel.org>
| * | | irqchip/ti-sci-inta: Add support for INTA directly connecting to GICLokesh Vutla2020-08-161-13/+74
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Driver assumes that Interrupt parent to Interrupt Aggregator is always Interrupt router. This is not true always and GIC can be a parent to Interrupt Aggregator. Update the driver to detect the parent and request the parent irqs accordingly. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20200806074826.24607-11-lokeshvutla@ti.com
| * | | irqchip/ti-sci-inta: Do not store TISCI device id in platform device id fieldLokesh Vutla2020-08-161-7/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Even though DT doesn't make active use of id field in platform_device, we cannot hijack it to store TISCI device id. So create a field in struct ti_sci_inta for storing TISCI id and drop usage of id field in platform_device. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20200806074826.24607-10-lokeshvutla@ti.com
| * | | irqchip/ti-sci-intr: Add support for INTR being a parent to INTRLokesh Vutla2020-08-161-59/+93
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Driver assumes that Interrupt parent to Interrupt router is always GIC. This is not true always and an Interrupt Router can be a parent to Interrupt Router. Update the driver to detect the parent and request the parent irqs accordingly. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20200806074826.24607-7-lokeshvutla@ti.com
| * | | firmware: ti_sci: Add support for getting resource with subtypeLokesh Vutla2020-08-161-22/+67
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | With SYSFW ABI 3.0 changes, interrupts coming out of an interrupt controller is identified by a type and it is consistent across SoCs. Similarly global events for Interrupt aggregator. So add an API to get resource range using a resource type. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Acked-by: Nishanth Menon <nm@ti.com> Link: https://lore.kernel.org/r/20200806074826.24607-4-lokeshvutla@ti.com
| * | | firmware: ti_sci: Drop unused structure ti_sci_rm_type_mapLokesh Vutla2020-08-161-55/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | struct ti_sci_rm_type_map is no longer used. Drop its definition and its declarations. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Acked-by: Nishanth Menon <nm@ti.com> Link: https://lore.kernel.org/r/20200806074826.24607-3-lokeshvutla@ti.com
| * | | firmware: ti_sci: Drop the device id to resource type translationLokesh Vutla2020-08-161-11/+1
| |/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | With ABI 3.0, sysfw deprecated special resource types used for AM65x SoC. Instead started using device id as resource type similar to the convention used in J721E SOC. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Acked-by: Nishanth Menon <nm@ti.com> Link: https://lore.kernel.org/r/20200806074826.24607-2-lokeshvutla@ti.com
* | | Merge tag 'locking-urgent-2020-08-30' of ↵Linus Torvalds2020-08-302-21/+14
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull locking fixes from Thomas Gleixner: "A set of fixes for lockdep, tracing and RCU: - Prevent recursion by using raw_cpu_* operations - Fixup the interrupt state in the cpu idle code to be consistent - Push rcu_idle_enter/exit() invocations deeper into the idle path so that the lock operations are inside the RCU watching sections - Move trace_cpu_idle() into generic code so it's called before RCU goes idle. - Handle raw_local_irq* vs. local_irq* operations correctly - Move the tracepoints out from under the lockdep recursion handling which turned out to be fragile and inconsistent" * tag 'locking-urgent-2020-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: lockdep,trace: Expose tracepoints lockdep: Only trace IRQ edges mips: Implement arch_irqs_disabled() arm64: Implement arch_irqs_disabled() nds32: Implement arch_irqs_disabled() locking/lockdep: Cleanup x86/entry: Remove unused THUNKs cpuidle: Move trace_cpu_idle() into generic code cpuidle: Make CPUIDLE_FLAG_TLB_FLUSHED generic sched,idle,rcu: Push rcu_idle deeper into the idle path cpuidle: Fixup IRQ state lockdep: Use raw_cpu_*() for per-cpu variables
| * | | cpuidle: Make CPUIDLE_FLAG_TLB_FLUSHED genericPeter Zijlstra2020-08-262-16/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This allows moving the leave_mm() call into generic code before rcu_idle_enter(). Gets rid of more trace_*_rcuidle() users. Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Tested-by: Marco Elver <elver@google.com> Link: https://lkml.kernel.org/r/20200821085348.369441600@infradead.org
| * | | sched,idle,rcu: Push rcu_idle deeper into the idle pathPeter Zijlstra2020-08-261-4/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Lots of things take locks, due to a wee bug, rcu_lockdep didn't notice that the locking tracepoints were using RCU. Push rcu_idle_{enter,exit}() as deep as possible into the idle paths, this also resolves a lot of _rcuidle()/RCU_NONIDLE() usage. Specifically, sched_clock_idle_wakeup_event() will use ktime which will use seqlocks which will tickle lockdep, and stop_critical_timings() uses lock. Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Tested-by: Marco Elver <elver@google.com> Link: https://lkml.kernel.org/r/20200821085348.310943801@infradead.org
| * | | cpuidle: Fixup IRQ statePeter Zijlstra2020-08-261-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Match the pattern elsewhere in this file. Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Tested-by: Marco Elver <elver@google.com> Link: https://lkml.kernel.org/r/20200821085348.251340558@infradead.org
* | | | Merge tag 'powerpc-5.9-4' of ↵Linus Torvalds2020-08-301-0/+2
|\ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux Pull powerpc fixes from Michael Ellerman: - Revert our removal of PROT_SAO, at least one user expressed an interest in using it on Power9. Instead don't allow it to be used in guests unless enabled explicitly at compile time. - A fix for a crash introduced by a recent change to FP handling. - Revert a change to our idle code that left Power10 with no idle support. - One minor fix for the new scv system call path to set PPR. - Fix a crash in our "generic" PMU if branch stack events were enabled. - A fix for the IMC PMU, to correctly identify host kernel samples. - The ADB_PMU powermac code was found to be incompatible with VMAP_STACK, so make them incompatible in Kconfig until the code can be fixed. - A build fix in drivers/video/fbdev/controlfb.c, and a documentation fix. Thanks to Alexey Kardashevskiy, Athira Rajeev, Christophe Leroy, Giuseppe Sacco, Madhavan Srinivasan, Milton Miller, Nicholas Piggin, Pratik Rajesh Sampat, Randy Dunlap, Shawn Anastasio, Vaidyanathan Srinivasan. * tag 'powerpc-5.9-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: powerpc/32s: Disable VMAP stack which CONFIG_ADB_PMU Revert "powerpc/powernv/idle: Replace CPU feature check with PVR check" powerpc/perf: Fix reading of MSR[HV/PR] bits in trace-imc powerpc/perf: Fix crashes with generic_compat_pmu & BHRB powerpc/64s: Fix crash in load_fp_state() due to fpexc_mode powerpc/64s: scv entry should set PPR Documentation/powerpc: fix malformed table in syscall64-abi video: fbdev: controlfb: Fix build for COMPILE_TEST=y && PPC_PMAC=n selftests/powerpc: Update PROT_SAO test to skip ISA 3.1 powerpc/64s: Disallow PROT_SAO in LPARs by default Revert "powerpc/64s: Remove PROT_SAO support"
| * | | | video: fbdev: controlfb: Fix build for COMPILE_TEST=y && PPC_PMAC=nMichael Ellerman2020-08-271-0/+2
| | |/ / | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The build is currently broken, if COMPILE_TEST=y and PPC_PMAC=n: linux/drivers/video/fbdev/controlfb.c: In function ‘control_set_hardware’: linux/drivers/video/fbdev/controlfb.c:276:2: error: implicit declaration of function ‘btext_update_display’ 276 | btext_update_display(p->frame_buffer_phys + CTRLFB_OFF, | ^~~~~~~~~~~~~~~~~~~~ Fix it by including btext.h whenever CONFIG_BOOTX_TEXT is enabled. Fixes: a07a63b0e24d ("video: fbdev: controlfb: add COMPILE_TEST support") Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Link: https://lore.kernel.org/r/20200821104910.3363818-1-mpe@ellerman.id.au
* | | | Merge tag 'usb-5.9-rc3' of ↵Linus Torvalds2020-08-3024-161/+376
|\ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb Pull USB fixes from Greg KH: "Let's try this again... Here are some USB fixes for 5.9-rc3. This differs from the previous pull request for this release in that the usb gadget patch now does not break some systems, and actually does what it was intended to do. Many thanks to Marek Szyprowski for quickly noticing and testing the patch from Andy Shevchenko to resolve this issue. Additionally, some more new USB quirks have been added to get some new devices to work properly based on user reports. Other than that, the patches are all here, and they contain: - usb gadget driver fixes - xhci driver fixes - typec fixes - new quirks and ids - fixes for USB patches that went into 5.9-rc1. All of these have been tested in linux-next with no reported issues" * tag 'usb-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits) usb: storage: Add unusual_uas entry for Sony PSZ drives USB: Ignore UAS for JMicron JMS567 ATA/ATAPI Bridge usb: host: ohci-exynos: Fix error handling in exynos_ohci_probe() USB: gadget: u_f: Unbreak offset calculation in VLAs USB: quirks: Ignore duplicate endpoint on Sound Devices MixPre-D usb: typec: tcpm: Fix Fix source hard reset response for TDA 2.3.1.1 and TDA 2.3.1.2 failures USB: PHY: JZ4770: Fix static checker warning. USB: gadget: f_ncm: add bounds checks to ncm_unwrap_ntb() USB: gadget: u_f: add overflow checks to VLA macros xhci: Always restore EP_SOFT_CLEAR_TOGGLE even if ep reset failed xhci: Do warm-reset when both CAS and XDEV_RESUME are set usb: host: xhci: fix ep context print mismatch in debugfs usb: uas: Add quirk for PNY Pro Elite tools: usb: move to tools buildsystem USB: Fix device driver race USB: Also match device drivers using the ->match vfunc usb: host: xhci-tegra: fix tegra_xusb_get_phy() usb: host: xhci-tegra: otg usb2/usb3 port init usb: hcd: Fix use after free in usb_hcd_pci_remove() usb: typec: ucsi: Hold con->lock for the entire duration of ucsi_register_port() ...
| * | | | usb: storage: Add unusual_uas entry for Sony PSZ drivesAlan Stern2020-08-281-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The PSZ-HA* family of USB disk drives from Sony can't handle the REPORT OPCODES command when using the UAS protocol. This patch adds an appropriate quirks entry. Reported-and-tested-by: Till Dörges <doerges@pre-sense.de> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200826143229.GB400430@rowland.harvard.edu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | | USB: Ignore UAS for JMicron JMS567 ATA/ATAPI BridgeCyril Roelandt2020-08-271-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This device does not support UAS properly and a similar entry already exists in drivers/usb/storage/unusual_uas.h. Without this patch, storage_probe() defers the handling of this device to UAS, which cannot handle it either. Tested-by: Brice Goglin <brice.goglin@gmail.com> Fixes: bc3bdb12bbb3 ("usb-storage: Disable UAS on JMicron SATA enclosure") Acked-by: Alan Stern <stern@rowland.harvard.edu> CC: <stable@vger.kernel.org> Signed-off-by: Cyril Roelandt <tipecaml@gmail.com> Link: https://lore.kernel.org/r/20200825212231.46309-1-tipecaml@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | | usb: host: ohci-exynos: Fix error handling in exynos_ohci_probe()Tang Bin2020-08-271-3/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If the function platform_get_irq() failed, the negative value returned will not be detected here. So fix error handling in exynos_ohci_probe(). And when get irq failed, the function platform_get_irq() logs an error message, so remove redundant message here. Fixes: 62194244cf87 ("USB: Add Samsung Exynos OHCI diver") Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> Link: https://lore.kernel.org/r/20200826144931.1828-1-tangbin@cmss.chinamobile.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | | USB: gadget: u_f: Unbreak offset calculation in VLAsAndy Shevchenko2020-08-271-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Inadvertently the commit b1cd1b65afba ("USB: gadget: u_f: add overflow checks to VLA macros") makes VLA macros to always return 0 due to different scope of two variables of the same name. Obviously we need to have only one. Fixes: b1cd1b65afba ("USB: gadget: u_f: add overflow checks to VLA macros") Reported-by: Marek Szyprowski <m.szyprowski@samsung.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Brooke Basile <brookebasile@gmail.com> Cc: stable <stable@kernel.org> Link: https://lore.kernel.org/r/20200826192119.56450-1-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | | USB: quirks: Ignore duplicate endpoint on Sound Devices MixPre-DAlan Stern2020-08-271-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Sound Devices MixPre-D audio card suffers from the same defect as the Sound Devices USBPre2: an endpoint shared between a normal audio interface and a vendor-specific interface, in violation of the USB spec. Since the USB core now treats duplicated endpoints as bugs and ignores them, the audio endpoint isn't available and the card can't be used for audio capture. Along the same lines as commit bdd1b147b802 ("USB: quirks: blacklist duplicate ep on Sound Devices USBPre2"), this patch adds a quirks entry saying to ignore ep5in for interface 1, leaving it available for use with standard audio interface 2. Reported-and-tested-by: Jean-Christophe Barnoud <jcbarnoud@gmail.com> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: <stable@vger.kernel.org> Fixes: 3e4f8e21c4f2 ("USB: core: fix check for duplicate endpoints") Link: https://lore.kernel.org/r/20200826194624.GA412633@rowland.harvard.edu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | | usb: typec: tcpm: Fix Fix source hard reset response for TDA 2.3.1.1 and TDA ↵Badhri Jagan Sridharan2020-08-251-3/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 2.3.1.2 failures The patch addresses the compliance test failures while running TDA 2.3.1.1 and TDA 2.3.1.2 of the "PD Communications Engine USB PD Compliance MOI" test plan published in https://www.usb.org/usbc. For a product to be Type-C compliant, it's expected that these tests are run on usb.org certified Type-C compliance tester as mentioned in https://www.usb.org/usbc. While the purpose of TDA 2.3.1.1 and TDA 2.3.1.2 is to verify that the static and dynamic electrical capabilities of a Source meet the requirements for each PDO offered, while doing so, the tests also monitor that the timing of the VBUS waveform versus the messages meets the requirements for Hard Reset defined in PROT-PROC-HR-TSTR as mentioned in step 11 of TDA.2.3.1.1 and step 15 of TDA.2.3.1.2. TDB.2.2.13.1: PROT-PROC-HR-TSTR Procedure and Checks for Tester Originated Hard Reset Purpose: To perform the appropriate protocol checks relating to any circumstance in which the Hard Reset signal is sent by the Tester. UUT is behaving as source: The Tester sends a Hard Reset signal. 1. Check VBUS stays within present valid voltage range for tPSHardReset min (25ms) after last bit of Hard Reset signal. [PROT_PROC_HR_TSTR_1] 2. Check that VBUS starts to fall below present valid voltage range by tPSHardReset max (35ms). [PROT_PROC_HR_TSTR_2] 3. Check that VBUS reaches vSafe0V within tSafe0v max (650 ms). [PROT_PROC_HR_TSTR_3] 4. Check that VBUS starts rising to vSafe5V after a delay of tSrcRecover (0.66s - 1s) from reaching vSafe0V. [PROT_PROC_HR_TSTR_4] 5. Check that VBUS reaches vSafe5V within tSrcTurnOn max (275ms) of rising above vSafe0v max (0.8V). [PROT_PROC_HR_TSTR_5] Power Delivery Compliance Plan 139 6. Check that Source Capabilities are finished sending within tFirstSourceCap max (250ms) of VBUS reaching vSafe5v min. [PROT_PROC_HR_TSTR_6]. This is in line with 7.1.5 Response to Hard Resets of the USB Power Delivery Specification Revision 3.0, Version 1.2, "Hard Reset Signaling indicates a communication failure has occurred and the Source Shall stop driving VCONN, Shall remove Rp from the VCONN pin and Shall drive VBUS to vSafe0V as shown in Figure 7-9. The USB connection May reset during a Hard Reset since the VBUS voltage will be less than vSafe5V for an extended period of time. After establishing the vSafe0V voltage condition on VBUS, the Source Shall wait tSrcRecover before re-applying VCONN and restoring VBUS to vSafe5V. A Source Shall conform to the VCONN timing as specified in [USB Type-C 1.3]." With the above guidelines from the spec in mind, TCPM does not turn off VCONN while entering SRC_HARD_RESET_VBUS_OFF. The patch makes TCPM turn off VCONN while entering SRC_HARD_RESET_VBUS_OFF and turn it back on while entering SRC_HARD_RESET_VBUS_ON along with vbus instead of having VCONN on through hardreset. Also, the spec clearly states that "After establishing the vSafe0V voltage condition on VBUS", the Source Shall wait tSrcRecover before re-applying VCONN and restoring VBUS to vSafe5V. TCPM does not conform to this requirement. If the TCPC driver calls tcpm_vbus_change with vbus off signal, TCPM right away enters SRC_HARD_RESET_VBUS_ON without waiting for tSrcRecover. For TCPC's which are buggy/does not call tcpm_vbus_change, TCPM assumes that the vsafe0v is instantaneous as TCPM only waits tSrcRecover instead of waiting for tSafe0v + tSrcRecover. This patch also fixes this behavior by making sure that TCPM waits for tSrcRecover before transitioning into SRC_HARD_RESET_VBUS_ON when tcpm_vbus_change is called by TCPC. When TCPC does not call tcpm_vbus_change, TCPM assumes the worst case i.e. tSafe0v + tSrcRecover before transitioning into SRC_HARD_RESET_VBUS_ON. Signed-off-by: Badhri Jagan Sridharan <badhri@google.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Cc: stable <stable@kernel.org> Link: https://lore.kernel.org/r/20200817184601.1899929-1-badhri@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | | USB: PHY: JZ4770: Fix static checker warning.周琰杰 (Zhou Yanjie)2020-08-251-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The commit 2a6c0b82e651 ("USB: PHY: JZ4770: Add support for new Ingenic SoCs.") introduced the initialization function for different chips, but left the relevant code involved in the resetting process in the original function, resulting in uninitialized variable calls. Fixes: 2a6c0b82e651 ("USB: PHY: JZ4770: Add support for new Ingenic SoCs."). Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com> Link: https://lore.kernel.org/r/20200825081654.18186-2-zhouyanjie@wanyeetech.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | | USB: gadget: f_ncm: add bounds checks to ncm_unwrap_ntb()Brooke Basile2020-08-251-12/+69
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some values extracted by ncm_unwrap_ntb() could possibly lead to several different out of bounds reads of memory. Specifically the values passed to netdev_alloc_skb_ip_align() need to be checked so that memory is not overflowed. Resolve this by applying bounds checking to a number of different indexes and lengths of the structure parsing logic. Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com> Signed-off-by: Brooke Basile <brookebasile@gmail.com> Acked-by: Felipe Balbi <balbi@kernel.org> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit (git 2.34.1) at 2025-02-24 21:03:41 +0000