aboutsummaryrefslogtreecommitdiffstats
path: root/drivers
Commit message (Collapse)AuthorAgeFilesLines
* drm/gma500: Drop dev->struct_mutex from modeset codeDaniel Vetter2015-12-011-10/+3
| | | | | | | | | | | | | | | It's either init code or already protected by other means. Note that psb_gtt_pin/unpin has it's own lock, and that's really the only piece of driver private state - all the modeset state is protected with modeset locks already. The only important bit is to switch all gem_obj_unref calls to the _unlocked variant. Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com> Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/1448271183-20523-18-git-send-email-daniel.vetter@ffwll.ch
* drm/gma500: Use correct unref in the gem bo create functionDaniel Vetter2015-12-011-1/+1
| | | | | | | | | | | | | This is called without dev->struct_mutex held, we need to use the _unlocked variant. Never caught in the wild since you'd need an evil userspace which races a gem_close ioctl call with the in-progress open. Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com> Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/1448271183-20523-17-git-send-email-daniel.vetter@ffwll.ch
* drm/edid: Make the detailed timing CEA/HDMI mode fixup accept up to 5kHz ↵Ville Syrjälä2015-12-012-3/+78
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | clock difference Rather than using drm_match_cea_mode() to see if the EDID detailed timings are supposed to represent one of the CEA/HDMI modes, add a special version of that function that takes in an explicit clock tolerance value (in kHz). When looking at the detailed timings specify the tolerance as 5kHz due to the 10kHz clock resolution limit inherent in detailed timings. drm_match_cea_mode() uses the normal KHZ2PICOS() matching of clocks, which only allows smaller errors for lower clocks (eg. for 25200 it won't allow any error) and a bigger error for higher clocks (eg. for 297000 it actually matches 296913-297000). So it doesn't really match what we want for the fixup. Using the explicit +-5kHz is much better for this use case. Not sure if we should change the normal mode matching to also use something else besides KHZ2PICOS() since it allows a different proportion of error depending on the clock. I believe VESA CVT allows a maximum deviation of .5%, so using that for normal mode matching might be a good idea? Cc: Adam Jackson <ajax@redhat.com> Tested-by: nathan.d.ciobanu@linux.intel.com Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92217 Fixes: fa3a7340eaa1 ("drm/edid: Fix up clock for CEA/HDMI modes specified via detailed timings") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Adam Jackson <ajax@redhat.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
* drm/atomic_helper: Add drm_atomic_helper_disable_planes_on_crtc()Jyri Sarha2015-11-301-0/+43
| | | | | | | | | | | | | | | | | | | | Add drm_atomic_helper_disable_planes_on_crtc() for disabling all planes associated with the given CRTC. This can be used for instance in the CRTC helper disable callback to disable all planes before shutting down the display pipeline. v2: - Address Daniels review comments [1] - Do atomic_begin() and atomic_flush() always if they are defined and atomic knob is set - update kerneldoc - Put drm_atomic_helper_disable_planes_on_crtc() after drm_atomic_helper_commit_planes_on_crtc() in drm_atomic_helper.c to have functions in the same order as in drm_atomic_helper.h Signed-off-by: Jyri Sarha <jsarha@ti.com> Link: http://patchwork.freedesktop.org/patch/msgid/1448633641-6486-1-git-send-email-jsarha@ti.com Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
* drm: Serialise multiple event readersChris Wilson2015-11-261-5/+13
| | | | | | | | | | | | | | | | | The previous patch reintroduced a race condition whereby a failure in one reader may allow a second reader to see out-of-order events. Introduce a mutex to serialise readers so that an event is completed in its entirety before another reader may process an event. The two readers may race against each other, but the events each retrieves are in the correct order. Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Thomas Hellstrom <thellstrom@vmware.com> Cc: Takashi Iwai <tiwai@suse.de> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/1448462343-2072-2-git-send-email-chris@chris-wilson.co.uk Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
* drm: Drop dev->event_lock spinlock around faulting copy_to_user()Chris Wilson2015-11-261-16/+24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | In commit cdd1cf799bd24ac0a4184549601ae302267301c5 Author: Chris Wilson <chris@chris-wilson.co.uk> Date: Thu Dec 4 21:03:25 2014 +0000 drm: Make drm_read() more robust against multithreaded races I fixed the races by serialising the use of the event by extending the dev->event_lock. However, as Thomas pointed out, the copy_to_user() may fault (even the __copy_to_user_inatomic() variant used here) and calling into the driver backend with the spinlock held is bad news. Therefore we have to drop the spinlock before the copy, but that exposes us to the old race whereby a second reader could see an out-of-order event (as the first reader may claim the first request but fail to copy it back to userspace and so on returning it to the event list it will be behind the current event being copied by the second reader). Reported-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Thomas Hellstrom <thellstrom@vmware.com> Cc: Takashi Iwai <tiwai@suse.de> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/1448462343-2072-1-git-send-email-chris@chris-wilson.co.uk Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
* drm/i915: fix potential dangling else problems in for_each_ macrosJani Nikula2015-11-254-10/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We have serious dangling else bugs waiting to happen in our for_each_ style macros with ifs. Consider, for example, #define for_each_power_domain(domain, mask) \ for ((domain) = 0; (domain) < POWER_DOMAIN_NUM; (domain)++) \ if ((1 << (domain)) & (mask)) If this is used in context: if (condition) for_each_power_domain(domain, mask); else foo(); foo() will be called for each domain *not* in mask, if condition holds, and not at all if condition doesn't hold. Fix this by reversing the conditions in the macros, and adding an else branch for the "for each" block, so that other if/else blocks can't interfere. Provide a "for_each_if" helper macro to make it easier to get this right. v2: move for_each_if to drmP.h in a separate patch. Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1448392916-2281-2-git-send-email-jani.nikula@intel.com Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
* drm/sysfs: Send out uevent when connector->force changesDaniel Vetter2015-11-242-48/+36
| | | | | | | | | | | | | | | | | | | | | | To avoid even more code duplication punt this all to the probe worker, which needs some slight adjustment to also generate a uevent when the status has changed to due connector->force. v2: Instead of running the output_poll_work (which is kinda the wrong thing and a layering violation since it's an internal of the probe helpers), or calling ->detect (which is again a layering violation since it's used only by probe helpers) just call the official ->fill_modes function, like a GET_CONNECTOR ioctl call. v3: Restore the accidentally removed forced-probe for echo "detect" > force. Cc: Chris Wilson <chris@chris-wilson.co.uk> Reported-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1447951610-12622-22-git-send-email-daniel.vetter@ffwll.ch Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
* drm/atomic: Small documentation fix.Maarten Lankhorst2015-11-241-1/+1
| | | | | | | Use the correct function name for drm_atomic_clean_old_fb docs. Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
* drm/sysfs: Grab lock for edid/modes_showDaniel Vetter2015-11-241-4/+12
| | | | | | | | | | | | | | | | | We chase pointers/lists without taking the locks protecting them, which isn't that good. Fix it. v2: Actually unlock properly, spotted by Julia. v3: Put the label _before_ the mutex_unlock (Emil) Cc: Emil Velikov <emil.l.velikov@gmail.com> Cc: Julia Lawall <julia.lawall@lip6.fr> Link: http://patchwork.freedesktop.org/patch/msgid/1443783662-23066-1-git-send-email-daniel.vetter@ffwll.ch Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
* drm: Print the src/dst/clip rectangles in error in drm_plane_helperVille Syrjälä2015-11-241-0/+4
| | | | | | | | To aid in debugging failures, print the src,dst,clip rectangles when drm_plane_helper_check_update() fails. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
* drm: Add "prefix" parameter to drm_rect_debug_print()Ville Syrjälä2015-11-242-7/+8
| | | | | | | | Allow the caller to specify a "prefix" string to drm_rect_debug_print() to make it easier to see which drm_rect is being printed. Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
* drm: Keep coordinates in the typical x, y, w, h order instead of x, y, h, wVille Syrjälä2015-11-241-7/+7
| | | | | | Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
* drm: Pass the user drm_mode_fb_cmd2 as const to .fb_create()Ville Syrjälä2015-11-2447-71/+71
| | | | | | | | | | Drivers shouldn't clobber the passed in addfb ioctl parameters. i915 was doing just that. To prevent it from happening again, pass the struct around as const, starting all the way from internal_framebuffer_create(). Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
* drm: modes: replace simple_strtoul by kstrtouintLABBE Corentin2015-11-241-5/+11
| | | | | | | | The simple_strtoul function is marked as obsolete. This patch replace it by kstrtouint. Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
* drm: Remove unused fbdev_list membersLukas Wunner2015-11-249-10/+0
| | | | | | | | | | | | | | | | | | | | I noticed that intel_fbdev->our_mode is unused. Introduced by 79e539453b34 ("DRM: i915: add mode setting support"). Then I noticed that intel_fbdev->fbdev_list is unused as well. Introduced by 386516744ba4 ("drm/fb: fix fbdev object model + cleanup properly.") in i915, nouveau and radeon. Subsequently cargo culted to amdgpu, ast, cirrus, qxl, udl, virtio and mgag200. Already removed from the latter with cc59487a05b1 ("drm/mgag200: 'fbdev_list' in 'struct mga_fbdev' is not used"). Remove it from the others. Signed-off-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
* GPU-DRM: Delete unnecessary checks before drm_property_unreference_blob()Markus Elfring2015-11-242-9/+5
| | | | | | | | | | | | The drm_property_unreference_blob() function tests whether its argument is NULL and then returns immediately. Thus the tests around the calls are not needed. This issue was detected by using the Coccinelle software. Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Link: http://patchwork.freedesktop.org/patch/msgid/563C8B3E.405@users.sourceforge.net Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
* drm/tegra: Remove local fbdev emulation Kconfig optionArchit Taneja2015-11-244-23/+11
| | | | | | | | | | | | DRM_TEGRA_FBDEV config is currently used to enable/disable legacy fbdev emulation for the tegra kms driver. Remove this local config option and use the top level DRM_FBDEV_EMULATION config option instead. Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/1445933459-5249-4-git-send-email-architt@codeaurora.org Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
* drm/imx: Remove local fbdev emulation Kconfig optionArchit Taneja2015-11-242-18/+3
| | | | | | | | | | | | | | DRM_IMX_FB_HELPER config is currently used to enable/disable fbdev emulation for the imx kms driver. Remove this local config option and use the top level DRM_FBDEV_EMULATION config option where applicable. Using this config lets us also prevent wrapping around drm_fb_helper_* calls with #ifdefs in certain places. Tested-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/1445933459-5249-2-git-send-email-architt@codeaurora.org Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
* drm/gem: Update/Polish docsDaniel Vetter2015-11-241-3/+32
| | | | | | | | | | | A bunch of things have been removed meanwhile and docs not fully brought up to speed. And a few gaps closed where I noticed missing kerneldoc while reading through the overview sections. Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1445533889-7661-3-git-send-email-daniel.vetter@ffwll.ch Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
* Merge tag 'tty-4.4-rc2' of ↵Linus Torvalds2015-11-2210-10/+12
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty Pull tty/serial fixes from Greg KH: "Here are a few small tty/serial driver fixes for 4.4-rc2 that resolve some reported problems. All have been in linux-next, full details are in the shortlog below" * tag 'tty-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: serial: export fsl8250_handle_irq serial: 8250_mid: Add missing dependency tty: audit: Fix audit source serial: etraxfs-uart: Fix crash serial: fsl_lpuart: Fix earlycon support bcm63xx_uart: Use the device name when registering an interrupt tty: Fix direct use of tty buffer work tty: Fix tty_send_xchar() lock order inversion
| * serial: export fsl8250_handle_irqArnd Bergmann2015-11-201-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | fsl8250_handle_irq is now used by the of_serial driver, and that fails if it is a loadable module: ERROR: "fsl8250_handle_irq" [drivers/tty/serial/of_serial.ko] undefined! This exports the symbol to avoid randconfig errors. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: d43b54d269d2 ("serial: Enable Freescale 16550 workaround on arm") Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * serial: 8250_mid: Add missing dependencyHeikki Krogerus2015-11-201-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 8250_mid uses rational_best_approximation() function, so the driver needs to select CONFIG_RATIONAL option. This fixes build error when CONFIG_RATIONAL is not enabled: drivers/built-in.o: In function `mid8250_set_termios': 8250_mid.c:(.text+0x10169a): undefined reference to `rational_best_approximation' Reported-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * tty: audit: Fix audit sourcePeter Hurley2015-11-202-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | The data to audit/record is in the 'from' buffer (ie., the input read buffer). Fixes: 72586c6061ab ("n_tty: Fix auditing support for cannonical mode") Cc: stable <stable@vger.kernel.org> # 4.1+ Cc: Miloslav Trmač <mitr@redhat.com> Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Acked-by: Laura Abbott <labbott@fedoraproject.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * serial: etraxfs-uart: Fix crashGuenter Roeck2015-11-201-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since commit 7d8c70d8048c ("serial: mctrl-gpio: rename init function"), crisv32 either do not build or crash as follows. Unable to handle kernel NULL pointer dereference Linux 4.3.0-rc7-next-20151101 #1 Sun Nov 1 11:41:28 PST 2015 ... Call Trace: [<c0004a0e>] show_stack+0x0/0x9e [<c004c0c0>] printk+0x0/0x2c [<c00059d4>] show_registers+0x14a/0x1c2 [<c004c0c0>] printk+0x0/0x2c [<c0004b52>] die_if_kernel+0x7c/0x9e [<c0005346>] do_page_fault+0x32e/0x3e6 [<c01dc59c>] of_get_property+0x0/0x2c [<c01e0558>] of_irq_parse_raw+0x12a/0x376 [<c01dc59c>] of_get_property+0x0/0x2c [<c0053aca>] get_page_from_freelist+0x73e/0x856 [<c01dc59c>] of_get_property+0x0/0x2c [<c0008912>] d_mmu_refill+0x10a/0x112 [<c01b488c>] devm_kmalloc+0x40/0x56 [<c01b47d0>] add_dr+0xc/0x1c [<c01b4800>] devm_add_action+0x2/0x4e [<c01abdbc>] mctrl_gpio_init_noauto+0x1c/0x76 [<c01abf9e>] mctrl_gpio_init+0x22/0x110 The function call in the etraxfs-uart driver was not renamed, possibly due to interference with commit 7b9c5162c182 ("serial: etraxfs-uart: use mctrl_gpio helpers for handling modem signals"). Fixes: 7d8c70d8048c ("serial: mctrl-gpio: rename init function") Signed-off-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Niklas Cassel <nks@flawful.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * serial: fsl_lpuart: Fix earlycon supportPeter Hurley2015-11-201-1/+1
| | | | | | | | | | | | | | | | | | | | | | Earlycon support for Freescale lpuart should only be enabled when console support is enabled. Fixes: 1d59b382f1c4 ("serial: fsl_lpuart: add earlycon support") Acked-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * bcm63xx_uart: Use the device name when registering an interruptSimon Arlott2015-11-201-1/+1
| | | | | | | | | | | | | | | | Use the device name when registering an interrupt so that multiple ports don't all have the same interrupt name. Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * tty: Fix direct use of tty buffer workPeter Hurley2015-11-201-1/+1
| | | | | | | | | | | | | | | | | | Recent abstraction of tty buffer work introduced api to manage tty input kworker; use it. Fixes: e176058f0de5 ("tty: Abstract tty buffer work") Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * tty: Fix tty_send_xchar() lock order inversionPeter Hurley2015-11-202-4/+4
| | | | | | | | | | | | | | | | | | | | | | The correct lock order is atomic_write_lock => termios_rwsem, as established by tty_write() => n_tty_write(). Fixes: c274f6ef1c666 ("tty: Hold termios_rwsem for tcflow(TCIxxx)") Reported-and-Tested-by: Dmitry Vyukov <dvyukov@google.com> Cc: <stable@vger.kernel.org> # v3.18+ Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | Merge tag 'staging-4.4-rc2' of ↵Linus Torvalds2015-11-228-64/+115
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging Pull staging/IIO fixes from Greg KH: "Here are some staging and iio driver fixes for 4.4-rc2. All of these are in response to issues that have been reported and have been in linux-next for a while" * tag 'staging-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: Revert "Staging: wilc1000: coreconfigurator: Drop unneeded wrapper functions" iio: adc: xilinx: Fix VREFN scale iio: si7020: Swap data byte order iio: adc: vf610_adc: Fix division by zero error iio:ad7793: Fix ad7785 product ID iio: ad5064: Fix ad5629/ad5669 shift iio:ad5064: Make sure ad5064_i2c_write() returns 0 on success iio: lpc32xx_adc: fix warnings caused by enabling unprepared clock staging: iio: select IRQ_WORK for IIO_DUMMY_EVGEN vf610_adc: Fix internal temperature calculation
| * | Revert "Staging: wilc1000: coreconfigurator: Drop unneeded wrapper functions"Glen Lee2015-11-181-23/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The source and destination pointers are misplaced. This will be like, ether_addr_copy(data, bssid + ADDR2); -> ether_addr_copy(bssid, data + ADDR2); and also to use ether_addr_copy, it has to be proved that src/dst address are properly aligned(2). I revert this as author agree to drop this patch. This reverts commit d4622f68db8095dd54179e3134e97812727f6b89. Signed-off-by: Glen Lee <glen.lee@atmel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | Merge tag 'iio-fixes-for-4.4a' of ↵Greg Kroah-Hartman2015-11-187-41/+90
| |\ \ | | |/ | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ssh://ra.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus Jonathan writes: First set of IIO fixes for the 4.4 cycle. This set does not include those for issues introduced during the merge window. Fixes of those will follow in a future series. * ad5064 - Make sure the local i2c_write returns 0 on success rather than the number of bytes transfered. Otherwise we report an error on all writes. - Fix a shift for ad5629 and ad5669 which gives incorrect DAC output on these parts. * ad7793 - The product ID on the datasheet is wrong. Fix it in the driver. * IIO_DUMMY_EVGEN - select IRQ_WORK as a dependency. * lpc32xx - make sure clock is prepared before enabling. * si7020 - data byte order was reversed. Fix it. * vf610 - Internal temperature calculation was wrong if a different reference voltage was used. Now use a linear interpolation function to make it work over the full range. - Fix a division by zero in the case of a device tree property not being present (same issue two fixes). * xilinx XADC - VREFN scale was wrong - fix it.
| | * iio: adc: xilinx: Fix VREFN scaleThomas Betker2015-11-151-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The scaling factor for VREFN is 3.0/4096 (not 1.0/4096), just as for VREFP. This is not immediately obvious from the specification (Xilinx UG480), but has been confirmed by Xilinx support. Suggested-by: Hartmut Knaack <knaack.h@gmx.de> Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
| | * iio: si7020: Swap data byte orderChris Lesiak2015-11-151-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Silicon Labs Si7013, Si7020, and Si7021 family of I2C humidity and temperature sensors deliver 16 bit data high byte first. See the datasheet available at: https://www.silabs.com/Support%20Documents%2fTechnicalDocs%2fSi7020-A20.pdf But as documented in Documentation/i2c/smbus-protocol, i2c_smbus_read_word_data() expects the low byte first. Change the driver to use i2c_smbus_read_word_swapped to get correct byte order. Signed-off-by: Chris Lesiak <chris.lesiak@licor.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
| | * iio: adc: vf610_adc: Fix division by zero errorSanchayan Maity2015-11-081-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In case the fsl,adck-max-frequency property is not present in the device tree, a division by zero error results during the probe call on kernel boot (see below). This patch fixes it and also restores device tree compatibility in case kernels are booting with old device trees without this property specified. [ 1.063229] Division by zero in kernel. [ 1.067152] CPU: 0 PID: 1 Comm: swapper Not tainted 4.3.0-rc5-00212-gcc88cef #37 [ 1.074650] Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree) [ 1.081135] Backtrace: [ 1.083694] [<800134a4>] (dump_backtrace) from [<8001369c>] (show_stack+0x18/0x1c) [ 1.091340] r7:00000008 r6:8e0ae210 r5:00000000 r4:8e299800 [ 1.097146] [<80013684>] (show_stack) from [<80297b1c>] (dump_stack+0x24/0x28) [ 1.104483] [<80297af8>] (dump_stack) from [<80013608>] (__div0+0x1c/0x20) [ 1.111421] [<800135ec>] (__div0) from [<802968b4>] (Ldiv0+0x8/0x10) [ 1.117865] [<80424350>] (vf610_adc_probe) from [<803153b4>] (platform_drv_probe+0x4c/0xac) [ 1.126311] r10:00000000 r9:8076a5ec r8:00000000 r7:fffffdfb r6:807cc67c r5:8e0ae210 [ 1.134319] r4:807f6c54 [ 1.136915] [<80315368>] (platform_drv_probe) from [<803138bc>] (driver_probe_device+0x20c/0x2f8) [ 1.145882] r7:807cc67c r6:00000000 r5:8e0ae210 r4:807f6c54 [ 1.151657] [<803136b0>] (driver_probe_device) from [<80313a3c>] (__driver_attach+0x94/0x98) [ 1.160190] r9:8076a5ec r8:00000098 r7:00000000 r6:8e0ae244 r5:807cc67c r4:8e0ae210 [ 1.168112] [<803139a8>] (__driver_attach) from [<80311cb8>] (bus_for_each_dev+0x70/0xa4) [ 1.176383] r7:00000000 r6:803139a8 r5:807cc67c r4:00000000 [ 1.182159] [<80311c48>] (bus_for_each_dev) from [<80313318>] (driver_attach+0x24/0x28) [ 1.190260] r6:807bb568 r5:8e2a5b00 r4:807cc67c [ 1.194996] [<803132f4>] (driver_attach) from [<80312f50>] (bus_add_driver+0x1a4/0x21c) [ 1.203113] [<80312dac>] (bus_add_driver) from [<803142a8>] (driver_register+0x80/0x100) [ 1.211275] r7:8e2a7dc0 r6:807a8160 r5:80789e14 r4:807cc67c [ 1.217075] [<80314228>] (driver_register) from [<803152f8>] (__platform_driver_register+0x5c/0x64) [ 1.226216] r5:80789e14 r4:807a8160 [ 1.229877] [<8031529c>] (__platform_driver_register) from [<80789e30>] (vf610_adc_driver_init+0x1c/0x20) [ 1.239556] [<80789e14>] (vf610_adc_driver_init) from [<800095f8>] (do_one_initcall+0x94/0x1dc) [ 1.248365] [<80009564>] (do_one_initcall) from [<8076ae34>] (kernel_init_freeable+0x13c/0x1e0) [ 1.257155] r10:80794830 r9:8076a5ec r8:00000098 r7:807d5780 r6:807d5780 r5:00000006 [ 1.265153] r4:807a0ee8 [ 1.267753] [<8076acf8>] (kernel_init_freeable) from [<80590ef0>] (kernel_init+0x18/0xf0) [ 1.276021] r10:00000000 r9:00000000 r8:00000000 r7:00000000 r6:00000000 r5:80590ed8 [ 1.284015] r4:807d5780 [ 1.286615] [<80590ed8>] (kernel_init) from [<8000f878>] (ret_from_fork+0x14/0x3c) [ 1.294278] r5:80590ed8 r4:00000000 Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com> Acked-by: Fugang Duan <B38611@freescale.com> Acked-by: Stefan Agner <stefan@agner.ch> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
| | * iio:ad7793: Fix ad7785 product IDLars-Peter Clausen2015-10-251-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | While the datasheet for the AD7785 lists 0xXB as the product ID the actual product ID is 0xX3. Fix the product ID otherwise the driver will reject the device due to non matching IDs. Fixes: e786cc26dcc5 ("staging:iio:ad7793: Implement stricter id checking") Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
| | * iio: ad5064: Fix ad5629/ad5669 shiftLars-Peter Clausen2015-10-251-26/+57
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ad5629/ad5669 are the I2C variant of the ad5628/ad5668, which has a SPI interface. They are mostly identical with the exception that the shift factor is different. Currently the driver does not take care of this difference which leads to incorrect DAC output values. Fix this by introducing a custom channel spec for the ad5629/ad5669 with the correct shift factor. Fixes: commit 6a17a0768f77 ("iio:dac:ad5064: Add support for the ad5629r and ad5669r") Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
| | * iio:ad5064: Make sure ad5064_i2c_write() returns 0 on successMichael Hennerich2015-10-251-1/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | i2c_master_send() returns the number of bytes transferred on success while the ad5064 driver expects that the write() callback returns 0 on success. Fix that by translating any non negative return value of i2c_master_send() to 0. Fixes: commit 6a17a0768f77 ("iio:dac:ad5064: Add support for the ad5629r and ad5669r") Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
| | * iio: lpc32xx_adc: fix warnings caused by enabling unprepared clockVladimir Zapolskiy2015-10-251-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If common clock framework is configured, the driver generates a warning, which is fixed by this change: root@devkit3250:~# cat /sys/bus/iio/devices/iio\:device0/in_voltage0_raw ------------[ cut here ]------------ WARNING: CPU: 0 PID: 724 at drivers/clk/clk.c:727 clk_core_enable+0x2c/0xa4() Modules linked in: sc16is7xx snd_soc_uda1380 CPU: 0 PID: 724 Comm: cat Not tainted 4.3.0-rc2+ #198 Hardware name: LPC32XX SoC (Flattened Device Tree) Backtrace: [<>] (dump_backtrace) from [<>] (show_stack+0x18/0x1c) [<>] (show_stack) from [<>] (dump_stack+0x20/0x28) [<>] (dump_stack) from [<>] (warn_slowpath_common+0x90/0xb8) [<>] (warn_slowpath_common) from [<>] (warn_slowpath_null+0x24/0x2c) [<>] (warn_slowpath_null) from [<>] (clk_core_enable+0x2c/0xa4) [<>] (clk_core_enable) from [<>] (clk_enable+0x24/0x38) [<>] (clk_enable) from [<>] (lpc32xx_read_raw+0x38/0x80) [<>] (lpc32xx_read_raw) from [<>] (iio_read_channel_info+0x70/0x94) [<>] (iio_read_channel_info) from [<>] (dev_attr_show+0x28/0x4c) [<>] (dev_attr_show) from [<>] (sysfs_kf_seq_show+0x8c/0xf0) [<>] (sysfs_kf_seq_show) from [<>] (kernfs_seq_show+0x2c/0x30) [<>] (kernfs_seq_show) from [<>] (seq_read+0x1c8/0x440) [<>] (seq_read) from [<>] (kernfs_fop_read+0x38/0x170) [<>] (kernfs_fop_read) from [<>] (do_readv_writev+0x16c/0x238) [<>] (do_readv_writev) from [<>] (vfs_readv+0x50/0x58) [<>] (vfs_readv) from [<>] (default_file_splice_read+0x1a4/0x308) [<>] (default_file_splice_read) from [<>] (do_splice_to+0x78/0x84) [<>] (do_splice_to) from [<>] (splice_direct_to_actor+0xc8/0x1cc) [<>] (splice_direct_to_actor) from [<>] (do_splice_direct+0xa0/0xb8) [<>] (do_splice_direct) from [<>] (do_sendfile+0x1a8/0x30c) [<>] (do_sendfile) from [<>] (SyS_sendfile64+0x104/0x10c) [<>] (SyS_sendfile64) from [<>] (ret_fast_syscall+0x0/0x38) Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
| | * staging: iio: select IRQ_WORK for IIO_DUMMY_EVGENArnd Bergmann2015-10-251-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The iio dummy code was recently changed to use irq_work_queue, but that code is compiled into the kernel only if IRQ_WORK is set, so we can get a link error here: drivers/built-in.o: In function `iio_evgen_poke': (.text+0x208a04): undefined reference to `irq_work_queue' This changes the Kconfig file to match what other drivers do. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: fd2bb310ca3d ("Staging: iio: Move evgen interrupt generation to irq_work") Acked-by: Daniel Baluta <daniel.baluta@intel.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
| | * vf610_adc: Fix internal temperature calculationBhuvanchandra DV2015-10-251-5/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Calculate ADCR_VTEMP25 using VTEMP25 at VREFH_ADC 3V3. Existing calculations consider the typical values provided in datasheet. Those typical values are valid for VREFH_ADC at 3.0V. VTEMP25 is different for different VREFH_ADC voltages. With VREFH_ADC at 3.3V, voltage at 25°C is 0.699V. Hence update the VTEMP25 to 0.699V which gives ADCR@Temp25 as 867. Formula for finding ADCR@Temp25: ADCR@Temp25 = (ADCR@Vdd * V@TEMP25 * 10) / VDDconv ADCR@Vdd for 12-Bit ADC = 4095 VDDconv = VREFH_ADC * 10 VREFH_ADC@3.3V ADCR@Temp25 = (4095 * .699 * 10) / 33 ADCR@Temp25 ~= 867 | VREFH_ADC | V@TEMP25 | VDDconv | ADCR@Temp25 | | 3.0V | 0.696mV | 30 | 950 | | 3.3V | 0.699mV | 33 | 867 | Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com> Acked-by: Fugang Duan <B38611@freescale.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <jic23@kernel.org>
* | | Merge tag 'usb-4.4-rc2' of ↵Linus Torvalds2015-11-2224-106/+329
|\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb Pull USB fixes from Greg KH: "Here are a number of USB fixes and new device ids for 4.4-rc2. All have been in linux-next and the details are in the shortlog" * tag 'usb-4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (28 commits) usblp: do not set TASK_INTERRUPTIBLE before lock USB: MAINTAINERS: cxacru usb: kconfig: fix warning of select USB_OTG USB: option: add XS Stick W100-2 from 4G Systems xhci: Fix a race in usb2 LPM resume, blocking U3 for usb2 devices usb: xhci: fix checking ep busy for CFC xhci: Workaround to get Intel xHCI reset working more reliably usb: chipidea: imx: fix a possible NULL dereference usb: chipidea: usbmisc_imx: fix a possible NULL dereference usb: chipidea: otg: gadget module load and unload support usb: chipidea: debug: disable usb irq while role switch ARM: dts: imx27.dtsi: change the clock information for usb usb: chipidea: imx: refine clock operations to adapt for all platforms usb: gadget: atmel_usba_udc: Expose correct device speed usb: musb: enable usb_dma parameter usb: phy: phy-mxs-usb: fix a possible NULL dereference usb: dwc3: gadget: let us set lower max_speed usb: musb: fix tx fifo flush handling usb: gadget: f_loopback: fix the warning during the enumeration usb: dwc2: host: Fix remote wakeup when not in DWC2_L2 ...
| * | | usblp: do not set TASK_INTERRUPTIBLE before lockJiri Slaby2015-11-191-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It is not permitted to set task state before lock. usblp_wwait sets the state to TASK_INTERRUPTIBLE and calls mutex_lock_interruptible. Upon return from that function, the state will be TASK_RUNNING again. This is clearly a bug and a warning is generated with LOCKDEP too: WARNING: CPU: 1 PID: 5109 at kernel/sched/core.c:7404 __might_sleep+0x7d/0x90() do not call blocking ops when !TASK_RUNNING; state=1 set at [<ffffffffa0c588d0>] usblp_wwait+0xa0/0x310 [usblp] Modules linked in: ... CPU: 1 PID: 5109 Comm: captmon Tainted: G W 4.2.5-0.gef2823b-default #1 Hardware name: LENOVO 23252SG/23252SG, BIOS G2ET33WW (1.13 ) 07/24/2012 ffffffff81a4edce ffff880236ec7ba8 ffffffff81716651 0000000000000000 ffff880236ec7bf8 ffff880236ec7be8 ffffffff8106e146 0000000000000282 ffffffff81a50119 000000000000028b 0000000000000000 ffff8802dab7c508 Call Trace: ... [<ffffffff8106e1c6>] warn_slowpath_fmt+0x46/0x50 [<ffffffff8109a8bd>] __might_sleep+0x7d/0x90 [<ffffffff8171b20f>] mutex_lock_interruptible_nested+0x2f/0x4b0 [<ffffffffa0c588fc>] usblp_wwait+0xcc/0x310 [usblp] [<ffffffffa0c58bb2>] usblp_write+0x72/0x350 [usblp] [<ffffffff8121ed98>] __vfs_write+0x28/0xf0 ... Commit 7f477358e2384c54b190cc3b6ce28277050a041b (usblp: Implement the ENOSPC convention) moved the set prior locking. So move it back after the lock. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Fixes: 7f477358e2 ("usblp: Implement the ENOSPC convention") Acked-By: Pete Zaitcev <zaitcev@yahoo.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | usb: kconfig: fix warning of select USB_OTGPeter Chen2015-11-192-5/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When choose randconfig for kernel build, it reports below warning: "warning: (USB_OTG_FSM && FSL_USB2_OTG && USB_MV_OTG) selects USB_OTG which has unmet direct dependencies (USB_SUPPORT && USB && PM)" In fact, USB_OTG is visible symbol and depends on PM, so the driver needs to depend on it to reduce dependency problem. Signed-off-by: Peter Chen <peter.chen@freescale.com> Reported-by: Arnd Bergmann <arnd@arndb.de> Cc: Felipe Balbi <balbi@ti.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | USB: option: add XS Stick W100-2 from 4G SystemsBjørn Mork2015-11-191-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Thomas reports " 4gsystems sells two total different LTE-surfsticks under the same name. .. The newer version of XS Stick W100 is from "omega" .. Under windows the driver switches to the same ID, and uses MI03\6 for network and MI01\6 for modem. .. echo "1c9e 9b01" > /sys/bus/usb/drivers/qmi_wwan/new_id echo "1c9e 9b01" > /sys/bus/usb-serial/drivers/option1/new_id T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1c9e ProdID=9b01 Rev=02.32 S: Manufacturer=USB Modem S: Product=USB Modem S: SerialNumber= C: #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan I: If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage Now all important things are there: wwp0s29f7u2i3 (net), ttyUSB2 (at), cdc-wdm0 (qmi), ttyUSB1 (at) There is also ttyUSB0, but it is not usable, at least not for at. The device works well with qmi and ModemManager-NetworkManager. " Reported-by: Thomas Schäfer <tschaefer@t-online.de> Cc: <stable@vger.kernel.org> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
| * | | Merge tag 'usb-serial-4.4-rc2' of ↵Greg Kroah-Hartman2015-11-194-20/+82
| |\ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus Johan writes: USB-serial fixes for v4.4-rc2 Here are some new device ids, support for an odd qcserial Gobi interface layout and a fix for the qcserial Huawei interface layout. Signed-off-by: Johan Hovold <johan@kernel.org>
| | * | | USB: qcserial: Fix support for HP lt4112 LTE/HSPA+ Gobi 4G ModemBjørn Mork2015-11-161-20/+34
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The DEVICE_HWI type was added under the faulty assumption that Huawei devices based on Qualcomm chipsets and firmware use the static USB interface numbering known from Gobi devices. But this model does not apply to Huawei devices like the HP branded lt4112 (Huawei me906e). Huawei firmwares will dynamically assign interface numbers. Functions are renumbered when the firmware is reconfigured. Fix by changing the DEVICE_HWI type to use a simplified version of Huawei's subclass + protocol scheme: Blacklisting known network interface combinations and assuming the rest are serial. Reported-and-tested-by: Muri Nicanor <muri+libqmi@immerda.ch> Tested-by: Martin Hauke <mardnh@gmx.de> Cc: <stable@vger.kernel.org> Fixes: e7181d005e84 ("USB: qcserial: Add support for HP lt4112 LTE/HSPA+ Gobi 4G Modem") Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Johan Hovold <johan@kernel.org>
| | * | | USB: ti_usb_3410_5052: Add Honeywell HGI80 IDDavid Woodhouse2015-11-162-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Honeywell HGI80 is a wireless interface to the evohome connected thermostat. It uses a TI 3410 USB-serial port. Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org>
| | * | | USB: serial: option: add support for Novatel MiFi USB620LAleksander Morgado2015-11-161-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Also known as Verizon U620L. The device is modeswitched from 1410:9020 to 1410:9022 by selecting the 4th USB configuration: $ sudo usb_modeswitch –v 0x1410 –p 0x9020 –u 4 This configuration provides a ECM interface as well as TTYs ('Enterprise Mode' according to the U620 Linux integration guide). Signed-off-by: Aleksander Morgado <aleksander@aleksander.es> Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org>
| | * | | USB: qcserial: Add support for Quectel EC20 Mini PCIe modulePetr Štetiar2015-11-161-0/+40
| | |/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It seems like this device has same vendor and product IDs as G2K devices, but it has different number of interfaces(4 vs 5) and also different interface layout which makes it currently unusable: usbcore: registered new interface driver qcserial usbserial: USB Serial support registered for Qualcomm USB modem usb 2-1.2: unknown number of interfaces: 5 lsusb output: Bus 002 Device 003: ID 05c6:9215 Qualcomm, Inc. Acer Gobi 2000 Wireless Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x05c6 Qualcomm, Inc. idProduct 0x9215 Acer Gobi 2000 Wireless Modem bcdDevice 2.32 iManufacturer 1 Quectel iProduct 2 Quectel LTE Module iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 209 bNumInterfaces 5 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xa0 (Bus Powered) Remote Wakeup MaxPower 500mA Signed-off-by: Petr Štetiar <ynezz@true.cz> Cc: stable <stable@vger.kernel.org> [johan: rename define and add comment ] Signed-off-by: Johan Hovold <johan@kernel.org>
generated by cgit (git 2.34.1) at 2025-02-27 22:23:10 +0000