From f1bd9bd69bf8ae96ada7e7f71415bb5f1db453cb Mon Sep 17 00:00:00 2001 From: Joe Perches Date: Fri, 9 Jun 2017 14:54:57 -0300 Subject: media: stkwebcam: Use more common logging styles Convert STK_ to pr_ to use the typical kernel logging. Add a define for pr_fmt. No change in logging output. Miscellanea: o Remove now unused PREFIX and STK_ macros o Realign arguments o Use pr__ratelimited o Add a few missing newlines to formats Signed-off-by: Joe Perches Signed-off-by: Hans Verkuil Signed-off-by: Mauro Carvalho Chehab --- drivers/media/usb/stkwebcam/stk-sensor.c | 32 ++++++++------- drivers/media/usb/stkwebcam/stk-webcam.c | 70 ++++++++++++++++---------------- drivers/media/usb/stkwebcam/stk-webcam.h | 6 --- 3 files changed, 52 insertions(+), 56 deletions(-) (limited to 'drivers/media/usb') diff --git a/drivers/media/usb/stkwebcam/stk-sensor.c b/drivers/media/usb/stkwebcam/stk-sensor.c index 985af9933c7e..c1d4505f84ea 100644 --- a/drivers/media/usb/stkwebcam/stk-sensor.c +++ b/drivers/media/usb/stkwebcam/stk-sensor.c @@ -41,6 +41,8 @@ /* It seems the i2c bus is controlled with these registers */ +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + #include "stk-webcam.h" #define STK_IIC_BASE (0x0200) @@ -239,8 +241,8 @@ static int stk_sensor_outb(struct stk_camera *dev, u8 reg, u8 val) } while (tmpval == 0 && i < MAX_RETRIES); if (tmpval != STK_IIC_STAT_TX_OK) { if (tmpval) - STK_ERROR("stk_sensor_outb failed, status=0x%02x\n", - tmpval); + pr_err("stk_sensor_outb failed, status=0x%02x\n", + tmpval); return 1; } else return 0; @@ -262,8 +264,8 @@ static int stk_sensor_inb(struct stk_camera *dev, u8 reg, u8 *val) } while (tmpval == 0 && i < MAX_RETRIES); if (tmpval != STK_IIC_STAT_RX_OK) { if (tmpval) - STK_ERROR("stk_sensor_inb failed, status=0x%02x\n", - tmpval); + pr_err("stk_sensor_inb failed, status=0x%02x\n", + tmpval); return 1; } @@ -366,29 +368,29 @@ int stk_sensor_init(struct stk_camera *dev) if (stk_camera_write_reg(dev, STK_IIC_ENABLE, STK_IIC_ENABLE_YES) || stk_camera_write_reg(dev, STK_IIC_ADDR, SENSOR_ADDRESS) || stk_sensor_outb(dev, REG_COM7, COM7_RESET)) { - STK_ERROR("Sensor resetting failed\n"); + pr_err("Sensor resetting failed\n"); return -ENODEV; } msleep(10); /* Read the manufacturer ID: ov = 0x7FA2 */ if (stk_sensor_inb(dev, REG_MIDH, &idh) || stk_sensor_inb(dev, REG_MIDL, &idl)) { - STK_ERROR("Strange error reading sensor ID\n"); + pr_err("Strange error reading sensor ID\n"); return -ENODEV; } if (idh != 0x7f || idl != 0xa2) { - STK_ERROR("Huh? you don't have a sensor from ovt\n"); + pr_err("Huh? you don't have a sensor from ovt\n"); return -ENODEV; } if (stk_sensor_inb(dev, REG_PID, &idh) || stk_sensor_inb(dev, REG_VER, &idl)) { - STK_ERROR("Could not read sensor model\n"); + pr_err("Could not read sensor model\n"); return -ENODEV; } stk_sensor_write_regvals(dev, ov_initvals); msleep(10); - STK_INFO("OmniVision sensor detected, id %02X%02X at address %x\n", - idh, idl, SENSOR_ADDRESS); + pr_info("OmniVision sensor detected, id %02X%02X at address %x\n", + idh, idl, SENSOR_ADDRESS); return 0; } @@ -520,7 +522,8 @@ int stk_sensor_configure(struct stk_camera *dev) case MODE_SXGA: com7 = COM7_FMT_SXGA; dummylines = 0; break; - default: STK_ERROR("Unsupported mode %d\n", dev->vsettings.mode); + default: + pr_err("Unsupported mode %d\n", dev->vsettings.mode); return -EFAULT; } switch (dev->vsettings.palette) { @@ -544,7 +547,8 @@ int stk_sensor_configure(struct stk_camera *dev) com7 |= COM7_PBAYER; rv = ov_fmt_bayer; break; - default: STK_ERROR("Unsupported colorspace\n"); + default: + pr_err("Unsupported colorspace\n"); return -EFAULT; } /*FIXME sometimes the sensor go to a bad state @@ -564,7 +568,7 @@ int stk_sensor_configure(struct stk_camera *dev) switch (dev->vsettings.mode) { case MODE_VGA: if (stk_sensor_set_hw(dev, 302, 1582, 6, 486)) - STK_ERROR("stk_sensor_set_hw failed (VGA)\n"); + pr_err("stk_sensor_set_hw failed (VGA)\n"); break; case MODE_SXGA: case MODE_CIF: @@ -572,7 +576,7 @@ int stk_sensor_configure(struct stk_camera *dev) case MODE_QCIF: /*FIXME These settings seem ignored by the sensor if (stk_sensor_set_hw(dev, 220, 1500, 10, 1034)) - STK_ERROR("stk_sensor_set_hw failed (SXGA)\n"); + pr_err("stk_sensor_set_hw failed (SXGA)\n"); */ break; } diff --git a/drivers/media/usb/stkwebcam/stk-webcam.c b/drivers/media/usb/stkwebcam/stk-webcam.c index 6e7fc36b658f..90d4a08cda31 100644 --- a/drivers/media/usb/stkwebcam/stk-webcam.c +++ b/drivers/media/usb/stkwebcam/stk-webcam.c @@ -18,6 +18,8 @@ * GNU General Public License for more details. */ +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + #include #include #include @@ -175,15 +177,15 @@ static int stk_start_stream(struct stk_camera *dev) if (!is_present(dev)) return -ENODEV; if (!is_memallocd(dev) || !is_initialised(dev)) { - STK_ERROR("FIXME: Buffers are not allocated\n"); + pr_err("FIXME: Buffers are not allocated\n"); return -EFAULT; } ret = usb_set_interface(dev->udev, 0, 5); if (ret < 0) - STK_ERROR("usb_set_interface failed !\n"); + pr_err("usb_set_interface failed !\n"); if (stk_sensor_wakeup(dev)) - STK_ERROR("error awaking the sensor\n"); + pr_err("error awaking the sensor\n"); stk_camera_read_reg(dev, 0x0116, &value_116); stk_camera_read_reg(dev, 0x0117, &value_117); @@ -224,9 +226,9 @@ static int stk_stop_stream(struct stk_camera *dev) unset_streaming(dev); if (usb_set_interface(dev->udev, 0, 0)) - STK_ERROR("usb_set_interface failed !\n"); + pr_err("usb_set_interface failed !\n"); if (stk_sensor_sleep(dev)) - STK_ERROR("error suspending the sensor\n"); + pr_err("error suspending the sensor\n"); } return 0; } @@ -313,7 +315,7 @@ static void stk_isoc_handler(struct urb *urb) dev = (struct stk_camera *) urb->context; if (dev == NULL) { - STK_ERROR("isoc_handler called with NULL device !\n"); + pr_err("isoc_handler called with NULL device !\n"); return; } @@ -326,14 +328,13 @@ static void stk_isoc_handler(struct urb *urb) spin_lock_irqsave(&dev->spinlock, flags); if (urb->status != -EINPROGRESS && urb->status != 0) { - STK_ERROR("isoc_handler: urb->status == %d\n", urb->status); + pr_err("isoc_handler: urb->status == %d\n", urb->status); goto resubmit; } if (list_empty(&dev->sio_avail)) { /*FIXME Stop streaming after a while */ - (void) (printk_ratelimit() && - STK_ERROR("isoc_handler without available buffer!\n")); + pr_err_ratelimited("isoc_handler without available buffer!\n"); goto resubmit; } fb = list_first_entry(&dev->sio_avail, @@ -343,8 +344,8 @@ static void stk_isoc_handler(struct urb *urb) for (i = 0; i < urb->number_of_packets; i++) { if (urb->iso_frame_desc[i].status != 0) { if (urb->iso_frame_desc[i].status != -EXDEV) - STK_ERROR("Frame %d has error %d\n", i, - urb->iso_frame_desc[i].status); + pr_err("Frame %d has error %d\n", + i, urb->iso_frame_desc[i].status); continue; } framelen = urb->iso_frame_desc[i].actual_length; @@ -368,9 +369,8 @@ static void stk_isoc_handler(struct urb *urb) /* This marks a new frame */ if (fb->v4lbuf.bytesused != 0 && fb->v4lbuf.bytesused != dev->frame_size) { - (void) (printk_ratelimit() && - STK_ERROR("frame %d, bytesused=%d, skipping\n", - i, fb->v4lbuf.bytesused)); + pr_err_ratelimited("frame %d, bytesused=%d, skipping\n", + i, fb->v4lbuf.bytesused); fb->v4lbuf.bytesused = 0; fill = fb->buffer; } else if (fb->v4lbuf.bytesused == dev->frame_size) { @@ -395,8 +395,7 @@ static void stk_isoc_handler(struct urb *urb) /* Our buffer is full !!! */ if (framelen + fb->v4lbuf.bytesused > dev->frame_size) { - (void) (printk_ratelimit() && - STK_ERROR("Frame buffer overflow, lost sync\n")); + pr_err_ratelimited("Frame buffer overflow, lost sync\n"); /*FIXME Do something here? */ continue; } @@ -414,8 +413,8 @@ resubmit: urb->dev = dev->udev; ret = usb_submit_urb(urb, GFP_ATOMIC); if (ret != 0) { - STK_ERROR("Error (%d) re-submitting urb in stk_isoc_handler.\n", - ret); + pr_err("Error (%d) re-submitting urb in stk_isoc_handler\n", + ret); } } @@ -433,32 +432,31 @@ static int stk_prepare_iso(struct stk_camera *dev) udev = dev->udev; if (dev->isobufs) - STK_ERROR("isobufs already allocated. Bad\n"); + pr_err("isobufs already allocated. Bad\n"); else dev->isobufs = kcalloc(MAX_ISO_BUFS, sizeof(*dev->isobufs), GFP_KERNEL); if (dev->isobufs == NULL) { - STK_ERROR("Unable to allocate iso buffers\n"); + pr_err("Unable to allocate iso buffers\n"); return -ENOMEM; } for (i = 0; i < MAX_ISO_BUFS; i++) { if (dev->isobufs[i].data == NULL) { kbuf = kzalloc(ISO_BUFFER_SIZE, GFP_KERNEL); if (kbuf == NULL) { - STK_ERROR("Failed to allocate iso buffer %d\n", - i); + pr_err("Failed to allocate iso buffer %d\n", i); goto isobufs_out; } dev->isobufs[i].data = kbuf; } else - STK_ERROR("isobuf data already allocated\n"); + pr_err("isobuf data already allocated\n"); if (dev->isobufs[i].urb == NULL) { urb = usb_alloc_urb(ISO_FRAMES_PER_DESC, GFP_KERNEL); if (urb == NULL) goto isobufs_out; dev->isobufs[i].urb = urb; } else { - STK_ERROR("Killing URB\n"); + pr_err("Killing URB\n"); usb_kill_urb(dev->isobufs[i].urb); urb = dev->isobufs[i].urb; } @@ -567,7 +565,7 @@ static int stk_prepare_sio_buffers(struct stk_camera *dev, unsigned n_sbufs) { int i; if (dev->sio_bufs != NULL) - STK_ERROR("sio_bufs already allocated\n"); + pr_err("sio_bufs already allocated\n"); else { dev->sio_bufs = kzalloc(n_sbufs * sizeof(struct stk_sio_buffer), GFP_KERNEL); @@ -690,7 +688,7 @@ static ssize_t stk_read(struct file *fp, char __user *buf, spin_lock_irqsave(&dev->spinlock, flags); if (list_empty(&dev->sio_full)) { spin_unlock_irqrestore(&dev->spinlock, flags); - STK_ERROR("BUG: No siobufs ready\n"); + pr_err("BUG: No siobufs ready\n"); return 0; } sbuf = list_first_entry(&dev->sio_full, struct stk_sio_buffer, list); @@ -907,7 +905,7 @@ static int stk_vidioc_g_fmt_vid_cap(struct file *filp, stk_sizes[i].m != dev->vsettings.mode; i++) ; if (i == ARRAY_SIZE(stk_sizes)) { - STK_ERROR("ERROR: mode invalid\n"); + pr_err("ERROR: mode invalid\n"); return -EINVAL; } pix_format->width = stk_sizes[i].w; @@ -985,7 +983,7 @@ static int stk_setup_format(struct stk_camera *dev) stk_sizes[i].m != dev->vsettings.mode) i++; if (i == ARRAY_SIZE(stk_sizes)) { - STK_ERROR("Something is broken in %s\n", __func__); + pr_err("Something is broken in %s\n", __func__); return -EFAULT; } /* This registers controls some timings, not sure of what. */ @@ -1241,7 +1239,7 @@ static void stk_v4l_dev_release(struct video_device *vd) struct stk_camera *dev = vdev_to_camera(vd); if (dev->sio_bufs != NULL || dev->isobufs != NULL) - STK_ERROR("We are leaking memory\n"); + pr_err("We are leaking memory\n"); usb_put_intf(dev->interface); kfree(dev); } @@ -1264,10 +1262,10 @@ static int stk_register_video_device(struct stk_camera *dev) video_set_drvdata(&dev->vdev, dev); err = video_register_device(&dev->vdev, VFL_TYPE_GRABBER, -1); if (err) - STK_ERROR("v4l registration failed\n"); + pr_err("v4l registration failed\n"); else - STK_INFO("Syntek USB2.0 Camera is now controlling device %s\n", - video_device_node_name(&dev->vdev)); + pr_info("Syntek USB2.0 Camera is now controlling device %s\n", + video_device_node_name(&dev->vdev)); return err; } @@ -1288,7 +1286,7 @@ static int stk_camera_probe(struct usb_interface *interface, dev = kzalloc(sizeof(struct stk_camera), GFP_KERNEL); if (dev == NULL) { - STK_ERROR("Out of memory !\n"); + pr_err("Out of memory !\n"); return -ENOMEM; } err = v4l2_device_register(&interface->dev, &dev->v4l2_dev); @@ -1352,7 +1350,7 @@ static int stk_camera_probe(struct usb_interface *interface, } } if (!dev->isoc_ep) { - STK_ERROR("Could not find isoc-in endpoint"); + pr_err("Could not find isoc-in endpoint\n"); err = -ENODEV; goto error; } @@ -1387,8 +1385,8 @@ static void stk_camera_disconnect(struct usb_interface *interface) wake_up_interruptible(&dev->wait_frame); - STK_INFO("Syntek USB2.0 Camera release resources device %s\n", - video_device_node_name(&dev->vdev)); + pr_info("Syntek USB2.0 Camera release resources device %s\n", + video_device_node_name(&dev->vdev)); video_unregister_device(&dev->vdev); v4l2_ctrl_handler_free(&dev->hdl); diff --git a/drivers/media/usb/stkwebcam/stk-webcam.h b/drivers/media/usb/stkwebcam/stk-webcam.h index 0284120ce246..5cecbdc97573 100644 --- a/drivers/media/usb/stkwebcam/stk-webcam.h +++ b/drivers/media/usb/stkwebcam/stk-webcam.h @@ -31,12 +31,6 @@ #define ISO_MAX_FRAME_SIZE 3 * 1024 #define ISO_BUFFER_SIZE (ISO_FRAMES_PER_DESC * ISO_MAX_FRAME_SIZE) - -#define PREFIX "stkwebcam: " -#define STK_INFO(str, args...) printk(KERN_INFO PREFIX str, ##args) -#define STK_ERROR(str, args...) printk(KERN_ERR PREFIX str, ##args) -#define STK_WARNING(str, args...) printk(KERN_WARNING PREFIX str, ##args) - struct stk_iso_buf { void *data; int length; -- cgit From 0a0c1b823cbc0b72eb6e0c2cfe5704cf80fe842d Mon Sep 17 00:00:00 2001 From: Arnd Bergmann Date: Wed, 21 Jun 2017 19:10:32 -0300 Subject: media: rainshadow-cec: avoid -Wmaybe-uninitialized warning again Back in April I created a patch to address a false-positive warning: drivers/media/usb/rainshadow-cec/rainshadow-cec.c: In function 'rain_irq_work_handler': drivers/media/usb/rainshadow-cec/rainshadow-cec.c:171:31: error: 'data' may be used uninitialized in this function [-Werror=maybe-uninitialized] My patch was totally wrong and introduced a real bug, and Colin Ian King thankfully noticed it now and fixed my mistake. Unfortunately, fixing the actual uninitialized data in this case brought back the original bogus warning. This is a new version of the patch, which simplifies the code to the point where gcc notices the behavior is correct. Fixes: ca33784ba494 ("[media] rainshadow-cec: ensure exit_loop is intialized") Fixes: ea6a69defd3311 ("[media] rainshadow-cec: avoid -Wmaybe-uninitialized warning") Cc: Colin Ian King Signed-off-by: Arnd Bergmann Signed-off-by: Hans Verkuil Signed-off-by: Mauro Carvalho Chehab --- drivers/media/usb/rainshadow-cec/rainshadow-cec.c | 18 ++++++++---------- 1 file changed, 8 insertions(+), 10 deletions(-) (limited to 'drivers/media/usb') diff --git a/drivers/media/usb/rainshadow-cec/rainshadow-cec.c b/drivers/media/usb/rainshadow-cec/rainshadow-cec.c index f203699e9c1b..65692576690f 100644 --- a/drivers/media/usb/rainshadow-cec/rainshadow-cec.c +++ b/drivers/media/usb/rainshadow-cec/rainshadow-cec.c @@ -116,21 +116,19 @@ static void rain_irq_work_handler(struct work_struct *work) while (true) { unsigned long flags; - bool exit_loop = false; char data; spin_lock_irqsave(&rain->buf_lock, flags); - if (rain->buf_len) { - data = rain->buf[rain->buf_rd_idx]; - rain->buf_len--; - rain->buf_rd_idx = (rain->buf_rd_idx + 1) & 0xff; - } else { - exit_loop = true; + if (!rain->buf_len) { + spin_unlock_irqrestore(&rain->buf_lock, flags); + break; } - spin_unlock_irqrestore(&rain->buf_lock, flags); - if (exit_loop) - break; + data = rain->buf[rain->buf_rd_idx]; + rain->buf_len--; + rain->buf_rd_idx = (rain->buf_rd_idx + 1) & 0xff; + + spin_unlock_irqrestore(&rain->buf_lock, flags); if (!rain->cmd_started && data != '?') continue; -- cgit From d18a6ef59c53022b4af222412dc494cfd21c298e Mon Sep 17 00:00:00 2001 From: Dan Carpenter Date: Fri, 28 Apr 2017 09:52:07 -0300 Subject: media: dib0700: fix locking in dib0700_i2c_xfer_new() This patch mostly adds unlocks to error paths. But one additional small change is that I made the first "break;" a "goto unlock;" which means that now we return failure instead of success on that path. Signed-off-by: Dan Carpenter Signed-off-by: Mauro Carvalho Chehab --- drivers/media/usb/dvb-usb/dib0700_core.c | 18 ++++++++++++------ 1 file changed, 12 insertions(+), 6 deletions(-) (limited to 'drivers/media/usb') diff --git a/drivers/media/usb/dvb-usb/dib0700_core.c b/drivers/media/usb/dvb-usb/dib0700_core.c index 08acdd32e412..4dea79718827 100644 --- a/drivers/media/usb/dvb-usb/dib0700_core.c +++ b/drivers/media/usb/dvb-usb/dib0700_core.c @@ -215,13 +215,14 @@ static int dib0700_i2c_xfer_new(struct i2c_adapter *adap, struct i2c_msg *msg, USB_CTRL_GET_TIMEOUT); if (result < 0) { deb_info("i2c read error (status = %d)\n", result); - break; + goto unlock; } if (msg[i].len > sizeof(st->buf)) { deb_info("buffer too small to fit %d bytes\n", msg[i].len); - return -EIO; + result = -EIO; + goto unlock; } memcpy(msg[i].buf, st->buf, msg[i].len); @@ -233,8 +234,8 @@ static int dib0700_i2c_xfer_new(struct i2c_adapter *adap, struct i2c_msg *msg, /* Write request */ if (mutex_lock_interruptible(&d->usb_mutex) < 0) { err("could not acquire lock"); - mutex_unlock(&d->i2c_mutex); - return -EINTR; + result = -EINTR; + goto unlock; } st->buf[0] = REQUEST_NEW_I2C_WRITE; st->buf[1] = msg[i].addr << 1; @@ -247,7 +248,9 @@ static int dib0700_i2c_xfer_new(struct i2c_adapter *adap, struct i2c_msg *msg, if (msg[i].len > sizeof(st->buf) - 4) { deb_info("i2c message to big: %d\n", msg[i].len); - return -EIO; + mutex_unlock(&d->usb_mutex); + result = -EIO; + goto unlock; } /* The Actual i2c payload */ @@ -269,8 +272,11 @@ static int dib0700_i2c_xfer_new(struct i2c_adapter *adap, struct i2c_msg *msg, } } } + result = i; + +unlock: mutex_unlock(&d->i2c_mutex); - return i; + return result; } /* -- cgit From 66083b49bd337e5f4dfa168c145ca38f8bcbe522 Mon Sep 17 00:00:00 2001 From: Dan Carpenter Date: Fri, 28 Apr 2017 09:53:31 -0300 Subject: media: dib0700: fix error handling in dib0700_i2c_xfer_legacy() Mostly this adds some unlocks to error paths. But, if you see where there were "break;" statements before, I changed those paths to return error codes instead of returning success. Signed-off-by: Dan Carpenter Signed-off-by: Mauro Carvalho Chehab --- drivers/media/usb/dvb-usb/dib0700_core.c | 20 +++++++++++++------- 1 file changed, 13 insertions(+), 7 deletions(-) (limited to 'drivers/media/usb') diff --git a/drivers/media/usb/dvb-usb/dib0700_core.c b/drivers/media/usb/dvb-usb/dib0700_core.c index 4dea79718827..bea1b4764a66 100644 --- a/drivers/media/usb/dvb-usb/dib0700_core.c +++ b/drivers/media/usb/dvb-usb/dib0700_core.c @@ -287,7 +287,7 @@ static int dib0700_i2c_xfer_legacy(struct i2c_adapter *adap, { struct dvb_usb_device *d = i2c_get_adapdata(adap); struct dib0700_state *st = d->priv; - int i,len; + int i, len, result; if (mutex_lock_interruptible(&d->i2c_mutex) < 0) return -EINTR; @@ -304,7 +304,8 @@ static int dib0700_i2c_xfer_legacy(struct i2c_adapter *adap, if (msg[i].len > sizeof(st->buf) - 2) { deb_info("i2c xfer to big: %d\n", msg[i].len); - return -EIO; + result = -EIO; + goto unlock; } memcpy(&st->buf[2], msg[i].buf, msg[i].len); @@ -319,13 +320,15 @@ static int dib0700_i2c_xfer_legacy(struct i2c_adapter *adap, if (len <= 0) { deb_info("I2C read failed on address 0x%02x\n", msg[i].addr); - break; + result = -EIO; + goto unlock; } if (msg[i + 1].len > sizeof(st->buf)) { deb_info("i2c xfer buffer to small for %d\n", msg[i].len); - return -EIO; + result = -EIO; + goto unlock; } memcpy(msg[i + 1].buf, st->buf, msg[i + 1].len); @@ -334,14 +337,17 @@ static int dib0700_i2c_xfer_legacy(struct i2c_adapter *adap, i++; } else { st->buf[0] = REQUEST_I2C_WRITE; - if (dib0700_ctrl_wr(d, st->buf, msg[i].len + 2) < 0) - break; + result = dib0700_ctrl_wr(d, st->buf, msg[i].len + 2); + if (result < 0) + goto unlock; } } + result = i; +unlock: mutex_unlock(&d->usb_mutex); mutex_unlock(&d->i2c_mutex); - return i; + return result; } static int dib0700_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg *msg, -- cgit From b1e1d4532e073c4e6a47efd7e447fceb37528ad9 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Tue, 2 May 2017 23:12:22 -0300 Subject: media: em28xx: Ignore errors while reading from eeprom MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit While testing support for Terratec H6 rev. 2, it was noticed that reading from eeprom there causes a timeout error. Apparently, this is due to the need of properly setting GPIOs. In any case, the driver doesn't really require eeprom reading to succeed, as this is currently used only for debug. So, Ignore such errors. Signed-off-by: Mauro Carvalho Chehab Acked-by: Frank Schäfer Signed-off-by: Mauro Carvalho Chehab --- drivers/media/usb/em28xx/em28xx-i2c.c | 2 -- 1 file changed, 2 deletions(-) (limited to 'drivers/media/usb') diff --git a/drivers/media/usb/em28xx/em28xx-i2c.c b/drivers/media/usb/em28xx/em28xx-i2c.c index 8c472d5adb50..60b195c157b8 100644 --- a/drivers/media/usb/em28xx/em28xx-i2c.c +++ b/drivers/media/usb/em28xx/em28xx-i2c.c @@ -982,8 +982,6 @@ int em28xx_i2c_register(struct em28xx *dev, unsigned bus, dev_err(&dev->intf->dev, "%s: em28xx_i2_eeprom failed! retval [%d]\n", __func__, retval); - - return retval; } } -- cgit From d6a643275a3659946398cd42e5df805546f9e247 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Tue, 2 May 2017 23:12:23 -0300 Subject: media: em28xx: add support for new of Terratec H6 There's a new version of Terratec H6 with uses USB ID 0ccd:10b2. This version is similar to the old one (with is supported via the HTC entry), except that this one has the eeprom on the second bus. On this board, one side of this board is labeled with: dvbc v2.0 The other side with: 94V-0, MO2, RK-4221 with huge digits: 1107 With those patches, the board is properly detected: em28xx 1-1.5:1.0: New device TERRATEC TERRATCE H5 MKII @ 480 Mbps (0ccd:10b2, interface 0, class 0) em28xx 1-1.5:1.0: Audio interface 0 found (Vendor Class) em28xx 1-1.5:1.0: Video interface 0 found: isoc em28xx 1-1.5:1.0: DVB interface 0 found: isoc em28xx 1-1.5:1.0: chip ID is em2884 em28xx eeprom 00000000: 26 00 00 00 02 0b 0f e5 f5 64 01 60 09 e5 f5 64 &........d.`...d em28xx eeprom 00000010: 09 60 03 c2 c6 22 e5 f7 b4 03 13 e5 f6 b4 87 03 .`...".......... em28xx eeprom 00000020: 02 0a b9 e5 f6 b4 93 03 02 09 46 c2 c6 22 c2 c6 ..........F..".. em28xx eeprom 00000030: 22 00 60 00 ef 70 08 85 3d 82 85 3c 83 93 ff ef ".`..p..=..<.... em28xx eeprom 00000040: 60 19 85 3d 82 85 3c 83 e4 93 12 07 a3 12 0a fe `..=..<......... em28xx eeprom 00000050: 05 3d e5 3d 70 02 05 3c 1f 80 e4 22 12 0b 06 02 .=.=p..<...".... em28xx eeprom 00000060: 07 e2 01 00 1a eb 67 95 cd 0c b2 10 f0 13 6b 03 ......g.......k. em28xx eeprom 00000070: 98 22 6a 1c 86 12 27 57 4e 16 29 00 60 00 00 00 ."j...'WN.).`... em28xx eeprom 00000080: 02 00 00 00 5e 00 13 00 f0 10 44 82 82 00 00 00 ....^.....D..... em28xx eeprom 00000090: 5b 81 c0 00 00 00 20 40 20 80 02 20 10 01 00 00 [..... @ .. .... em28xx eeprom 000000a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ em28xx eeprom 000000b0: c6 40 00 00 81 00 00 00 00 00 00 00 00 c4 00 00 .@.............. em28xx eeprom 000000c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 1c 03 ................ em28xx eeprom 000000d0: 31 00 32 00 33 00 34 00 35 00 36 00 37 00 38 00 1.2.3.4.5.6.7.8. em28xx eeprom 000000e0: 39 00 41 00 42 00 43 00 44 00 12 03 54 00 45 00 9.A.B.C.D...T.E. em28xx eeprom 000000f0: 52 00 52 00 41 00 54 00 45 00 43 00 22 03 54 00 R.R.A.T.E.C.".T. em28xx 1-1.5:1.0: eeprom 000100: ... (skipped) em28xx 1-1.5:1.0: EEPROM ID = 26 00 00 00, EEPROM hash = 0xbcd5a8cf em28xx 1-1.5:1.0: EEPROM info: em28xx 1-1.5:1.0: microcode start address = 0x0004, boot configuration = 0x00 em28xx 1-1.5:1.0: I2S audio, 5 sample rates em28xx 1-1.5:1.0: 500mA max power em28xx 1-1.5:1.0: Table at offset 0x27, strings=0x2298, 0x1c6a, 0x1286 em28xx 1-1.5:1.0: Identified as Terratec Cinergy H6 rev. 2 (card=101) em28xx 1-1.5:1.0: Currently, V4L2 is not supported on this model em28xx 1-1.5:1.0: dvb set to isoc mode. usbcore: registered new interface driver em28xx em28xx 1-1.5:1.0: Binding audio extension em28xx 1-1.5:1.0: em28xx-audio.c: Copyright (C) 2006 Markus Rechberger em28xx 1-1.5:1.0: em28xx-audio.c: Copyright (C) 2007-2016 Mauro Carvalho Chehab em28xx 1-1.5:1.0: Endpoint 0x83 high-speed on intf 0 alt 7 interval = 8, size 196 em28xx 1-1.5:1.0: Number of URBs: 1, with 64 packets and 192 size em28xx 1-1.5:1.0: Audio extension successfully initialized em28xx: Registered (Em28xx Audio Extension) extension em28xx 1-1.5:1.0: Binding DVB extension drxk: status = 0x639260d9 drxk: detected a drx-3926k, spin A3, xtal 20.250 MHz drxk: DRXK driver version 0.9.4300 drxk: frontend initialized. tda18271 4-0060: creating new instance tda18271: TDA18271HD/C2 detected @ 4-0060 dvbdev: DVB: registering new adapter (1-1.5:1.0) em28xx 1-1.5:1.0: DVB: registering adapter 0 frontend 0 (DRXK DVB-C DVB-T)... dvbdev: dvb_create_media_entity: media entity 'DRXK DVB-C DVB-T' registered. dvbdev: dvb_create_media_entity: media entity 'dvb-demux' registered. em28xx 1-1.5:1.0: DVB extension successfully initialized em28xx: Registered (Em28xx dvb Extension) extension em28xx 1-1.5:1.0: Registering input extension rc rc0: 1-1.5:1.0 IR as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.5/1-1.5:1.0/rc/rc0 Registered IR keymap rc-nec-terratec-cinergy-xs input: 1-1.5:1.0 IR as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.5/1-1.5:1.0/rc/rc0/input0 em28xx 1-1.5:1.0: Input extension successfully initalized em28xx: Registered (Em28xx Input Extension) extension tda18271: performing RF tracking filter calibration tda18271: RF tracking filter calibration complete Signed-off-by: Mauro Carvalho Chehab --- drivers/media/usb/em28xx/em28xx-cards.c | 18 ++++++++++++++++++ drivers/media/usb/em28xx/em28xx-dvb.c | 1 + drivers/media/usb/em28xx/em28xx.h | 1 + 3 files changed, 20 insertions(+) (limited to 'drivers/media/usb') diff --git a/drivers/media/usb/em28xx/em28xx-cards.c b/drivers/media/usb/em28xx/em28xx-cards.c index 146341aeb782..4c57fd7929cb 100644 --- a/drivers/media/usb/em28xx/em28xx-cards.c +++ b/drivers/media/usb/em28xx/em28xx-cards.c @@ -1188,6 +1188,22 @@ struct em28xx_board em28xx_boards[] = { .tuner_gpio = terratec_h5_gpio, #else .tuner_type = TUNER_ABSENT, +#endif + .def_i2c_bus = 1, + .i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE | + EM28XX_I2C_FREQ_400_KHZ, + }, + [EM2884_BOARD_TERRATEC_H6] = { + .name = "Terratec Cinergy H6 rev. 2", + .has_dvb = 1, + .ir_codes = RC_MAP_NEC_TERRATEC_CINERGY_XS, +#if 0 + .tuner_type = TUNER_PHILIPS_TDA8290, + .tuner_addr = 0x41, + .dvb_gpio = terratec_h5_digital, /* FIXME: probably wrong */ + .tuner_gpio = terratec_h5_gpio, +#else + .tuner_type = TUNER_ABSENT, #endif .def_i2c_bus = 1, .i2c_speed = EM28XX_I2C_CLK_WAIT_ENABLE | @@ -2496,6 +2512,8 @@ struct usb_device_id em28xx_id_table[] = { .driver_info = EM2884_BOARD_TERRATEC_H5 }, { USB_DEVICE(0x0ccd, 0x10b6), /* H5 Rev. 3 */ .driver_info = EM2884_BOARD_TERRATEC_H5 }, + { USB_DEVICE(0x0ccd, 0x10b2), /* H6 */ + .driver_info = EM2884_BOARD_TERRATEC_H6 }, { USB_DEVICE(0x0ccd, 0x0084), .driver_info = EM2860_BOARD_TERRATEC_AV350 }, { USB_DEVICE(0x0ccd, 0x0096), diff --git a/drivers/media/usb/em28xx/em28xx-dvb.c b/drivers/media/usb/em28xx/em28xx-dvb.c index 82edd37f0d73..4a7db623fe29 100644 --- a/drivers/media/usb/em28xx/em28xx-dvb.c +++ b/drivers/media/usb/em28xx/em28xx-dvb.c @@ -1522,6 +1522,7 @@ static int em28xx_dvb_init(struct em28xx *dev) break; case EM2884_BOARD_ELGATO_EYETV_HYBRID_2008: case EM2884_BOARD_CINERGY_HTC_STICK: + case EM2884_BOARD_TERRATEC_H6: terratec_htc_stick_init(dev); /* attach demodulator */ diff --git a/drivers/media/usb/em28xx/em28xx.h b/drivers/media/usb/em28xx/em28xx.h index e8d97d5ec161..88084f24f033 100644 --- a/drivers/media/usb/em28xx/em28xx.h +++ b/drivers/media/usb/em28xx/em28xx.h @@ -148,6 +148,7 @@ #define EM28178_BOARD_PLEX_PX_BCUD 98 #define EM28174_BOARD_HAUPPAUGE_WINTV_DUALHD_DVB 99 #define EM28174_BOARD_HAUPPAUGE_WINTV_DUALHD_01595 100 +#define EM2884_BOARD_TERRATEC_H6 101 /* Limits minimum and default number of buffers */ #define EM28XX_MIN_BUF 4 -- cgit From 1250a85b1b5c6b40c2ae32cd61a7029094530d31 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Sat, 24 Jun 2017 15:46:24 -0300 Subject: media: Replace initalized ->initialized While committing a change on em28xx, I got a warning of a typo there. So, fix it on em28xx and on two other media drivers with the same typo. Signed-off-by: Mauro Carvalho Chehab --- drivers/media/usb/au0828/au0828-input.c | 2 +- drivers/media/usb/em28xx/em28xx-input.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers/media/usb') diff --git a/drivers/media/usb/au0828/au0828-input.c b/drivers/media/usb/au0828/au0828-input.c index 9ec919c68482..9d82ec0a4b64 100644 --- a/drivers/media/usb/au0828/au0828-input.c +++ b/drivers/media/usb/au0828/au0828-input.c @@ -351,7 +351,7 @@ int au0828_rc_register(struct au0828_dev *dev) if (err) goto error; - pr_info("Remote controller %s initalized\n", ir->name); + pr_info("Remote controller %s initialized\n", ir->name); return 0; diff --git a/drivers/media/usb/em28xx/em28xx-input.c b/drivers/media/usb/em28xx/em28xx-input.c index eba75736e654..ca9673917ad5 100644 --- a/drivers/media/usb/em28xx/em28xx-input.c +++ b/drivers/media/usb/em28xx/em28xx-input.c @@ -821,7 +821,7 @@ static int em28xx_ir_init(struct em28xx *dev) if (err) goto error; - dev_info(&dev->intf->dev, "Input extension successfully initalized\n"); + dev_info(&dev->intf->dev, "Input extension successfully initialized\n"); return 0; -- cgit From d83bc7b644004131185aaa875e52bdcc3cd5f031 Mon Sep 17 00:00:00 2001 From: "Gustavo A. R. Silva" Date: Thu, 22 Jun 2017 01:22:47 -0300 Subject: media: dvb-usb-v2: lmedm04: remove unnecessary variable in lme2510_stream_restart() Remove unnecessary variable _ret_ and refactor the code. Addresses-Coverity-ID: 1226934 Signed-off-by: Gustavo A. R. Silva Signed-off-by: Mauro Carvalho Chehab --- drivers/media/usb/dvb-usb-v2/lmedm04.c | 10 ++++------ 1 file changed, 4 insertions(+), 6 deletions(-) (limited to 'drivers/media/usb') diff --git a/drivers/media/usb/dvb-usb-v2/lmedm04.c b/drivers/media/usb/dvb-usb-v2/lmedm04.c index 594360a63c18..a91fdad8f8d4 100644 --- a/drivers/media/usb/dvb-usb-v2/lmedm04.c +++ b/drivers/media/usb/dvb-usb-v2/lmedm04.c @@ -207,15 +207,13 @@ static int lme2510_stream_restart(struct dvb_usb_device *d) struct lme2510_state *st = d->priv; u8 all_pids[] = LME_ALL_PIDS; u8 stream_on[] = LME_ST_ON_W; - int ret; u8 rbuff[1]; if (st->pid_off) - ret = lme2510_usb_talk(d, all_pids, sizeof(all_pids), - rbuff, sizeof(rbuff)); + lme2510_usb_talk(d, all_pids, sizeof(all_pids), + rbuff, sizeof(rbuff)); /*Restart Stream Command*/ - ret = lme2510_usb_talk(d, stream_on, sizeof(stream_on), - rbuff, sizeof(rbuff)); - return ret; + return lme2510_usb_talk(d, stream_on, sizeof(stream_on), + rbuff, sizeof(rbuff)); } static int lme2510_enable_pid(struct dvb_usb_device *d, u8 index, u16 pid_out) -- cgit From 9b7c0c476f66ee212925c801c4141fdd83b7336d Mon Sep 17 00:00:00 2001 From: Hans Verkuil Date: Sun, 16 Jul 2017 05:15:47 -0300 Subject: media: pulse8-cec: persistent_config should be off by default The persistent_config option is used to make the CEC settings persistent by using the eeprom inside the device to store this information. This was on by default, which caused confusion since this device now behaves differently from other CEC devices which all come up unconfigured. Another reason for doing this now is that I hope a more standard way of selecting persistent configuration will be created in the future. And for that to work all CEC drivers should behave the same and come up unconfigured by default. None of the open source CEC applications are using this CEC framework at the moment so change this behavior before it is too late. Signed-off-by: Hans Verkuil Cc: # for v4.10 and up Signed-off-by: Mauro Carvalho Chehab --- drivers/media/usb/pulse8-cec/pulse8-cec.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/media/usb') diff --git a/drivers/media/usb/pulse8-cec/pulse8-cec.c b/drivers/media/usb/pulse8-cec/pulse8-cec.c index c843070f24c1..f9ed9c950247 100644 --- a/drivers/media/usb/pulse8-cec/pulse8-cec.c +++ b/drivers/media/usb/pulse8-cec/pulse8-cec.c @@ -51,7 +51,7 @@ MODULE_DESCRIPTION("Pulse Eight HDMI CEC driver"); MODULE_LICENSE("GPL"); static int debug; -static int persistent_config = 1; +static int persistent_config; module_param(debug, int, 0644); module_param(persistent_config, int, 0644); MODULE_PARM_DESC(debug, "debug level (0-1)"); -- cgit