Merge branch 'master' into next

Signed-off-by: Tom Rini <trini@konsulko.com>

15 files changed, 234 insertions, 11 deletions

diff --git a/board/freescale/imxrt1170-evk/Kconfig b/board/freescale/imxrt1170-evk/Kconfig
new file mode 100644
index 00000000000..c61fc579713
--- /dev/null
+++ b/board/freescale/imxrt1170-evk/Kconfig
@@ -0,0 +1,22 @@
+if TARGET_IMXRT1170_EVK
+
+config SYS_BOARD
+	string
+	default "imxrt1170-evk"
+
+config SYS_VENDOR
+	string
+	default "freescale"
+
+config SYS_SOC
+	string
+	default "imxrt1170"
+
+config SYS_CONFIG_NAME
+	string
+	default "imxrt1170-evk"
+
+config IMX_CONFIG
+	default "board/freescale/imxrt1170-evk/imximage.cfg"
+
+endif
diff --git a/board/freescale/imxrt1170-evk/MAINTAINERS b/board/freescale/imxrt1170-evk/MAINTAINERS
new file mode 100644
index 00000000000..1fc3179c005
--- /dev/null
+++ b/board/freescale/imxrt1170-evk/MAINTAINERS
@@ -0,0 +1,7 @@
+IMXRT1170 EVALUATION KIT
+M:	Giulio Benetti <giulio.benetti@benettiengineering.com>
+M:	Jesse Taube <Mr.Bossman075@gmail.com>
+S:	Maintained
+F:	board/freescale/imxrt1170-evk
+F:	include/configs/imxrt1170-evk.h
+F:	configs/imxrt1170-evk_defconfig
diff --git a/board/freescale/imxrt1170-evk/Makefile b/board/freescale/imxrt1170-evk/Makefile
new file mode 100644
index 00000000000..857a168b09d
--- /dev/null
+++ b/board/freescale/imxrt1170-evk/Makefile
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# Copyright (C) 2019
+# Author(s): Giulio Benetti <giulio.benetti@benettiengineering.com>
+
+obj-y	:= imxrt1170-evk.o
diff --git a/board/freescale/imxrt1170-evk/imximage.cfg b/board/freescale/imxrt1170-evk/imximage.cfg
new file mode 100644
index 00000000000..57583d04ce6
--- /dev/null
+++ b/board/freescale/imxrt1170-evk/imximage.cfg
@@ -0,0 +1,31 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2022
+ * Author(s): Jesse Taube <Mr.Bossman075@gmail.com>
+ * Giulio Benetti <giulio.benetti@benettiengineering.com>
+ */
+
+#include <config.h>
+
+/* image version */
+
+IMAGE_VERSION 2
+
+/*
+ * Boot Device : one of
+ * spi/sd/nand/onenand, qspi/nor
+ */
+
+BOOT_FROM	sd
+
+/*
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type           Address        Value
+ *
+ * where:
+ *	Addr-type register length (1,2 or 4 bytes)
+ *	Address	  absolute address of the register
+ *	value	  value to be stored in the register
+ */
diff --git a/board/freescale/imxrt1170-evk/imxrt1170-evk.c b/board/freescale/imxrt1170-evk/imxrt1170-evk.c
new file mode 100644
index 00000000000..4b82ee5e9ce
--- /dev/null
+++ b/board/freescale/imxrt1170-evk/imxrt1170-evk.c
@@ -0,0 +1,80 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2019
+ * Author(s): Giulio Benetti <giulio.benetti@benettiengineering.com>
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <init.h>
+#include <log.h>
+#include <ram.h>
+#include <spl.h>
+#include <asm/global_data.h>
+#include <asm/io.h>
+#include <asm/armv7m.h>
+#include <serial.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int dram_init(void)
+{
+#ifndef CONFIG_SUPPORT_SPL
+	int rv;
+	struct udevice *dev;
+
+	rv = uclass_get_device(UCLASS_RAM, 0, &dev);
+	if (rv) {
+		debug("DRAM init failed: %d\n", rv);
+		return rv;
+	}
+
+#endif
+	return fdtdec_setup_mem_size_base();
+}
+
+int dram_init_banksize(void)
+{
+	return fdtdec_setup_memory_banksize();
+}
+
+#ifdef CONFIG_SPL_BUILD
+#ifdef CONFIG_SPL_OS_BOOT
+int spl_start_uboot(void)
+{
+	debug("SPL: booting kernel\n");
+	/* break into full u-boot on 'c' */
+	return serial_tstc() && serial_getc() == 'c';
+}
+#endif
+
+int spl_dram_init(void)
+{
+	struct udevice *dev;
+	int rv;
+
+	rv = uclass_get_device(UCLASS_RAM, 0, &dev);
+	if (rv)
+		debug("DRAM init failed: %d\n", rv);
+	return rv;
+}
+
+void spl_board_init(void)
+{
+	preloader_console_init();
+	spl_dram_init();
+	arch_cpu_init(); /* to configure mpu for sdram rw permissions */
+}
+
+u32 spl_boot_device(void)
+{
+	return BOOT_DEVICE_MMC1;
+}
+#endif
+
+int board_init(void)
+{
+	gd->bd->bi_boot_params = gd->bd->bi_dram[0].start + 0x100;
+
+	return 0;
+}
diff --git a/board/freescale/ls1043ardb/ddr.c b/board/freescale/ls1043ardb/ddr.c
index 08b43ff5e4c..4d2fce38412 100644
--- a/board/freescale/ls1043ardb/ddr.c
+++ b/board/freescale/ls1043ardb/ddr.c
@@ -114,7 +114,7 @@ dimm_params_t ddr_raw_timing = {
 	.mirrored_dimm = 0,
 	.n_row_addr = 15,
 	.n_col_addr = 10,
-	.bank_addr_bits = 0,
+	.bank_addr_bits = 2,
 	.bank_group_bits = 2,
 	.edc_config = 0,
 	.burst_lengths_bitmask = 0x0c,
diff --git a/board/freescale/p1_p2_rdb_pc/README b/board/freescale/p1_p2_rdb_pc/README
index 86ff04e69d9..f542decec79 100644
--- a/board/freescale/p1_p2_rdb_pc/README
+++ b/board/freescale/p1_p2_rdb_pc/README
@@ -60,5 +60,5 @@ enabled in relative defconfig file,
    CONFIG_RESET_VECTOR_ADDRESS - 0xffc
 
 If device tree support is enabled in defconfig,
-1. use 'u-boot-with-dtb.bin' for NOR boot.
+1. use 'u-boot.bin' for NOR boot.
 2. use 'u-boot-with-spl.bin' for other boot.
diff --git a/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c b/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c
index a71952dcf39..b301491ef81 100644
--- a/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c
+++ b/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c
@@ -83,7 +83,19 @@ struct cpld_data {
 #define CPLD_FXS_LED	0x0F
 #define CPLD_SYS_RST	0x00
 
-void board_reset(void)
+void board_reset_prepare(void)
+{
+	/*
+	 * During reset preparation, turn off external watchdog.
+	 * This ensures that external watchdog does not trigger
+	 * another reset or possible infinite reset loop.
+	 */
+	struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE);
+	out_8(&cpld_data->wd_cfg, CPLD_WD_CFG);
+	in_8(&cpld_data->wd_cfg); /* Read back to sync write */
+}
+
+void board_reset_last(void)
 {
 	struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE);
 	out_8(&cpld_data->system_rst, 1);
@@ -92,12 +104,46 @@ void board_reset(void)
 void board_cpld_init(void)
 {
 	struct cpld_data *cpld_data = (void *)(CONFIG_SYS_CPLD_BASE);
+	u8 prev_wd_cfg = in_8(&cpld_data->wd_cfg);
 
 	out_8(&cpld_data->wd_cfg, CPLD_WD_CFG);
 	out_8(&cpld_data->status_led, CPLD_STATUS_LED);
 	out_8(&cpld_data->fxo_led, CPLD_FXO_LED);
 	out_8(&cpld_data->fxs_led, CPLD_FXS_LED);
+
+	/*
+	 * CPLD's system reset register on P1/P2 RDB boards is not autocleared
+	 * after flipping it. If this register is set to one then CPLD triggers
+	 * reset of CPU in few ms.
+	 *
+	 * CPLD does not trigger reset of CPU for 100ms after the last reset.
+	 *
+	 * This means that trying to reset board via CPLD system reset register
+	 * cause reboot loop. To prevent this reboot loop, the only workaround
+	 * is to try to clear CPLD's system reset register as early as possible
+	 * and it has to be done in 100ms since the last start of reset.
+	 */
 	out_8(&cpld_data->system_rst, CPLD_SYS_RST);
+
+	/*
+	 * If watchdog timer was already set to non-disabled value then it means
+	 * that watchdog timer was already activated, has already expired and
+	 * caused CPU reset. If this happened then due to CPLD firmware bug,
+	 * writing to wd_cfg register has no effect and therefore it is not
+	 * possible to reactivate watchdog timer again. Also if CPU was reset
+	 * via watchdog then some peripherals like i2c do not work. Watchdog and
+	 * i2c start working again after CPU reset via non-watchdog method.
+	 *
+	 * So in case watchdog timer register in CPLD was already enabled then
+	 * disable it in CPLD and reset CPU which cause new boot. Watchdog timer
+	 * is disabled few lines above, after reading CPLD previous value.
+	 * This logic (disabling timer before reset) prevents reboot loop.
+	 */
+	if (prev_wd_cfg != CPLD_WD_CFG) {
+		eieio();
+		do_reset(NULL, 0, 0, NULL);
+		while (1); /* do_reset() does not occur immediately */
+	}
 }
 
 void board_gpio_init(void)
@@ -368,6 +414,24 @@ int board_eth_init(struct bd_info *bis)
 }
 #endif
 
+#if defined(CONFIG_OF_BOARD_SETUP) || defined(CONFIG_OF_BOARD_FIXUP)
+static void fix_max6370_watchdog(void *blob)
+{
+	int off = fdt_node_offset_by_compatible(blob, -1, "maxim,max6370");
+	ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR);
+	u32 gpioval = in_be32(&pgpio->gpdat);
+
+	/*
+	 * Delete watchdog max6370 node in load_default mode (detected by
+	 * GPIO7 - LOAD_DEFAULT_N) because CPLD in load_default mode ignores
+	 * watchdog reset signal. CPLD in load_default mode does not reset
+	 * board when watchdog triggers reset signal.
+	 */
+	if (!(gpioval & BIT(31-7)) && off >= 0)
+		fdt_del_node(blob, off);
+}
+#endif
+
 #ifdef CONFIG_OF_BOARD_SETUP
 int ft_board_setup(void *blob, struct bd_info *bd)
 {
@@ -393,6 +457,8 @@ int ft_board_setup(void *blob, struct bd_info *bd)
 			sizeof("okay"), 0);
 #endif
 
+	fix_max6370_watchdog(blob);
+
 #if defined(CONFIG_HAS_FSL_DR_USB)
 	fsl_fdt_fixup_dr_usb(blob, bd);
 #endif
@@ -444,3 +510,11 @@ int ft_board_setup(void *blob, struct bd_info *bd)
 	return 0;
 }
 #endif
+
+#ifdef CONFIG_OF_BOARD_FIXUP
+int board_fix_fdt(void *blob)
+{
+	fix_max6370_watchdog(blob);
+	return 0;
+}
+#endif
diff --git a/board/freescale/p1_p2_rdb_pc/spl.c b/board/freescale/p1_p2_rdb_pc/spl.c
index b60027ebd9a..eda84bf2b1f 100644
--- a/board/freescale/p1_p2_rdb_pc/spl.c
+++ b/board/freescale/p1_p2_rdb_pc/spl.c
@@ -31,6 +31,12 @@ void board_init_f(ulong bootflag)
 	u32 plat_ratio, bus_clk;
 	ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
 
+	/*
+	 * Call board_early_init_f() as early as possible as it workarounds
+	 * reboot loop due to broken CPLD state machine for reset line.
+	 */
+	board_early_init_f();
+
 	console_init_f();
 
 	/* Set pmuxcr to allow both i2c1 and i2c2 */
diff --git a/board/freescale/p1_p2_rdb_pc/tlb.c b/board/freescale/p1_p2_rdb_pc/tlb.c
index 105d9e38aac..65cedd42a0d 100644
--- a/board/freescale/p1_p2_rdb_pc/tlb.c
+++ b/board/freescale/p1_p2_rdb_pc/tlb.c
@@ -61,11 +61,11 @@ struct fsl_e_tlb_entry tlb_table[] = {
 			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
 			0, 5, BOOKE_PAGESZ_1M, 1),
 #endif
+#endif /* not SPL */
 
 	SET_TLB_ENTRY(1, CONFIG_SYS_CPLD_BASE, CONFIG_SYS_CPLD_BASE_PHYS,
 			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
 			0, 6, BOOKE_PAGESZ_1M, 1),
-#endif /* not SPL */
 
 #ifdef CONFIG_SYS_NAND_BASE
 	/* *I*G - NAND */
diff --git a/board/freescale/p2041rdb/README b/board/freescale/p2041rdb/README
index 79f77e49612..96612daeeb1 100644
--- a/board/freescale/p2041rdb/README
+++ b/board/freescale/p2041rdb/README
@@ -100,9 +100,6 @@ enabled in relative defconfig file,
 3. CONFIG_MPC85XX_HAVE_RESET_VECTOR if reset vector is located at
    CONFIG_RESET_VECTOR_ADDRESS - 0xffc
 
-If device tree support is enabled in defconfig, use 'u-boot-with-dtb.bin'
-instead of u-boot.bin for all boot.
-
 CPLD command
 ============
 The CPLD is used to control the power sequence and some serdes lane
diff --git a/board/freescale/t102xrdb/README b/board/freescale/t102xrdb/README
index 84deb9562a1..de170f52b4d 100644
--- a/board/freescale/t102xrdb/README
+++ b/board/freescale/t102xrdb/README
@@ -267,7 +267,7 @@ enabled in relative defconfig file,
    config_reset_vector_address - 0xffc
 
 if device tree support is enabled in defconfig,
-1. use 'u-boot-with-dtb.bin' for nor boot.
+1. use 'u-boot.bin' for nor boot.
 2. use 'u-boot-with-spl-pbl.bin' for other boot.
 
 2-stage NAND/SPI/SD boot loader
diff --git a/board/freescale/t104xrdb/README b/board/freescale/t104xrdb/README
index 09cb98e33d6..e90dca41663 100644
--- a/board/freescale/t104xrdb/README
+++ b/board/freescale/t104xrdb/README
@@ -382,5 +382,5 @@ enabled in relative defconfig file,
    CONFIG_RESET_VECTOR_ADDRESS - 0xffc
 
 If device tree support is enabled in defconfig,
-1. use 'u-boot-with-dtb.bin' for NOR boot.
+1. use 'u-boot.bin' for NOR boot.
 2. use 'u-boot-with-spl-pbl.bin' for other boot.
diff --git a/board/freescale/t208xqds/README b/board/freescale/t208xqds/README
index 75d317342f6..63953d6b9b6 100755
--- a/board/freescale/t208xqds/README
+++ b/board/freescale/t208xqds/README
@@ -288,5 +288,5 @@ enabled in relative defconfig file,
    CONFIG_RESET_VECTOR_ADDRESS - 0xffc
 
 If device tree support is enabled in defconfig,
-1. use 'u-boot-with-dtb.bin' for NOR boot.
+1. use 'u-boot.bin' for NOR boot.
 2. use 'u-boot-with-spl-pbl.bin' for other boot.
diff --git a/board/freescale/t208xrdb/README b/board/freescale/t208xrdb/README
index c4bfd3b466f..60551f6723e 100644
--- a/board/freescale/t208xrdb/README
+++ b/board/freescale/t208xrdb/README
@@ -284,5 +284,5 @@ enabled in relative defconfig file,
    CONFIG_RESET_VECTOR_ADDRESS - 0xffc
 
 If device tree support is enabled in defconfig,
-1. use 'u-boot-with-dtb.bin' for NOR boot.
+1. use 'u-boot.bin' for NOR boot.
 2. use 'u-boot-with-spl-pbl.bin' for other boot.