diff options
Diffstat (limited to 'board/advantech/dms-ba16/dms-ba16.c')
| -rw-r--r-- | board/advantech/dms-ba16/dms-ba16.c | 630 |
1 files changed, 0 insertions, 630 deletions
diff --git a/board/advantech/dms-ba16/dms-ba16.c b/board/advantech/dms-ba16/dms-ba16.c deleted file mode 100644 index 07a47e9fbb0..00000000000 --- a/board/advantech/dms-ba16/dms-ba16.c +++ /dev/null @@ -1,630 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0+ -/* - * Copyright 2016 Timesys Corporation - * Copyright 2016 Advantech Corporation - * Copyright 2012 Freescale Semiconductor, Inc. - */ - -#include <init.h> -#include <net.h> -#include <asm/arch/clock.h> -#include <asm/arch/imx-regs.h> -#include <asm/arch/iomux.h> -#include <asm/arch/mx6-pins.h> -#include <asm/global_data.h> -#include <linux/delay.h> -#include <linux/errno.h> -#include <asm/gpio.h> -#include <asm/mach-imx/mxc_i2c.h> -#include <asm/mach-imx/iomux-v3.h> -#include <asm/mach-imx/boot_mode.h> -#include <asm/mach-imx/video.h> -#include <mmc.h> -#include <fsl_esdhc_imx.h> -#include <miiphy.h> -#include <netdev.h> -#include <asm/arch/mxc_hdmi.h> -#include <asm/arch/crm_regs.h> -#include <asm/io.h> -#include <asm/arch/sys_proto.h> -#include <i2c.h> -#include <input.h> -#include <pwm.h> -DECLARE_GLOBAL_DATA_PTR; - -#define NC_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ - PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \ - PAD_CTL_HYS) - -#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ - PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \ - PAD_CTL_SRE_FAST | PAD_CTL_HYS) - -#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \ - PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \ - PAD_CTL_SRE_FAST | PAD_CTL_HYS) - -#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \ - PAD_CTL_SPEED_HIGH | PAD_CTL_DSE_48ohm | PAD_CTL_SRE_FAST) - -#define ENET_CLK_PAD_CTRL (PAD_CTL_SPEED_MED | \ - PAD_CTL_DSE_120ohm | PAD_CTL_SRE_FAST) - -#define ENET_RX_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ - PAD_CTL_SPEED_HIGH | PAD_CTL_SRE_FAST) - -#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \ - PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST) - -#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ - PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ - PAD_CTL_ODE | PAD_CTL_SRE_FAST) - -#define I2C_PAD MUX_PAD_CTRL(I2C_PAD_CTRL) - -int dram_init(void) -{ - gd->ram_size = imx_ddr_size(); - - return 0; -} - -static iomux_v3_cfg_t const uart3_pads[] = { - MX6_PAD_EIM_D31__UART3_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL), - MX6_PAD_EIM_D23__UART3_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL), - MX6_PAD_EIM_D24__UART3_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), - MX6_PAD_EIM_D25__UART3_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), -}; - -static iomux_v3_cfg_t const uart4_pads[] = { - MX6_PAD_KEY_COL0__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), - MX6_PAD_KEY_ROW0__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL), -}; - -static iomux_v3_cfg_t const enet_pads[] = { - MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL), - MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL), - MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL), - MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL), - MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL), - MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL), - MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL), - MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL), - MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL), - MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), - MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), - MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), - MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), - MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), - MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_RX_PAD_CTRL), - /* AR8033 PHY Reset */ - MX6_PAD_ENET_TX_EN__GPIO1_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL), -}; - -static void setup_iomux_enet(void) -{ - imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads)); - - /* Reset AR8033 PHY */ - gpio_direction_output(IMX_GPIO_NR(1, 28), 0); - mdelay(10); - gpio_set_value(IMX_GPIO_NR(1, 28), 1); - mdelay(1); -} - -static iomux_v3_cfg_t const usdhc2_pads[] = { - MX6_PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_GPIO_4__GPIO1_IO04 | MUX_PAD_CTRL(NO_PAD_CTRL), -}; - -static iomux_v3_cfg_t const usdhc3_pads[] = { - MX6_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD3_RST__SD3_RESET | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD3_DAT4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD3_DAT5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD3_DAT6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL), -}; - -static iomux_v3_cfg_t const usdhc4_pads[] = { - MX6_PAD_SD4_CLK__SD4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD4_CMD__SD4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD4_DAT4__SD4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD4_DAT5__SD4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD4_DAT6__SD4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD4_DAT7__SD4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_NANDF_CS0__GPIO6_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL), - MX6_PAD_NANDF_CS1__GPIO6_IO14 | MUX_PAD_CTRL(NO_PAD_CTRL), -}; - -static iomux_v3_cfg_t const ecspi1_pads[] = { - MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL), - MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL), - MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL), - MX6_PAD_EIM_EB2__GPIO2_IO30 | MUX_PAD_CTRL(NO_PAD_CTRL), -}; - -static struct i2c_pads_info i2c_pad_info1 = { - .scl = { - .i2c_mode = MX6_PAD_CSI0_DAT9__I2C1_SCL | I2C_PAD, - .gpio_mode = MX6_PAD_CSI0_DAT9__GPIO5_IO27 | I2C_PAD, - .gp = IMX_GPIO_NR(5, 27) - }, - .sda = { - .i2c_mode = MX6_PAD_CSI0_DAT8__I2C1_SDA | I2C_PAD, - .gpio_mode = MX6_PAD_CSI0_DAT8__GPIO5_IO26 | I2C_PAD, - .gp = IMX_GPIO_NR(5, 26) - } -}; - -static struct i2c_pads_info i2c_pad_info2 = { - .scl = { - .i2c_mode = MX6_PAD_KEY_COL3__I2C2_SCL | I2C_PAD, - .gpio_mode = MX6_PAD_KEY_COL3__GPIO4_IO12 | I2C_PAD, - .gp = IMX_GPIO_NR(4, 12) - }, - .sda = { - .i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA | I2C_PAD, - .gpio_mode = MX6_PAD_KEY_ROW3__GPIO4_IO13 | I2C_PAD, - .gp = IMX_GPIO_NR(4, 13) - } -}; - -static struct i2c_pads_info i2c_pad_info3 = { - .scl = { - .i2c_mode = MX6_PAD_GPIO_3__I2C3_SCL | I2C_PAD, - .gpio_mode = MX6_PAD_GPIO_3__GPIO1_IO03 | I2C_PAD, - .gp = IMX_GPIO_NR(1, 3) - }, - .sda = { - .i2c_mode = MX6_PAD_GPIO_6__I2C3_SDA | I2C_PAD, - .gpio_mode = MX6_PAD_GPIO_6__GPIO1_IO06 | I2C_PAD, - .gp = IMX_GPIO_NR(1, 6) - } -}; - -#ifdef CONFIG_MXC_SPI -int board_spi_cs_gpio(unsigned bus, unsigned cs) -{ - return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(2, 30)) : -1; -} - -static void setup_spi(void) -{ - imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads)); -} -#endif - -static iomux_v3_cfg_t const pcie_pads[] = { - MX6_PAD_GPIO_5__GPIO1_IO05 | MUX_PAD_CTRL(NO_PAD_CTRL), - MX6_PAD_GPIO_17__GPIO7_IO12 | MUX_PAD_CTRL(NO_PAD_CTRL), -}; - -static void setup_pcie(void) -{ - imx_iomux_v3_setup_multiple_pads(pcie_pads, ARRAY_SIZE(pcie_pads)); -} - -static void setup_iomux_uart(void) -{ - imx_iomux_v3_setup_multiple_pads(uart3_pads, ARRAY_SIZE(uart3_pads)); - imx_iomux_v3_setup_multiple_pads(uart4_pads, ARRAY_SIZE(uart4_pads)); -} - -#ifdef CONFIG_FSL_ESDHC_IMX -struct fsl_esdhc_cfg usdhc_cfg[3] = { - {USDHC2_BASE_ADDR}, - {USDHC3_BASE_ADDR}, - {USDHC4_BASE_ADDR}, -}; - -#define USDHC2_CD_GPIO IMX_GPIO_NR(1, 4) -#define USDHC4_CD_GPIO IMX_GPIO_NR(6, 11) - -int board_mmc_getcd(struct mmc *mmc) -{ - struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; - int ret = 0; - - switch (cfg->esdhc_base) { - case USDHC2_BASE_ADDR: - ret = !gpio_get_value(USDHC2_CD_GPIO); - break; - case USDHC3_BASE_ADDR: - ret = 1; /* eMMC is always present */ - break; - case USDHC4_BASE_ADDR: - ret = !gpio_get_value(USDHC4_CD_GPIO); - break; - } - - return ret; -} - -int board_mmc_init(struct bd_info *bis) -{ - int ret; - int i; - - for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) { - switch (i) { - case 0: - imx_iomux_v3_setup_multiple_pads( - usdhc2_pads, ARRAY_SIZE(usdhc2_pads)); - gpio_direction_input(USDHC2_CD_GPIO); - usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK); - break; - case 1: - imx_iomux_v3_setup_multiple_pads( - usdhc3_pads, ARRAY_SIZE(usdhc3_pads)); - usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); - break; - case 2: - imx_iomux_v3_setup_multiple_pads( - usdhc4_pads, ARRAY_SIZE(usdhc4_pads)); - gpio_direction_input(USDHC4_CD_GPIO); - usdhc_cfg[2].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK); - break; - default: - printf("Warning: you configured more USDHC controllers\n" - "(%d) then supported by the board (%d)\n", - i + 1, CONFIG_SYS_FSL_USDHC_NUM); - return -EINVAL; - } - - ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]); - if (ret) - return ret; - } - - return 0; -} -#endif - -static int mx6_rgmii_rework(struct phy_device *phydev) -{ - /* set device address 0x7 */ - phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7); - /* offset 0x8016: CLK_25M Clock Select */ - phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016); - /* enable register write, no post increment, address 0x7 */ - phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007); - /* set to 125 MHz from local PLL source */ - phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x18); - /* set debug port address: SerDes Test and System Mode Control */ - phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05); - /* enable rgmii tx clock delay */ - /* set the reserved bits to avoid board specific voltage peak issue*/ - phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x3D47); - - return 0; -} - -int board_phy_config(struct phy_device *phydev) -{ - mx6_rgmii_rework(phydev); - - if (phydev->drv->config) - phydev->drv->config(phydev); - - return 0; -} - -#if defined(CONFIG_VIDEO_IPUV3) -static iomux_v3_cfg_t const backlight_pads[] = { - /* Power for LVDS Display */ - MX6_PAD_EIM_D22__GPIO3_IO22 | MUX_PAD_CTRL(NO_PAD_CTRL), -#define LVDS_POWER_GP IMX_GPIO_NR(3, 22) - /* Backlight enable for LVDS display */ - MX6_PAD_GPIO_0__GPIO1_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL), -#define LVDS_BACKLIGHT_GP IMX_GPIO_NR(1, 0) - /* backlight PWM brightness control */ - MX6_PAD_SD1_DAT3__PWM1_OUT | MUX_PAD_CTRL(NO_PAD_CTRL), -}; - -static void do_enable_hdmi(struct display_info_t const *dev) -{ - imx_enable_hdmi_phy(); -} - -int board_cfb_skip(void) -{ - gpio_direction_output(LVDS_POWER_GP, 1); - - return 0; -} - -static int detect_baseboard(struct display_info_t const *dev) -{ - return 0 == dev->addr; -} - -struct display_info_t const displays[] = {{ - .bus = -1, - .addr = 0, - .pixfmt = IPU_PIX_FMT_RGB24, - .detect = detect_baseboard, - .enable = NULL, - .mode = { - .name = "SHARP-LQ156M1LG21", - .refresh = 60, - .xres = 1920, - .yres = 1080, - .pixclock = 7851, - .left_margin = 100, - .right_margin = 40, - .upper_margin = 30, - .lower_margin = 3, - .hsync_len = 10, - .vsync_len = 2, - .sync = FB_SYNC_EXT, - .vmode = FB_VMODE_NONINTERLACED -} }, { - .bus = -1, - .addr = 3, - .pixfmt = IPU_PIX_FMT_RGB24, - .detect = detect_hdmi, - .enable = do_enable_hdmi, - .mode = { - .name = "HDMI", - .refresh = 60, - .xres = 1024, - .yres = 768, - .pixclock = 15385, - .left_margin = 220, - .right_margin = 40, - .upper_margin = 21, - .lower_margin = 7, - .hsync_len = 60, - .vsync_len = 10, - .sync = FB_SYNC_EXT, - .vmode = FB_VMODE_NONINTERLACED -} } }; -size_t display_count = ARRAY_SIZE(displays); - -static void setup_display(void) -{ - struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; - struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR; - - clrbits_le32(&mxc_ccm->cscmr2, MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV); - - imx_setup_hdmi(); - - /* Set LDB_DI0 as clock source for IPU_DI0 */ - clrsetbits_le32(&mxc_ccm->chsccdr, - MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK, - (CHSCCDR_CLK_SEL_LDB_DI0 << - MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET)); - - /* Turn on IPU LDB DI0 clocks */ - setbits_le32(&mxc_ccm->CCGR3, MXC_CCM_CCGR3_LDB_DI0_MASK); - - enable_ipu_clock(); - - writel(IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES | - IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_HIGH | - IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW | - IOMUXC_GPR2_BIT_MAPPING_CH1_SPWG | - IOMUXC_GPR2_DATA_WIDTH_CH1_24BIT | - IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG | - IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT | - IOMUXC_GPR2_SPLIT_MODE_EN_MASK | - IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0 | - IOMUXC_GPR2_LVDS_CH1_MODE_ENABLED_DI0, - &iomux->gpr[2]); - - clrsetbits_le32(&iomux->gpr[3], - IOMUXC_GPR3_LVDS0_MUX_CTL_MASK | - IOMUXC_GPR3_LVDS1_MUX_CTL_MASK | - IOMUXC_GPR3_HDMI_MUX_CTL_MASK, - (IOMUXC_GPR3_MUX_SRC_IPU1_DI0 << - IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET)); - - /* backlights off until needed */ - imx_iomux_v3_setup_multiple_pads(backlight_pads, - ARRAY_SIZE(backlight_pads)); - - gpio_direction_input(LVDS_POWER_GP); - gpio_direction_input(LVDS_BACKLIGHT_GP); -} -#endif /* CONFIG_VIDEO_IPUV3 */ - -/* - * Do not overwrite the console - * Use always serial for U-Boot console - */ -int overwrite_console(void) -{ - return 1; -} - -int board_eth_init(struct bd_info *bis) -{ - setup_iomux_enet(); - setup_pcie(); - - return cpu_eth_init(bis); -} - -static iomux_v3_cfg_t const misc_pads[] = { - MX6_PAD_KEY_ROW2__GPIO4_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL), - MX6_PAD_EIM_A25__GPIO5_IO02 | MUX_PAD_CTRL(NC_PAD_CTRL), - MX6_PAD_EIM_CS0__GPIO2_IO23 | MUX_PAD_CTRL(NC_PAD_CTRL), - MX6_PAD_EIM_CS1__GPIO2_IO24 | MUX_PAD_CTRL(NC_PAD_CTRL), - MX6_PAD_EIM_OE__GPIO2_IO25 | MUX_PAD_CTRL(NC_PAD_CTRL), - MX6_PAD_EIM_BCLK__GPIO6_IO31 | MUX_PAD_CTRL(NC_PAD_CTRL), - MX6_PAD_GPIO_1__GPIO1_IO01 | MUX_PAD_CTRL(NC_PAD_CTRL), -}; -#define SUS_S3_OUT IMX_GPIO_NR(4, 11) -#define WIFI_EN IMX_GPIO_NR(6, 14) - -int setup_ba16_sata(void) -{ - struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR; - int ret; - - ret = enable_sata_clock(); - if (ret) - return ret; - - clrsetbits_le32(&iomuxc_regs->gpr[13], - IOMUXC_GPR13_SATA_MASK, - IOMUXC_GPR13_SATA_PHY_8_RXEQ_3P0DB - |IOMUXC_GPR13_SATA_PHY_7_SATA2M - |IOMUXC_GPR13_SATA_SPEED_3G - |(1<<IOMUXC_GPR13_SATA_PHY_6_SHIFT) - |IOMUXC_GPR13_SATA_SATA_PHY_5_SS_DISABLED - |IOMUXC_GPR13_SATA_SATA_PHY_4_ATTEN_12_16 - |IOMUXC_GPR13_SATA_PHY_3_TXBOOST_3P33_DB - |IOMUXC_GPR13_SATA_PHY_2_TX_1P133V - |IOMUXC_GPR13_SATA_PHY_1_SLOW); - - return 0; -} - -int board_early_init_f(void) -{ - imx_iomux_v3_setup_multiple_pads(misc_pads, - ARRAY_SIZE(misc_pads)); - - setup_iomux_uart(); - -#if defined(CONFIG_VIDEO_IPUV3) - /* Set LDB clock to PLL2 PFD0 */ - select_ldb_di_clock_source(MXC_PLL2_PFD0_CLK); -#endif - return 0; -} - -int board_init(void) -{ - gpio_direction_output(SUS_S3_OUT, 1); - gpio_direction_output(WIFI_EN, 1); -#if defined(CONFIG_VIDEO_IPUV3) - setup_display(); -#endif - /* address of boot parameters */ - gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; - -#ifdef CONFIG_MXC_SPI - setup_spi(); -#endif - setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1); - setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2); - setup_i2c(3, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info3); - - return 0; -} - -#ifdef CONFIG_CMD_BMODE -static const struct boot_mode board_boot_modes[] = { - /* 4 bit bus width */ - {"sd2", MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)}, - {"sd3", MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)}, - {NULL, 0}, -}; -#endif - -void pmic_init(void) -{ - -#define DA9063_ADDR 0x58 -#define BCORE2_CONF 0x9D -#define BCORE1_CONF 0x9E -#define BPRO_CONF 0x9F -#define BIO_CONF 0xA0 -#define BMEM_CONF 0xA1 -#define BPERI_CONF 0xA2 -#define MODE_BIT_H 7 -#define MODE_BIT_L 6 - - uchar val; - i2c_set_bus_num(2); - - i2c_read(DA9063_ADDR, BCORE2_CONF, 1, &val, 1); - val |= (1 << MODE_BIT_H); - val &= ~(1 << MODE_BIT_L); - i2c_write(DA9063_ADDR, BCORE2_CONF , 1, &val, 1); - - i2c_read(DA9063_ADDR, BCORE1_CONF, 1, &val, 1); - val |= (1 << MODE_BIT_H); - val &= ~(1 << MODE_BIT_L); - i2c_write(DA9063_ADDR, BCORE1_CONF , 1, &val, 1); - - i2c_read(DA9063_ADDR, BPRO_CONF, 1, &val, 1); - val |= (1 << MODE_BIT_H); - val &= ~(1 << MODE_BIT_L); - i2c_write(DA9063_ADDR, BPRO_CONF , 1, &val, 1); - - i2c_read(DA9063_ADDR, BIO_CONF, 1, &val, 1); - val |= (1 << MODE_BIT_H); - val &= ~(1 << MODE_BIT_L); - i2c_write(DA9063_ADDR, BIO_CONF , 1, &val, 1); - - i2c_read(DA9063_ADDR, BMEM_CONF, 1, &val, 1); - val |= (1 << MODE_BIT_H); - val &= ~(1 << MODE_BIT_L); - i2c_write(DA9063_ADDR, BMEM_CONF , 1, &val, 1); - - i2c_read(DA9063_ADDR, BPERI_CONF, 1, &val, 1); - val |= (1 << MODE_BIT_H); - val &= ~(1 << MODE_BIT_L); - i2c_write(DA9063_ADDR, BPERI_CONF , 1, &val, 1); - -} - -int board_late_init(void) -{ -#ifdef CONFIG_CMD_BMODE - add_board_boot_modes(board_boot_modes); -#endif - -#if defined(CONFIG_VIDEO_IPUV3) - /* - * We need at least 200ms between power on and backlight on - * as per specifications from CHI MEI - */ - mdelay(250); - - /* enable backlight PWM 1 */ - pwm_init(0, 0, 0); - - /* duty cycle 5000000ns, period: 5000000ns */ - pwm_config(0, 5000000, 5000000); - - /* Backlight Power */ - gpio_direction_output(LVDS_BACKLIGHT_GP, 1); - - pwm_enable(0); -#endif - -#ifdef CONFIG_SATA - setup_ba16_sata(); -#endif - - /* board specific pmic init */ - pmic_init(); - - return 0; -} - -int checkboard(void) -{ - printf("BOARD: %s\n", CONFIG_BOARD_NAME); - return 0; -} |