aboutsummaryrefslogtreecommitdiffstats
path: root/configs/ls1088aqds_qspi_defconfig
Commit message (Collapse)AuthorAgeFilesLines
* configs: layerscape: delete defconfigs using legacy PPA secure FWLaurentiu Tudor2023-10-101-108/+0
| | | | | | | | | | PPA was a secure firmware developed in-house which is no longer supported and replaced by TF-A quite some years ago. This makes the defconfigs that make use of PPA obsolete, so remove them. Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> [Merged part 1 and part 2] Signed-off-by: Peng Fan <peng.fan@nxp.com>
* configs: Resync with savedefconfigTom Rini2023-10-021-2/+2
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Resync with savedefconfigTom Rini2023-05-011-1/+1
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Resync with savedefconfigTom Rini2023-03-271-1/+1
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Resync with savedefconfigTom Rini2023-02-171-2/+2
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_SYS_NS16550_MEM32 et al to KconfigTom Rini2022-12-051-1/+1
| | | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_SPL_NS16550_MIN_FUNCTIONS CONFIG_SYS_NS16550_MEM32 CONFIG_SYS_NS16550_PORT_MAPPED CONFIG_SYS_NS16550_REG_SIZE CONFIG_SYS_NS16550_SERIAL To do this we also introduce CONFIG_SPL_SYS_NS16550_SERIAL so that platforms can enable the legacy driver here for SPL. Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_SYS_NAND_MAX_OOBFREE et al to KconfigTom Rini2022-12-051-0/+2
| | | | | | | | | This converts the following to Kconfig: CONFIG_SYS_NAND_MAX_OOBFREE CONFIG_SYS_NAND_MAX_ECCPOS Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* Rename CONFIG_SYS_TEXT_BASE to CONFIG_TEXT_BASESimon Glass2022-10-311-1/+1
| | | | | | | | | The current name is inconsistent with SPL which uses CONFIG_SPL_TEXT_BASE and this makes it imposible to use CONFIG_VAL(). Rename it to resolve this problem. Signed-off-by: Simon Glass <sjg@chromium.org>
* configs: Resync with savedefconfigWIP/2022-10-21-enforce-some-DM-migrationsTom Rini2022-10-211-1/+0
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_SYS_FSL_NUM_CC_PLLS to KconfigTom Rini2022-08-121-0/+1
| | | | | | | This converts the following to Kconfig: CONFIG_SYS_FSL_NUM_CC_PLLS Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_FSL_MEMAC et al to KconfigTom Rini2022-08-041-0/+2
| | | | | | | | This converts the following to Kconfig: CONFIG_FSL_MEMAC CONFIG_SYS_MEMAC_LITTLE_ENDIAN Signed-off-by: Tom Rini <trini@konsulko.com>
* Merge branch '2022-07-07-Kconfig-migrations-dead-code-removal' into nextTom Rini2022-07-071-5/+4
| | | | | - Migrate more CONFIG options to Kconfig and remove some unused code while we're at it.
* Convert CONFIG_ESDHC_DETECT_QUIRK to KconfigTom Rini2022-07-051-0/+1
| | | | | | | This converts the following to Kconfig: CONFIG_ESDHC_DETECT_QUIRK Signed-off-by: Tom Rini <trini@konsulko.com>
* Migrate CUSTOM_SYS_INIT_SP_ADDR to Kconfig using system-constants.hTom Rini2022-06-061-0/+2
| | | | | | | | | | | | | | - Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR - Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack pointer directly, otherwise we use the common calculation. - On some platforms that were using the standard calculation but did not set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them. - On a small number of platforms that were not subtracting GENERATED_GBL_DATA_SIZE do so now via the standard calculation. - CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most board config header files. Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_SYS_PBSIZE to KconfigTom Rini2022-06-061-0/+1
| | | | | | | This converts the following to Kconfig: CONFIG_SYS_PBSIZE Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_SYS_MAXARGS to KconfigTom Rini2022-06-061-0/+1
| | | | | | | This converts the following to Kconfig: CONFIG_SYS_MAXARGS Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Resync with savedefconfigTom Rini2022-04-081-1/+1
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_FSL_QIXIS et al to KconfigTom Rini2022-04-081-0/+1
| | | | | | | | This converts the following to Kconfig: CONFIG_FSL_QIXIS CONFIG_QIXIS_I2C_ACCESS Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Resync with savedefconfigTom Rini2022-04-011-2/+2
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_RESET_PHY_R to KconfigTom Rini2022-03-251-0/+1
| | | | | | | | This converts the following to Kconfig: CONFIG_RESET_PHY_R Cc: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_ETHPRIME to KconfigTom Rini2022-03-181-0/+2
| | | | | | | | | | | This converts the following to Kconfig: CONFIG_ETHPRIME This is also done by adding a gating Kconfig option, CONFIG_USE_ETHPRIME similar to other options that are not always set and control environment variables. Signed-off-by: Tom Rini <trini@konsulko.com>
* nvme: Split out PCI supportMark Kettenis2022-02-101-1/+1
| | | | | | | | | | | | | Apple SoCs have an integrated NVMe controller that isn't connected over a PCIe bus. In preparation for adding support for this NVMe controller, split out the PCI support into its own file. This file is selected through a new CONFIG_NVME_PCI Kconfig option, so do a wholesale replacement of CONFIG_NVME with CONFIG_NVME_PCI. Signed-off-by: Mark Kettenis <kettenis@openbsd.org> Reviewed-by: Simon Glass <sjg@chromium.org> Tested on: Macbook Air M1 Tested-by: Simon Glass <sjg@chromium.org>
* configs: Resync with savedefconfigTom Rini2022-02-091-1/+1
| | | | | | | Rsync all defconfig files using moveconfig.py and update scripts/pylint.base Signed-off-by: Tom Rini <trini@konsulko.com>
* sata: Rearrange Kconfig for SATASimon Glass2022-02-091-0/+1
| | | | | | | | | Move the SATA options inside an 'if SATA' part, so they are grouped. Fix the 'Complient' typo while we are here. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de>
* Convert CONFIG_REMAKE_ELF to KconfigAlper Nebi Yasak2022-02-091-0/+1
| | | | | | | This converts the following to Kconfig: CONFIG_REMAKE_ELF Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
* configs: Resync with savedefconfigTom Rini2022-01-241-1/+1
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* Finish CONFIG_VID et al conversion to KconfigTom Rini2021-12-271-0/+5
| | | | | | | | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_VID CONFIG_VOL_MONITOR_INA220 CONFIG_VOL_MONITOR_IR36021_READ CONFIG_VOL_MONITOR_IR36021_SET CONFIG_VOL_MONITOR_LTC3882_READ CONFIG_VOL_MONITOR_LTC3882_SET To finish this migration, we first need to introduce CONFIG_SPL_VID as some platforms only use this code in full U-Boot while others use it in SPL as well. To make the Kconfig logic clearer, guard all of the sub-options with a if VID || SPL_VID check. Finally, add Kconfig options for the remaining related options that did not previously have one. Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_CONS_INDEX et al to KconfigTom Rini2021-12-271-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This converts the following to Kconfig: CONFIG_CONS_INDEX CONFIG_DEBUG_UART_CLOCK CONFIG_FSL_TZPC_BP147 CONFIG_GENERIC_ATMEL_MCI CONFIG_IDENT_STRING CONFIG_LIBATA CONFIG_LNX_KRNL_IMG_TEXT_OFFSET_BASE CONFIG_LPC32XX_GPIO CONFIG_MP CONFIG_MPC8XXX_GPIO CONFIG_MTD_PARTITIONS CONFIG_MVGBE CONFIG_MXC_GPIO CONFIG_NR_DRAM_BANKS CONFIG_OF_BOARD_SETUP CONFIG_OF_STDOUT_VIA_ALIAS CONFIG_OF_SYSTEM_SETUP CONFIG_PREBOOT CONFIG_ROCKCHIP_SERIAL CONFIG_RTC_ENABLE_32KHZ_OUTPUT CONFIG_RTC_MV CONFIG_SCSI_AHCI CONFIG_SF_DEFAULT_BUS CONFIG_SF_DEFAULT_CS CONFIG_SF_DEFAULT_SPEED CONFIG_SOFT_SPI CONFIG_SPI_FLASH_EON CONFIG_SPI_FLASH_MACRONIX CONFIG_SPI_FLASH_MTD CONFIG_SPI_FLASH_SPANSION CONFIG_SPI_FLASH_SST CONFIG_SPI_FLASH_STMICRO CONFIG_SUPPORT_RAW_INITRD CONFIG_SYS_ARCH_TIMER CONFIG_SYS_BOARD CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE CONFIG_SYS_DCACHE_OFF CONFIG_SYS_FDT_SAVE_ADDRESS CONFIG_SYS_FLASH_CFI CONFIG_SYS_FSL_ERRATUM_ESDHC135 CONFIG_SYS_HAS_SERDES CONFIG_SYS_L2CACHE_OFF CONFIG_SYS_LITTLE_ENDIAN CONFIG_SYS_LOAD_ADDR CONFIG_SYS_MMCSD_FS_BOOT_PARTITION CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR CONFIG_SYS_NS16550 CONFIG_SYS_PLLFIN CONFIG_SYS_SPI_U_BOOT_OFFS CONFIG_TIMER_SYS_TICK_CH CONFIG_USB_EHCI_FSL CONFIG_U_QE CONFIG_VERSION_VARIABLE Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_USE_BOOTCOMMAND et al to KconfigTom Rini2021-12-011-1/+1
| | | | | | | | | | This converts the following to Kconfig: CONFIG_USE_BOOTCOMMAND CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND CONFIG_NFSBOOTCOMMAND Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_PHYLIB et al to KconfigTom Rini2021-11-121-0/+1
| | | | | | | | | | This converts the following to Kconfig: CONFIG_PHYLIB CONFIG_PHY_ATHEROS CONFIG_PHY_GIGE CONFIG_MII Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Resync with savedefconfigWIP/01Nov2021Tom Rini2021-11-011-2/+1
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_NAND_FSL_ELBC et al to KconfigTom Rini2021-10-061-0/+1
| | | | | | | | | | | | This converts the following to Kconfig: CONFIG_NAND_FSL_ELBC CONFIG_NAND_FSL_IFC Note that a number of PowerPC platforms had previously enabled CONFIG_NAND_FSL_ELBC without CONFIG_MTD_RAW_NAND, and now they no longer enable the option, reducing the size of a few functions. Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_SYS_NAND_ONFI_DETECTION to KconfigTom Rini2021-10-061-0/+1
| | | | | | | This converts the following to Kconfig: CONFIG_SYS_NAND_ONFI_DETECTION Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_SYS_MALLOC_LEN to KconfigTom Rini2021-08-311-0/+1
| | | | | | | | | This converts the following to Kconfig: CONFIG_SYS_MALLOC_LEN Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Sean Anderson <seanga2@gmail.com> Reviewed-by: Rick Chen <rick@andestech.com>
* Convert CONFIG_QSPI_BOOT to KconfigTom Rini2021-08-311-1/+1
| | | | | | | This converts the following to Kconfig: CONFIG_QSPI_BOOT Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_SYS_FSL_DDR4 to KconfigTom Rini2021-08-311-1/+1
| | | | | | | This converts the following to Kconfig: CONFIG_SYS_FSL_DDR4 Signed-off-by: Tom Rini <trini@konsulko.com>
* nxp: Migrate a number of DDR related symbols to KconfigTom Rini2021-08-311-0/+2
| | | | | | | | | | - Guard most of the options in drivers/ddr/fsl/Kconfig with SYS_FSL_DDR || SYS_FSL_MMDC. - Migrate FSL_DMA, DDR_ECC, DDR_ECC_CMD, and ECC_INIT_VIA_DDRCONTROLLER to Kconfig. - Clean up the logic for including the DDR_ECC_CMD code. Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_SYS_I2C_LEGACY to Kconfig and add CONFIG_[ST]PL_SYS_I2C_LEGACYTom Rini2021-08-301-0/+1
| | | | | | | | | | | First, we convert CONFIG_SYS_I2C_LEGACY to Kconfig. Next, as you cannot have SYS_I2C_LEGACY and DM_I2C at the same time, introduce CONFIG_SPL_SYS_I2C_LEGACY so that we can enable the legacy option only in SPL. Finally, for some PowerPC cases we also need CONFIG_TPL_SYS_I2C_LEGACY support. Convert all of the existing users to one or more symbols. Signed-off-by: Tom Rini <trini@konsulko.com>
* Convert CONFIG_SYS_I2C_EEPROM_ADDR et al to KconfigTom Rini2021-08-301-0/+2
| | | | | | | | | | | | | - Rename usages of CONFIG_SYS_DEF_EEPROM_ADDR to CONFIG_SYS_I2C_EEPROM_ADDR based on current usage. - Convert CONFIG_SYS_I2C_EEPROM_ADDR, CONFIG_SYS_I2C_EEPROM_ADDR_LEN, CONFIG_SYS_I2C_EEPROM_BUS, CONFIG_CONFIG_SYS_EEPROM_SIZE CONFIG_SYS_EEPROM_PAGE_WRITE_BITS and CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS to Kconfig. We move these symbols around a bit and add appropriate dependencies to them. In some cases, we now add a correct default value as well. Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Resync with savedefconfigTom Rini2021-07-261-3/+1
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* board: freescale: ls1088a: Update I2C mux configStephen Carlson2021-07-201-0/+1
| | | | | | | Updates the board configuration to enable use of the PCA9547 I2C mux. Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
* configs: Resync with savedefconfigTom Rini2021-06-281-1/+1
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Resync with savedefconfigTom Rini2021-05-111-1/+0
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Resync with savedefconfigTom Rini2021-02-151-1/+1
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: ls1088aqds: enable DM_GPIO and CMD_GPIOBiwen Li2021-02-081-0/+2
| | | | | | | Enable DM_GPIO and CMD_GPIO for board ls1088aqds Signed-off-by: Biwen Li <biwen.li@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
* configs: Resync with savedefconfigTom Rini2020-11-301-2/+2
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Resync with savedefconfigTom Rini2020-10-291-2/+1
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: ls1088a: enable CMD_MDIOIoana Ciornei2020-10-231-1/+0
| | | | | | | | Enable the CMD_MDIO Kconfig option by removing the "is not set" indication from all the defconfigs for this SoC. Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
* configs: Enable NVME support for Layerscape platformsWasim Khan2020-10-231-0/+2
| | | | | | | | Enable CONFIG_NVME and CONFIG_CMD_NVME for Layerscape platforms Signed-off-by: Wasim Khan <wasim.khan@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
* configs: Resync with savedefconfigv2020.10-rc2Tom Rini2020-08-101-1/+1
| | | | | | Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
generated by cgit (git 2.34.1) at 2025-02-28 08:43:21 +0000