[ethernet] Update mii.h and use it in drivers that had a private copy

Signed-off-by: Michael Brown <mcb30@etherboot.org>

1 files changed, 0 insertions, 107 deletions

diff --git a/src/drivers/net/bnx2.h b/src/drivers/net/bnx2.h
index b853a694..92678680 100644
--- a/src/drivers/net/bnx2.h
+++ b/src/drivers/net/bnx2.h
@@ -92,113 +92,6 @@ typedef int pci_power_t;
 #define WAKE_MAGIC		(1 << 5)
 #define WAKE_MAGICSECURE	(1 << 6) /* only meaningful if WAKE_MAGIC */
 
-/* Generic MII registers. */
-
-#define MII_BMCR            0x00        /* Basic mode control register */
-#define MII_BMSR            0x01        /* Basic mode status register  */
-#define MII_PHYSID1         0x02        /* PHYS ID 1                   */
-#define MII_PHYSID2         0x03        /* PHYS ID 2                   */
-#define MII_ADVERTISE       0x04        /* Advertisement control reg   */
-#define MII_LPA             0x05        /* Link partner ability reg    */
-#define MII_EXPANSION       0x06        /* Expansion register          */
-#define MII_CTRL1000        0x09        /* 1000BASE-T control          */
-#define MII_STAT1000        0x0a        /* 1000BASE-T status           */
-#define MII_DCOUNTER        0x12        /* Disconnect counter          */
-#define MII_FCSCOUNTER      0x13        /* False carrier counter       */
-#define MII_NWAYTEST        0x14        /* N-way auto-neg test reg     */
-#define MII_RERRCOUNTER     0x15        /* Receive error counter       */
-#define MII_SREVISION       0x16        /* Silicon revision            */
-#define MII_RESV1           0x17        /* Reserved...                 */
-#define MII_LBRERROR        0x18        /* Lpback, rx, bypass error    */
-#define MII_PHYADDR         0x19        /* PHY address                 */
-#define MII_RESV2           0x1a        /* Reserved...                 */
-#define MII_TPISTATUS       0x1b        /* TPI status for 10mbps       */
-#define MII_NCONFIG         0x1c        /* Network interface config    */
-
-/* Basic mode control register. */
-#define BMCR_RESV               0x007f  /* Unused...                   */
-#define BMCR_SPEED1000		0x0040  /* MSB of Speed (1000)         */
-#define BMCR_CTST               0x0080  /* Collision test              */
-#define BMCR_FULLDPLX           0x0100  /* Full duplex                 */
-#define BMCR_ANRESTART          0x0200  /* Auto negotiation restart    */
-#define BMCR_ISOLATE            0x0400  /* Disconnect DP83840 from MII */
-#define BMCR_PDOWN              0x0800  /* Powerdown the DP83840       */
-#define BMCR_ANENABLE           0x1000  /* Enable auto negotiation     */
-#define BMCR_SPEED100           0x2000  /* Select 100Mbps              */
-#define BMCR_LOOPBACK           0x4000  /* TXD loopback bits           */
-#define BMCR_RESET              0x8000  /* Reset the DP83840           */
-
-/* Basic mode status register. */
-#define BMSR_ERCAP              0x0001  /* Ext-reg capability          */
-#define BMSR_JCD                0x0002  /* Jabber detected             */
-#define BMSR_LSTATUS            0x0004  /* Link status                 */
-#define BMSR_ANEGCAPABLE        0x0008  /* Able to do auto-negotiation */
-#define BMSR_RFAULT             0x0010  /* Remote fault detected       */
-#define BMSR_ANEGCOMPLETE       0x0020  /* Auto-negotiation complete   */
-#define BMSR_RESV               0x07c0  /* Unused...                   */
-#define BMSR_10HALF             0x0800  /* Can do 10mbps, half-duplex  */
-#define BMSR_10FULL             0x1000  /* Can do 10mbps, full-duplex  */
-#define BMSR_100HALF            0x2000  /* Can do 100mbps, half-duplex */
-#define BMSR_100FULL            0x4000  /* Can do 100mbps, full-duplex */
-#define BMSR_100BASE4           0x8000  /* Can do 100mbps, 4k packets  */
-
-/* Advertisement control register. */
-#define ADVERTISE_SLCT          0x001f  /* Selector bits               */
-#define ADVERTISE_CSMA          0x0001  /* Only selector supported     */
-#define ADVERTISE_10HALF        0x0020  /* Try for 10mbps half-duplex  */
-#define ADVERTISE_10FULL        0x0040  /* Try for 10mbps full-duplex  */
-#define ADVERTISE_100HALF       0x0080  /* Try for 100mbps half-duplex */
-#define ADVERTISE_100FULL       0x0100  /* Try for 100mbps full-duplex */
-#define ADVERTISE_100BASE4      0x0200  /* Try for 100mbps 4k packets  */
-#define ADVERTISE_RESV          0x1c00  /* Unused...                   */
-#define ADVERTISE_RFAULT        0x2000  /* Say we can detect faults    */
-#define ADVERTISE_LPACK         0x4000  /* Ack link partners response  */
-#define ADVERTISE_NPAGE         0x8000  /* Next page bit               */
-#define ADVERTISE_1000XFULL     0x0020  /* Try for 1000BASE-X full-duplex */
-#define ADVERTISE_10FULL        0x0040  /* Try for 10mbps full-duplex  */
-#define ADVERTISE_1000XHALF     0x0040  /* Try for 1000BASE-X half-duplex */
-#define ADVERTISE_1000XPAUSE    0x0080  /* Try for 1000BASE-X pause    */
-#define ADVERTISE_PAUSE_CAP     0x0400  /* Try for pause               */
-#define ADVERTISE_1000XPSE_ASYM 0x0100  /* Try for 1000BASE-X asym pause */
-#define ADVERTISE_PAUSE_ASYM    0x0800  /* Try for asymetric pause     */
-
-#define ADVERTISE_FULL (ADVERTISE_100FULL | ADVERTISE_10FULL | \
-			ADVERTISE_CSMA)
-#define ADVERTISE_ALL (ADVERTISE_10HALF | ADVERTISE_10FULL | \
-                       ADVERTISE_100HALF | ADVERTISE_100FULL)
-
-/* Link partner ability register. */
-#define LPA_SLCT                0x001f  /* Same as advertise selector  */
-#define LPA_10HALF              0x0020  /* Can do 10mbps half-duplex   */
-#define LPA_10FULL              0x0040  /* Can do 10mbps full-duplex   */
-#define LPA_100HALF             0x0080  /* Can do 100mbps half-duplex  */
-#define LPA_100FULL             0x0100  /* Can do 100mbps full-duplex  */
-#define LPA_100BASE4            0x0200  /* Can do 100mbps 4k packets   */
-#define LPA_RESV                0x1c00  /* Unused...                   */
-#define LPA_RFAULT              0x2000  /* Link partner faulted        */
-#define LPA_LPACK               0x4000  /* Link partner acked us       */
-#define LPA_NPAGE               0x8000  /* Next page bit               */
-
-#define LPA_DUPLEX		(LPA_10FULL | LPA_100FULL)
-#define LPA_100			(LPA_100FULL | LPA_100HALF | LPA_100BASE4)
-
-/* Expansion register for auto-negotiation. */
-#define EXPANSION_NWAY          0x0001  /* Can do N-way auto-nego      */
-#define EXPANSION_LCWP          0x0002  /* Got new RX page code word   */
-#define EXPANSION_ENABLENPAGE   0x0004  /* This enables npage words    */
-#define EXPANSION_NPCAPABLE     0x0008  /* Link partner supports npage */
-#define EXPANSION_MFAULTS       0x0010  /* Multiple faults detected    */
-#define EXPANSION_RESV          0xffe0  /* Unused...                   */
-
-/* 1000BASE-T Control register */
-#define ADVERTISE_1000FULL      0x0200  /* Advertise 1000BASE-T full duplex */
-#define ADVERTISE_1000HALF      0x0100  /* Advertise 1000BASE-T half duplex */
-
-/* N-way test register. */
-#define NWAYTEST_RESV1          0x00ff  /* Unused...                   */
-#define NWAYTEST_LOOPBACK       0x0100  /* Enable loopback for N-way   */
-#define NWAYTEST_RESV2          0xfe00  /* Unused...                   */
-
 /* The following are all involved in forcing a particular link
  *  * mode for the device for setting things.  When getting the
  *   * devices settings, these indicate the current mode and whether