diff options
Diffstat (limited to 'contrib/flashimg')
| -rw-r--r-- | contrib/flashimg/Makefile | 29 | ||||
| -rw-r--r-- | contrib/flashimg/flashimg.asm | 497 | ||||
| -rw-r--r-- | contrib/flashimg/flashimg.img | bin | 1856 -> 0 bytes |
3 files changed, 0 insertions, 526 deletions
diff --git a/contrib/flashimg/Makefile b/contrib/flashimg/Makefile deleted file mode 100644 index 39f58e23..00000000 --- a/contrib/flashimg/Makefile +++ /dev/null @@ -1,29 +0,0 @@ -CPPFLAGS = -x assembler-with-cpp -AS86 = as86 -LD86 = ld86 -OBJDUMP = objdump - -.SUFFIXES: .s86 .asm .aout .img - -all: flashimg.img - -clean: - rm -rf *.o *.s86 *.aout *.img - -realclean: clean - rm -rf *.img - -.asm.s86: $*.asm $*.inc - $(CPP) $(CPPFLAGS) -o $@ $*.asm - -.s86.img: $*.s86 - $(AS86) -0 -b $@ $*.s86 - -# .s86.o: $*.s86 -# $(AS86) -0 -a -o $@ $*.s86 -# -# .o.aout: $*.o -# $(LD86) -0 -s -o $@ $*.o -# -# .aout.img: -# dd if=$*.aout of=$@ bs=32 skip=1 diff --git a/contrib/flashimg/flashimg.asm b/contrib/flashimg/flashimg.asm deleted file mode 100644 index 7a37ed54..00000000 --- a/contrib/flashimg/flashimg.asm +++ /dev/null @@ -1,497 +0,0 @@ -; Copyright (C) 1997 Markus Gutschke <gutschk@uni-muenster.de> -; -; This program is free software; you can redistribute it and/or modify -; it under the terms of the GNU General Public License as published by -; the Free Software Foundation; either version 2 of the License, or -; any later version. -; -; This program is distributed in the hope that it will be useful, -; but WITHOUT ANY WARRANTY; without even the implied warranty of -; MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -; GNU General Public License for more details. -; -; You should have received a copy of the GNU General Public License -; along with this program; if not, write to the Free Software -; Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. - -; Prepend this image file to an arbitrary ROM image. The resulting binary -; can be loaded from any BOOT-Prom that supports the "nbi" file format. -; When started, the image will reprogram the flash EPROM on the FlashCard -; ISA card. The flash EPROM has to be an AMD 29F010, and the programming -; algorithm is the same as that suggested by AMD in the appropriate data -; sheets. - - -#define SEGLOW 0xC800 /* lower range for EPROM segment */ -#define SEGHIGH 0xE800 /* upper range for EPROM segment */ -#define AMD_ID 0x2001 /* flash EPROM ID, only support AMD */ -#define ERASE1_CMD 0x80 /* first cmd for erasing full chip */ -#define ERASE2_CMD 0x10 /* second cmd for erasing full chip */ -#define READID_CMD 0x90 /* cmd to read chip ID */ -#define PROG_CMD 0xA0 /* cmd to program a byte */ -#define RESET_CMD 0xF0 /* cmd to reset chip state machine */ - -;---------------------------------------------------------------------------- - - - .text - .org 0 - -; .globl _main -_main: mov ax,#0x0FE0 - mov ds,ax - mov ax,magic ; verify that we have been loaded by - cmp ax,#0xE4E4 ; boot prom - jnz lderr - jmpi 0x200,0x0FE0 ; adjust code segment -lderr: mov si,#loaderr - cld -lderrlp:seg cs - lodsb ; loop over all characters of - or al,al ; string - jnz lderrnx - xor ah,ah - int 0x16 ; wait for keypress - jmpi 0x0000,0xFFFF ; reboot! -lderrnx:mov ah,#0x0E ; print it - mov bl,#0x07 - xor bh,bh - int 0x10 - jmp lderrlp - -loaderr:.ascii "The flash EPROM utility has to be loaded from a BOOT-Prom" - .byte 0xa,0xd - .ascii "that knows about the 'nbi' file format!" - .byte 0xa,0xd - .ascii "Reboot to proceed..." - .byte 0 - - .org 510 - .byte 0x55,0xAA - -!---------------------------------------------------------------------------- - -start: mov ax,cs - mov ds,ax - mov ax,romdata ; verify that there is an Prom image - cmp ax,#0xAA55 ; attached to the utility - jnz resmag - mov al,romdata+2 - or al,al ; non-zero size is required - jnz magicok -resmag: mov si,#badmagic ; print error message -reset: call prnstr - xor ah,ah - int 0x16 ; wait for keypress - jmpi 0x0000,0xFFFF ; reboot! -magicok:mov di,#clrline1 - mov si,#welcome ; print welcome message -inpnew: call prnstr -inprest:xor bx,bx - mov cl,#0xC ; expect 4 nibbles input data -inploop:xor ah,ah - int 0x16 - cmp al,#0x8 ; <Backspace> - jnz inpnobs - or bx,bx ; there has to be at least one input ch - jz inperr - mov si,#delchar ; wipe out char from screen - call prnstr - add cl,#4 ; compute bitmask for removing input - mov ch,cl - mov cl,#0xC - sub cl,ch - mov ax,#0xFFFF - shr ax,cl - not ax - and bx,ax - mov cl,ch -inploop1:jmp inploop -inpnobs:cmp al,#0x0D ; <Return> - jnz inpnocr - or bx,bx ; zero input -> autoprobing - jz inpdone - cmp cl,#-4 ; otherwise there have to be 4 nibbles - jz inpdone -inperr: mov al,#7 ; ring the console bell - jmp inpecho -inpnocr:cmp al,#0x15 ; <CTRL-U> - jnz inpnokl - mov si,di - call prnstr ; clear entire input and restart - jmp inprest -inpnokl:cmp cl,#-4 ; cannot input more than 4 nibbles - jz inperr - cmp al,#0x30 ; '0' - jb inperr - ja inpdig - or bx,bx ; leading '0' is not allowed - jz inperr -inpdig: cmp al,#0x39 ; '9' - ja inpnodg - mov ch,al - sub al,#0x30 -inpnum: xor ah,ah ; compute new input value - shl ax,cl - add ax,bx - test ax,#0x1FF ; test for 8kB boundary - jnz inperr - cmp ax,#SEGHIGH ; input has to be below E800 - jae inperr - cmp ax,#SEGLOW ; and above/equal C800 - jae inpok - cmp cl,#0xC ; if there is just one nibble, yet, - jnz inperr ; then the lower limit ix C000 - cmp ax,#0xC000 - jb inperr -inpok: mov bx,ax ; adjust bitmask - sub cl,#4 - mov al,ch -inpecho:call prnchr ; output new character - jmp inploop1 -inpnodg:and al,#0xDF ; lower case -> upper case - cmp al,#0x41 ; 'A' - jb inperr - cmp al,#0x46 ; 'F' - ja inperr - mov ch,al - sub al,#0x37 - jmp inpnum -inpdone:or bx,bx ; zero -> autoprobing - jnz probe - mov si,#automsg - call prnstr - mov cx,#0x10 - mov bx,#SEGHIGH ; scan from E800 to C800 -autoprb:sub bx,#0x0200 ; stepping down in 8kB increments - mov di,bx - call readid - cmp ax,#AMD_ID - jz prbfnd - loop autoprb - mov si,#failmsg -nofnd: mov di,#clrline2 - jmp near inpnew ; failure -> ask user for new input -probe: mov di,bx - test bx,#0x07FF ; EPROM might have to be aligned to - jz noalign ; 32kB boundary - call readid - cmp ax,#AMD_ID ; check for AMDs id - jz prbfnd - mov si,#alignmsg - call prnstr - and bx,#0xF800 ; enforce alignment of hardware addr -noalign:call readid ; check for AMDs id - cmp ax,#AMD_ID - jz prbfnd - mov si,#nofndmsg ; could not find any EPROM at speci- - call prnstr ; fied location --- even tried - mov si,#basemsg ; aligning to 32kB boundary - jmp nofnd ; failure -> ask user for new input -prbfnd: mov si,#fndmsg - call prnstr ; we found a flash EPROM - mov ax,bx - call prnwrd - mov si,#ersmsg - call prnstr - call erase ; erase old contents - jnc ersdone - mov si,#failresmsg ; failure -> reboot machine - jmp near reset -ersdone:mov si,#prg1msg ; tell user that we are about - call prnstr ; to program the new data into - mov ax,di ; the specified range - call prnwrd - mov si,#prg2msg - call prnstr - xor dh,dh - mov dl,romdata+2 - shl dx,#1 - mov ah,dh - mov cl,#4 - shl ah,cl - xor al,al - add ax,di - call prnwrd - mov al,#0x3A ; ':' - call prnchr - mov ah,dl - xor al,al - dec ax - call prnwrd - mov al,#0x20 - call prnchr - mov dh,romdata+2 ; number of 512 byte blocks - push ds - mov ax,ds - add ax,#romdata>>4 ; adjust segment descriptor, so that - mov ds,ax ; we can handle images which are -prgloop:mov cx,#0x200 ; larger than 64kB - xor si,si - xor bp,bp - call program ; program 512 data bytes - jc prgerr ; check error condition - mov ax,ds - add ax,#0x20 ; increment segment descriptors - mov ds,ax - add di,#0x20 - dec dh ; decrement counter - jnz prgloop - pop ds - mov si,#donemsg ; success -> reboot -prgdone:call prnstr - mov si,#resetmsg - jmp near reset -prgerr: pop ds ; failure -> reboot - mov si,#failresmsg - jmp prgdone - - -;---------------------------------------------------------------------------- - -; READID -- read EPROM id number, base address is passed in BX -; ====== -; -; changes: AX, DL, ES - -readid: mov dl,#RESET_CMD ; reset chip - call sendop - mov dl,#READID_CMD - call sendop ; send READID command - mov es,bx - seg es - mov ax,0x00 ; read manufacturer ID - mov dl,#RESET_CMD - jmp sendop ; reset chip - - -;---------------------------------------------------------------------------- - -; ERASE -- erase entire EPROM, base address is passed in BX -; ===== -; -; changes: AL, CX, DL, ES, CF - -erase: mov dl,#ERASE1_CMD - call sendop ; send ERASE1 command - mov dl,#ERASE2_CMD - call sendop ; send ERASE2 command - xor bp,bp - mov al,#0xFF - push di - mov di,bx - call waitop ; wait until operation finished - pop di - jnc erfail - mov dl,#RESET_CMD - call sendop ; reset chip - stc -erfail: ret - - -;---------------------------------------------------------------------------- - -; PROGRAM -- write data block at DS:SI of length CX into EPROM at DI:BP -; ======= -; -; changes: AX, CX, DL, BP, ES, CF - -program:mov dl,#PROG_CMD - call sendop ; send programming command - lodsb ; get next byte from buffer - mov es,di - seg es - mov byte ptr [bp],al ; write next byte into flash EPROM - call waitop ; wait until programming operation is - jc progdn ; completed - inc bp - loop program ; continue with next byte - clc ; return without error -progdn: ret - - -;---------------------------------------------------------------------------- - -; SENDOP -- send command in DL to EPROM, base address is passed in BX -; ====== -; -; changes: ES - -sendop: mov es,bx - seg es - mov byte ptr 0x5555,#0xAA ; write magic data bytes into - jcxz so1 ; magic locations. This unlocks -so1: jcxz so2 ; the flash EPROM. N.B. that the -so2: seg es ; magic locations are mirrored - mov byte ptr 0x2AAA,#0x55 ; every 32kB; the hardware address - jcxz so3 ; might have to be adjusted to a -so3: jcxz so4 ; 32kB boundary -so4: seg es - mov byte ptr 0x5555,dl - ret - - -;---------------------------------------------------------------------------- - -; WAITOP -- wait for command to complete, address is passed in DI:BP -; ====== -; -; for details on the programming algorithm, c.f. http://www.amd.com -; -; changes: AX, DL, ES, CF - -waitop: and al,#0x80 ; monitor bit 7 - mov es,di -wait1: seg es ; read contents of EPROM cell that is - mov ah,byte ptr [bp] ; being programmed - mov dl,ah - and ah,#0x80 - cmp al,ah ; bit 7 indicates sucess - je waitok - test dl,#0x20 ; bit 5 indicates timeout/error - jz wait1 ; otherwise wait for cmd to complete - seg es - mov ah,byte ptr [bp] ; check error condition once again, - and ah,#0x80 ; because bits 7 and 5 can change - cmp al,ah ; simultaneously - je waitok - stc - ret -waitok: clc - ret - -;---------------------------------------------------------------------------- - -; PRNSTR -- prints a string in DS:SI onto the console -; ====== -; -; changes: AL - -prnstr: push si - cld -prns1: lodsb ; loop over all characters of - or al,al ; string - jz prns2 - call prnchr ; print character - jmp prns1 -prns2: pop si - ret - - -;---------------------------------------------------------------------------- - -; PRNWRD, PRNBYT, PRNNIB, PRNCHR -- prints hexadezimal values, or ASCII chars -; ====== ====== ====== ====== -; -; changes: AX - -prnwrd: push ax - mov al,ah - call prnbyt ; print the upper byte - pop ax -prnbyt: push ax - shr al,1 ; prepare upper nibble - shr al,1 - shr al,1 - shr al,1 - call prnnib ; print it - pop ax -prnnib: and al,#0x0F ; prepare lower nibble - add al,#0x30 - cmp al,#0x39 ; convert it into hex - jle prnchr - add al,#7 -prnchr: push bx - mov ah,#0x0E ; print it - mov bl,#0x07 - xor bh,bh - int 0x10 - pop bx - ret - - -;---------------------------------------------------------------------------- - -magic: .byte 0xE4,0xE4 - -badmagic:.byte 0xa,0xd - .ascii "There does not appear to be a ROM image attached to the" - .ascii "flash EPROM utility;" - .byte 0xa,0xd -resetmsg:.ascii "Reboot to proceed..." - .byte 0 - -welcome:.byte 0xa,0xd - .ascii "Flash EPROM programming utility V1.0" - .byte 0xa,0xd - .ascii "Copyright (c) 1997 by M. Gutschke <gutschk@uni-muenster.de>" - .byte 0xa,0xd - .ascii "===========================================================" - .byte 0xa,0xd -prompt: .byte 0xa,0xd - .ascii "Enter base address for AMD29F010 flash EPROM on FlashCard or" - .byte 0xa,0xd - .ascii "press <RETURN> to start autoprobing; the base address has" - .byte 0xa -clrline1:.byte 0xd - .ascii "to be in the range C800..E600: " - .ascii " " - .byte 0x8,0x8,0x8,0x8 - .byte 0 - -delchar:.byte 0x8,0x20,0x8 - .byte 0 - -automsg:.ascii "autoprobing... " - .byte 0 - -failmsg:.ascii "failed!" -basemsg:.byte 0xa -clrline2:.byte 0xd - .ascii "Enter base address: " - .ascii " " - .byte 0x8,0x8,0x8,0x8 - .byte 0 - -fndmsg: .byte 0xa,0xd - .ascii "Found flash EPROM at: " - .byte 0 - -alignmsg:.byte 0xa,0xd - .ascii "FlashCard requires the hardware address to be aligned to a" - .byte 0xa,0xd - .ascii "32kB boundary; automatically adjusting..." - .byte 0 - -nofndmsg:.byte 0xa,0xd - .ascii "No AMD29F010 flash EPROM found" - .byte 0 - -ersmsg: .byte 0xa,0xd - .ascii "Erasing old contents... " - .byte 0 - -prg1msg:.ascii "done" - .byte 0xa,0xd - .ascii "Programming from " - .byte 0 - -prg2msg:.ascii ":0000 to " - .byte 0 - -donemsg:.ascii "done!" - .byte 0xa,0xd - .byte 0 - -failresmsg: - .ascii "failed!" - .byte 0xa,0xd - .byte 0 - - -;---------------------------------------------------------------------------- - - .align 16 - .org *-1 - .byte 0x00 -romdata: diff --git a/contrib/flashimg/flashimg.img b/contrib/flashimg/flashimg.img Binary files differdeleted file mode 100644 index 263d3392..00000000 --- a/contrib/flashimg/flashimg.img +++ /dev/null |